Abstract
It has been reported for as-quenched AISI 4340 steel that high temperature austenitizing treatments at 1200°C, instead of conventional heat-treatment at 870°C, result in a two-foldincrease in fracture toughness,K Ic, but adecrease in Charpy impact energy. This paper seeks to find an explanation for this discrepancy in Charpy and fracture toughness data in terms of the difference betweenK Ic and impact tests. It is shown that the observed behavior is independent of shear lip energy and strain rate effects, but can be rationalized in terms of the differing response of the structure produced by each austenitizing treatment to the influence of notch root radius on toughness. The microstructural factors which affect this behavior are discussed. Based on these and other observations, it is considered that the use of high temperature austenitizing be questioned as a practical heat-treatment procedure for ultrahigh strength, low alloy steels. Finally, it is suggested that evaluation of material toughness should not be based solely onK Ic or Charpy impact energy values alone; both sharp crack fracture toughness and rounded notch impact energy tests are required.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
G. Y. Lai, W. E. Wood, R. A. Clark, V. F. Zackay, and E. R. Parker:Met. Trans., 1974, vol. 5, p. 1663.
D. Dulieu: Discussion to paper by V. F. Zackay, E. R. Parker, and W. E. Wood;Proc. Third Intl. Conf. on the Strength of Metals and Alloys, vol. 2, p. 383, Institute of Metals/Iron and Steel Institute, Cambridge, England, Aug. 1973.
W. E. Wood, E. R. Parker, and V. F. Zackay: Rept. No. LBL-1474, Lawrence Berkeley Laboratory, University of California, Berkeley, Calif. 94720, May, 1973.
A. A. Anctil and E. B. Kula: unpublished research, Army Materials and Me- chanics Research Center, Watertown, Mass., 1975.
Annual Book of ASTM Standards (American Society for Testing and Materials), ASTM Standards E399-74, Philadelphia, 1974.
Annual Book of ASTM Standards, (American Society for Testing and Mater- ials), p. 276, ASTM Standards E23-72, Philadelphia, 1972.
W. L. Server and A. S. Tetelman:Eng. Fract. Mech., 1972, vol. 4, p. 367.
W. L. Server, D. R. Ireland, and R. A. Wullaert: Dynatup Technical Rept. No. TR 74-29R, Effects Technology, Inc., Santa Barbara, California 93105, November 1974.
T. R. Wilshaw, A. Rau, and A. S. Tetelman:Eng. Fract. Mech., 1968, vol. 1, p. 191.
J. Malkin and A. S. Tetelman:ibid, 1971, vol. 3, p. 151.
P. T. Heald, G. M. Spink, and P. J. Worthington:Mater. Sci. Eng., 1972, vol. 10, p. 129.
S. Ensha and A. S. Tetelman: UCLA Tech. Rept., No. 14, UCLA-ENG-7435, SchoolofEngineeringandAppliedScience, University of California, Los Angeles, Calif. 90024, May 1974.
A. H. Cottrell:The Mechanical Properties of Matter, p. 365, John Wiley & Sons, New York, 1964.
A. S. Tetelman, T. R. Wilshaw, and A. Rau:Int. J. Fract. Mech., 1968, vol. 4, p. 147.
R. O. Ritchie, J. F. Knott, and J. R. Rice:J. Mech. Phys. Solids, 1973, vol. 21, p. 395.
J. R. Rice and M. A. Johnson:Inelastic Behavior of Solids, M. F. Kanninenefal, eds., p. 641, McGraw Hill, New York, 1970.
J. R. Griffiths and D. R. J. Owen:J. Mech. Phys. Solids, 1971, vol. 19, p. 149.
G. Chipperfield and J. F. Knott:Metals Technol., 1975, vol. 2, p. 45.
B. J. Schulz and J. McMahon, Jr.: ASTM STP No. 499. p. 104, American Society for Testing and Materials, 1972.
G. Clark, R. O. Ritchie, and J. F. Knott:Nature Phys. Sci., 1972. vol. 239, p. 104.
B. J. Schulz and J. McMahon, Jr.:Met. Trans., 1973, vol. 4, p. 2485.
R.O. Ritchie and J. F. Knott:ibid, 1974, vol. 5. p. 782.
G. Thomas:Iron Steel International, 1973, vol. 46. p. 451.
G. Y. Lai:Mater. Sci. Eng., 1975. vol. 19, p. 153.
W. E. Wood:Eng. Fract. Mech., 1975. vol. 7. p. 219.
S. K. Das and G. Thomas:Trans. ASM, 1969. vol. 62. p. 659.
J. A. McMahon and G. Thomas:Proc. Third Intl. Conf. on the Strength of Metals and Alloys, vol. 1, p. 180. Institute of Metals/Iron and Steel Institute, Cambridge, England, Aug. 1973.
R. O. Ritchie, L. E. Geniets, and J. F. Knott:ibid, p. 124.
R. A. Clark and G. Thomas:Met. Trans. A, 1975, vol. 6A,p.969.
J. R. Rellick and J. McMahon, Jr.:Met. Trans., 1974, vol. 5, p. 2439.
V. F. Zackay, E. R. Parker, R. D. Goolsby, and W. E. Wood:Nature Phys. Sci., 1972, vol. 236, p. 108.
T. Tom: D. Eng. Thesis, Rept. No. LBL-1856, Lawrence Berkeley Laboratory, University of California, Berkeley, Calif. 94720. Sept. 1973.
Author information
Authors and Affiliations
Additional information
formerly with Effects Technology, Inc., Santa Barbara, CA
Rights and permissions
About this article
Cite this article
Ritchie, R.O., Francis, B. & Server, W.L. Evaluation of toughness in AISI 4340 alloy steel austenitized at low and high temperatures. Metall Trans A 7, 831–838 (1976). https://doi.org/10.1007/BF02644080
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF02644080