Abstract
The aim of this article is to present the beneficial effect of a reduction of silicon content on coarse-grained heat-affected zone (CGHAZ) toughness. This study was achieved with experi-mental and industrial E355 structural steels. These 0.09 wt pct C steels were Ti-microalloyed with silicon contents ranging from 0.05 to 0.5 wt pct. First, we demonstrate that the CGHAZ toughness is predominantly affected by the volume fraction of retained austenite (γr). Second, we show that the existence of retained austenite pertains only to its carbon enrichment. This enrichment is promoted essentially by an increase of the silicon level due to the retarding action of silicon on the formation of carbides in ferrite as well as in austenite. In the same way, the increase of silicon content slows down the decomposition of retained austenite into pearlite. The reduction of the silicon content of the steel greatly increases the ductility of the CGHAZ through the decrease of the volume fraction of retained austenite.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
K.E. Easterling:Introduction to the Physical Metallurgy of Welding, Butterworth and Co., London, 1983, pp. 104–218.
M. Toyoda: Osaka University Report, Part I and II, Osaka, Japan 1988.
D. Rosenthal:Trans. ASME, 1946, vol. 68, pp. 849–62.
P. Verrier, T. Maurickx, R. Taillard, and G. Guarrigues:8th Int. Conf. on Offshore Mechanics and Arctic Engineering, ASME, New York, NY, 1989, pp. 641–47.
R. Taillard, J. Foct, P. Verrier, and T. Maurickx:The Martensitic Transformation in Science and Technology, E. Hornbogen and N. Jost, eds., Bochum, Germany, 1989, pp. 495–502.
P. Verrier: Doctoral Thesis, University of Lille I, France, 1990.
R. Taillard, P. Verrier, T. Maurickx, and J. Foct:Welding ’90, M. KoÇak ed., I.I.T.T., Paris, 1990, pp. 229–36.
J.H. Chen, Y. Kikata, T. Araki, M. Yoneta, and Y. Matsuda:Acta Metall., 1984, vol. 32, pp. 1779–88.
T. Maurickx: Doctor Eng. Thesis, University of Lille I, France, 1987.
T. Maurickx and R. Taillard:High Nitrogen Steels ’88, J. Foct and A. Hendry, eds., The Institute of Metals, London, 1988, pp. 327–32.
N.E. Hannerz: Report No. 70-728/U 615, Swedish Board of Technical Development, Stockolm, 1972.
T. Maurickx, R. Taillard, and J. Foct:C.R. Acad. Sci., 1986, vol. 303, series II, pp. 41–46.
O.M. Akselsen, O. Grøng, and J.K. Solberg:Mater. Sci. Technol., 1987, vol. 8, pp. 649–55.
Y. Kasamatsu, S. Takashima, and T. Hosoya:J. Iron Steel Inst. Jpn., 1979, vol. 25, pp. 92–101.
J.H. Ladriere and X.J. He:Mater. Sci. Eng., 1986, vol. 77, pp. 133–38.
T.E. Cranshaw, B.W. Dale, G.O. Longworth, and C.E. Johnson:Mössbauer Spectrometry and its Applications, Cambridge University Press, Cambridge, U.K., 1985, pp. 69–76.
K.W. Andrews:J. Iron Steel Inst. London, 1965, vol. 203, pp. 721–27.
R. Taillard, T. Maurickx, and J. Foct:Electron Microscopy and Analysis, Institute Physics Conference Series, Adam Hilger Ltd., London, 1985, pp. 391–94.
M. Sarikaya, G. Thomas, and J.W. Steeds:Solid-solid Phase Transformations, H.I. Aaronson, D.E. Laughlin, R.F. Sekerka, and CM. Wayman, eds., TMS-AIME, Warrendale, PA, 1981, pp. 1421–25.
A.D. Romig and R. Salzbrenner:Solid-solid Phase Transformations, H.I. Aaronson, D.E. Laughlin, R.F. Sekerka, and CM. Wayman, eds., TMS-AIME, Warrendale, P.A.. 1981, pp. 849–53.
L.J. Cuddy and J.C Raley:Metall. Trans. A, 1983, vol. 14A, pp. 1989–95.
A. De Sy and J. Vidts:Métallurgie Structurale, Dunod, Paris, 1968, 2nd ed., pp. 352–353.
I. Tamura, C. Ouchi. T. Tanaka, and H. Sekine:Thermomechanical Processing of High Strength Low Alloy Steels, Butterworth and Co., London, 1988, pp. 17–18.
J. Pomey:Rev. Métall., M.T., 1966, vol. LXIII, pp. 509–532.
A. De Sy and J. Vidts:Métallurgie Structurale, Dunod, Paris, 1968, 2nd ed., pp. 297–303.
J.S. Kirkaldy, B.A. Thomson, and E.A. Baganis:Hardenability Concepts with Applications to Steel, D.V. Doane and J.S. Kirkaldy, eds., TMS-AIME, Warrendale, PA, 1978, pp. 82–125.
H.C Chen, H. Era, and M. Shimizu:Metall. Trans. A, 1989, vol. 20A, pp. 437–55.
S.K. Liu, W.T. Reynolds, H. Hu, G.J. Shiflet, and H.I. Aaronson:Metall. Trans. A, 1985, vol. 16A, pp. 457–67.
S.J. Barnard, G.D.W. Smith, A.J. Garratt-Reed, and J. Vander Sande:Solid-solid Phase Transformations, H.I. Aaronson, D.E. Laughlin, R.F. Sekerka, and CM. Wayman, eds., TMS-AIME, Warrendale, P.A., 1981, pp. 881–85.
H.K.D.H. Badeshia and D.V. Edmonds:Metall. Trans. A, 1979, vol. 10A, pp. 895–907.
P.R. Williams, M.K. Miller, and G.D.W. Smith:Solid-solid Phase Transformations, H.I. Aaronson, D.E. Laughlin, R.F. Sekerka, and CM. Wayman, eds., TMS-AIME, Warrendale, P.A., 1981, pp. 813–17.
G. Bernard:Cahiers d’ Informations Techniques, Institut de Recherches de la Sidérurgie FranÇaise, Saint Germain en Laye, France, 1979, vol. 2, pp. 249–65.
O.M. Akselsen, Ø. Grong, and P.E. Kvaale:Metall. Trans. A, 1986, vol. 17A, pp. 1529–36.
N.J. Petch:Acta Metall., 1986, vol. 34, pp. 1387–93.
Y. Tomita and O. Okabayashi:Metall. Trans. A, 1986, vol. 17A, pp. 1203–09.
Author information
Authors and Affiliations
Additional information
Formerly Graduate Students, Physical Metallurgy Laboratory, University of Lille.
Rights and permissions
About this article
Cite this article
Taillard, R., Verrier, P., Maurickx, T. et al. Effect of silicon on CGHAZ toughness and microstructure of microalloyed steels. Metall Mater Trans A 26, 447–457 (1995). https://doi.org/10.1007/BF02664681
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF02664681