Abstract
Using laser anemometry, laser fluxmetry, and statistical two-color pyrometry, the velocity, number flux, and surface temperature distributions of alumina and zirconia particles in dc plasma jets have been determined inflight for various spraying parameters. The flux measurements emphasized the importance of the carrier gas flow rate, which must be adjusted to the plasma jet momentum depending on the arc current, nozzle diameter, gas flow rate, and gas nature. It has also been shown that the particle trajectories depend both on the particle size and injection velocity distributions and that the position and tilting of the injector plays a great role. The particle size drastically influences its surface temperature and velocity, and for the refractory materials studied, only the particles below 45 μm in diameter are fully molten in Ar-H2 (30 vol%) plasma jets at 40 kW. The morphology of the particles is also a critical parameter. The agglomerated particles partially explode upon penetration into the jet, and the heat propagation phenomenon is seriously enhanced, particularly for particles larger than 40 μm. The effects of the arc current and gas flow rate have been studied, and the results obtained in an air atmosphere cannot be understood without considering the enhanced pumping of air when the plasma velocity is increased. The Ar-He (60 vol%) and Ar-H2 (30 vol%) plasma jets, when conditions are found where both plasma jets have about the same dimensions, do not result in the same treatment for the particles. The particles are not as well heated in the Ar-He jet compared to the Ar-H2 jet. Where the surrounding atmosphere is pure argon instead of air (in a controlled atmosphere chamber), he radial velocity and temperature distributions are broadened, and if the velocities are about the same, the temperatures are higher. The use of nozzle shields delays the air pumping and increases both the velocity and surface temperature of the particles. However, the velocity increase in this case does not seem to be an advantage for coating properties.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
N.N. Rykalin and V.V. Kudinov, Plasma Spraying,Pure Appl. Chem., Vol 48, 1976, p 229–239
J.H. Zaat, Thermal Spraying,Ann. Rev. Mater. Sci., Vol 13, 1983, p 9–42
Thermal Spraying, Practice, Theory and Applications, American Welding Society, 1985
Technology Forecast,Adv. Mater. Proc, Vol 30, 1988
P. Fauchais, A. Grimaud, A. Vardelle, and M. Vardelle, Plasma Spraying: A Review,Ann.Phys. Fr., Vol 14, 1989, p 261–310
P. Fauchais, J.F. Coudert, A. Vardelle, M. Vardelle, and A. Denoirjean, Diagnostics of Thermal Spraying Plasma Jets,J. Thermal Spray Technol., Vol 1 (No. 2), 1992, p 117–128
P. Fauchais, J.F. Coudert, and M. Vardelle, Diagnostics in Thermal Plasma Processing, inPlasma Diagnostics, Academic Press, 1989, p 349–446
L. Gyenis, A. Grimaud, O. Betoule, F. Monerie-Moulin, P. Fauchais, and M. Ducos, “Influence of Temperature Control during Spraying on Hardness and Cohesion of Alumina Coatings,” Proc. 2nd Plasma Technik Symposium, Vol 1, S. Blum-Sandmeier, H. Eschnauer, P. Huber, and A.R. Nicoll, Ed., Wohlen, Switzerland, 1991, p 95–101
M. Vardelle, “Study of Heat, Mass and Momentum Transfers Between A dc Plasma Jet and Powders,” State thesis, University of Limoges, France, July, 1987
M. Vardelle, A. Vardelle, and P. Fauchais,“Experimental Study of the Thermal Exposure Experienced by Powders under Plasma Spraying Conditions in Air and Inert Environment,” Proc. 1st Plasma Technik Symposium, Vol 2, P. Huber and H. Eschnauer, Ed., Wohlen, Switzerland, 1988, p 167–178
E. Pfender, Particle Behavior in Thermal Plasmas,Plasma Chem. Plasma Proc, Vol 9, 1989, p 167S-194S
E. Bourdin, P. Fauchais, and M.I. Boulos, Transient Heat Conduction under Plasma Conditions,Int. J. Heat Mass Transfer, Vol 26, 1983, p 567–582
G. Schweir, Plasma Spray Powders for TBCs,Advances in Thermal Spraying, Pergamon Press, 1986, p 277–286
B.A. Kusher, S. Rangaswany, and A.J. Rotolico,“Thermal Spray Powders: Manufacturing Methods and Quality Control Procedures,” Proc. 1st Plasma Technik Symposium, Vol 2, P. Huber and H. Eschnauer, Ed., Wohlen, Switzerland, 1988, p 191–202
M. Vardelle, A. Vardelle, A. Denoirjean, and P. Fauchais, Heat Treatment of Zirconia Powders with Different Morphologies under Thermal Plasma Conditions,Mater. Res. Soc. Symp. Proc, MRS, 190, 1991, p 175–183
D. Bernard,“Plasma Spraying of TBCs,” Ph.D. thesis, University of Limoges, France, June 1990
E. Lugsheider, I. Rass, H.L. Heijnen, P. Chandler, T. Cosak, P. Fauchais, A. Denoirjean, and A. Vardelle, Comparison of the Coatings Properties of Different Types of Powder Morphologies,Thermal Spray: International Advances in Coatings Technology, C.C. Berndt, Ed., ASM International, 1992, p 967–973
R. Spores, E. Pfender, Flow Structure of A Turbulent Thermal Plasma Jet,Surf. Coat. Technol, Vol 37, 1989, p 251–260
Ph. Roumilhac, J.F. Coudert, and P. Fauchais, Influence of the Arc Chamber Design on the Characteristics and Temperature Distributions of Ar-H2 and Ar-He Spraying Plasma Jets,Mater. Res. Soc. Symp. Proc, MRS, 190, 1991, p227–238
B. Pateyron, F. Elchinger, G. Delluc, and P. Fauchais, Thermodynamic and Transport Properties of Ar-H2 and Ar-He Plasma Gases Used for Spraying at Atmospheric Pressure,Plasma Chem. Plasma Proc, Vol 12 (No. 4), 1992, p 421–448
Ph. Roumilhac, M. Vardelle, A. Vardelle, and P. Fauchais, Comparison of Heat and Momentum Transfer to Ceramic Particles Sprayed in Ar-He and Ar-H2 at Atmospheric Pressure,Thermal Spray Technology: New Ideas and Processes, D.L. Houck, Ed., ASM International, 1989, p 111–116
M. Vardelle, A. Vardelle, Ph. Roumilhac, and P. Fauchais, Influence of the Surrounding Atmosphere under Plasma Spraying Conditions,Thermal Spray Technology: New Ideas and Processes, D.L. Houck, Ed., ASM International, 1989, p 117–121
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Vardelle, M., Vardelle, A. & Fauchais, P. Spray parameters and particle behavior relationships during plasma spraying. JTST 2, 79–91 (1993). https://doi.org/10.1007/BF02647426
Issue Date:
DOI: https://doi.org/10.1007/BF02647426