Abstract
This article reports the results of a study to determine the effects of austenite stability, with respect to the strain-induced transformation to martensite, on the formability of 300 series stainless steels. The effects were evaluated as a function of alloy content, deformation temperature, and deformation rate. Three stainless-steel alloys with different nickel contents were evaluated as commercially cold-rolled and annealed sheet products. Tensile tests were performed at temperatures between −60°C and +125°C and at strain rates from 0.00167 s−1 to 0.167 s−1. The combined effects of strain, strain state, deformation-induced temperature changes, and strain rate are considered to explain the interrelationships between martensite formation and limit strains as observed in forming-limit diagrams.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
T. Angel, “Formation of Martensite in Austenitic Stainless Steels. Effects of Deformation, Temperature, and Composition,”J. of the ISI, 5 (1954), pp. 165–174.
S.S. Hecker et al., “Effects of Strain State and Strain Rate on Deformation-Induced Transformation in 304 Stainless Steel: Part I. Magnetic Measurements and Mechanical Behavior,”Met. Trans. A, 13A (1982), pp. 619–626.
G.L. Huang, D.K. Matlock, and G. Krauss, “Martensite Formation, Strain Rate Sensitivity, and Deformation Behavior of Type 304 Stainless Steel Sheet,”Met. Trans. A, 20A (1989), pp. 1239–1246.
D.C. Ludwigson and J.A. Berger, “Plastic Behaviour of Metastable Austenitic Stainless Steels,”J. of the ISI, 1 (1969), pp. 63–69.
G.B. Olson and M. Cohen, “Kinetics of Strain-Induced Martensitic Nucleation,”Met. Trans. A, 6A (1975), pp. 791–795.
A. Kumar and L.K. Singhal, “Effect of Temperature and Strain Distribution on Martensitic Transformation during Uniaxial Testing of AISI-304 Stainless Steel,”Met. Trans. A, 19A (1988), pp. 1021–1026.
A. Kumar and L.K. Singhal, “Effect of Strain Rate on Martensitic Transformation during Uniaxial Testing of AISI-304 Stainless Steel,”Met. Trans. A, 20A (1989), pp. 2857–2859.
J.A.C. Ramirez et al., “Flow Stress and Phase Transformation Analyses in the Austenitic Stainless Steel under Cold Working. Part 1, Phase Transformation Characteristics and Constitutive Formulation by Energetic Criterion,”JSME International Journal, 35 (1), (1992), pp. 201–209.
T. Tsuta and J.A. Cortes R., “Flow Stress and Phase Transformation Analyses in Austenitic Stainless Steel under Cold Working. Part 2, Incremental Theory Under Multiaxial Stress State by the Finite-Element Method,”JSME International Journal, 36 (1) (1993), pp. 63–72.
K. Shinagawa, K. Mori, and K. Osakada, “Finite Element Simulation of Deep Drawing of Stainless Steel Sheet with Deformation-Induced Transformation,”J. of Mat. Proc. Tech., 27 (1991), pp. 301–310.
R.G. Stringfellow, D.M. Parks, and G.B. Olson, “A Constitutive Model for Transformation Plasticity Accompanying Strain-Induced Martensitic Transformations in Metastable Austenitic Steels,”Acta Metallurgica et Materialia, 40 (7) (1992), pp. 1703–1716.
G.J. Coubrough, D.K. Matlock, and C.J. Van Tyne,Formability of Type 304 Stainless Steel Sheet, SAE technical paper 930814 (1993), pp. 279–289.
A. Graf and W.F. Hosford, “Calculations of Forming Limit Diagrams,”Met. Trans. A, 21A (1990), pp. 87–94.
K.J. Blom, “Press Formability of Stainless Steels,”Stainless Steel '77 (London: Amax, 1977), pp. 213–216.
A.S. Korhonen, “Work-Hardening and Formability of Austenitic Stainless Steel Sheets,”Sheet Metal Industries, 5 (1978), pp. 598–606.
I.A. Franson, Allegheny Ludlum Technical Center, private communication, May 1995.
A.H. Eichelman and F.C. Hull, “The Effect of Composition on the Temperature of Spontaneous Transformation of Austenite to Martensite in 18-8 Type Stainless Steel,”Transactions of the ASM, 45 (1953), pp. 77–104.
Lectroetch Company,Electrochemical Marking Manual (East Cleveland, OH: Lectroetch Co., 1971), pp. 18–19.
D.A. Burford, “Frictional and Geometric Effects in Punch-Stretch Sheet Metal Formability Testing,” Ph.D. thesis, Colorado School of Mines (1987).
E.P. Cooke, R.P. Foley, and D.K. Matlock,Formability of Ferritic Stainless Steel Sheet, ASPPRC research report MT-SRC-095-020 (Colorado School of Mines: ASPPRC September 1, 1995).
S.F. Peterson, “Formability of Austenitic Stainless Steels,” M.S. thesis, Colorado School of Mines (1996).
G.E. Dieter,Mechanical Metallurgy (New York, NY: McGraw-Hill, 1986), pp. 88–89.
G.B. Olson and M. Cohen, “Stress-Assisted Isothermal Martensitic Transformation: Application to TRIP Steels,”Met. Trans. A, 13A (1982), pp. 1907–1914.
Additional information
S.F. Peterson earned his M.S. in metallurgical and materials engineering from the Colorado School of Mines in 1997. He is currently an engineer at Case Corporation.
M.C. Mataya earned his Ph.D. in metallurgy and materials science from Marquette University in 1976. He is currently an engineer at the Rocky Flats Technology Site.
D.K. Matlock earned his Ph.D. in materials science and engineering from Stanford University in 1972. He is currently a professor at the Colorado School of Mines. Dr. Matlock is also a member of TMS.
Rights and permissions
About this article
Cite this article
Peterson, S.F., Mataya, M.C. & Matlock, D.K. The formability of austenitic stainless steels. JOM 49, 54–58 (1997). https://doi.org/10.1007/BF02914352
Issue Date:
DOI: https://doi.org/10.1007/BF02914352