Abstract
In this study a relationship between the surface and textural properties of carbon blacks and the gasification process induced thermally in air is noted. A temperature jump method was used to follow the gasification in air and to establish the relevant Arrhenius parameters. This can be associated with the activity of ‘basal’ plane carbon atoms as well as ‘edge’ carbon atoms at the surface. This is based on a model of carbon black structure consisting of the irregular packing of small graphite carbon structures. The carbon black surface was measured using a single measurement of adsorption based essentially on the BET volumetric method. The carbon black surface had a rate of oxidation per unit are which clearly indicated that the lower area carbon blacks had a predominately active area of ‘edge’ atoms at the surface while the surface of the higher area carbon blacks had a predominate amount of ‘basal’ plane graphite carbon atoms.
Zusammenfassung
Es wird eine Beziehung zwischen den Oberflächen- und Texturmerkmalen von Ruß und den in Luft thermisch induzierten Vergasungsvorgängen hergestellt. Unter Anwendung der Temperatursprung-Methode wurde die Vergasung in Luft verfolgt, um die relevanten Arrhenius'schen Parameter zu ermitteln. Dies kann mit der Aktivität der “basalen” Ebenematome sowie der “Kanten” atome in Verbindung gebracht werden. Dies basiert auf einem Modell der Ru\struktur, bestehend aus einer unregelmäßigen Packung von kleinen Graphit- Strukturen. Die Rußoberfläche wurde mit einer Adsoptions-Einzelmessung vermessen, die im wesentlichen auf der volummetrischen BET Methode basiert. Die Rußoberfläche besaß eine Oxidationsgeschwindigkeit pro Flächeneinheit, die eindeutig zeigt, daß Ruß mit geringerer Fläche an der Oberfläche ein vorwiegend aktives Gebiet von “Kanten” atomen besitzt, während die Oberfläche von Ruß mit größerer Fläche eine vorwiegende Menge von “basalen” Graphitebenen-Atome besitzt.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
H. W. Davidson, P. K. C. Wiggs, A. H. Churchover, F. A. P. Maggs and R. S. Bradley, Manufactured Carbon, Pergamon Press, Oxford 1968, p. 111.
F. A. Heckman, Rubber Chem. Technol., 37 (1964) 245.
S. Ergun, Carbon, 6 (1968) 141.
ASTM Designation D 3037-86
ASTM Designation D 3037-86
S. Brunauer, P. H. Emmett and E. Teller, J. Amer. Chem. Soc., 60 (1938) 309.
ASTM Designation 1765-87a
ASTM Designation D 1510-85
D. W. Brazier, Rubber Chemistry and Technology, 153 (1980) 438.
D. Dollimore, P. Spooner and A. Turner, Surface Technology, 4 (1976) 121.
J. M. Haynes, Clay Min. Bull., 4 (1959) 69.
A. L. Klyachko-Gurvich, Izvest. Acad. Navk, SSSR, Otdel, Khim. Nauk., (1961) 1884, (Eng. Transl.) (1961) 1756.
D. Dollimore and A. Turner, Trans. Farad. Soc., 66 (1970) 2655.
R. O. Grisdale, J. Appl. Physics, 24 (1953) 1288.
W. R. Smith and M. H. Polley, J. Phys. Chem., 60 (1956) 689.
D. Dollimore, P. Manley, W. A. Kneller and Wang Jin Yong, Proc. 17th North Amer. Thermal Analyis Soc. Conf., Lake Buena Vista, Florida 1988 p. 644.
A. F. Armington, Ph. D. Thesis, Penn. State Univ., 1960.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Azizi, J.A., Dollimore, D., Dollimore, P.J. et al. Application of thermal analysis to carbon black-elastomer systems. Journal of Thermal Analysis 40, 831–847 (1993). https://doi.org/10.1007/BF02546657
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF02546657