Abstract
The effect of interphase modulus and cohesive energy on critical fibre length in short-fibre reinforced brittle composites has been investigated employing computer simulation. The simulation consists of a two-dimensional computer model based upon a discrete network of grid points. Failure is defined in terms of an energy criterion, where the energy is calculated on the basis of a two- and three-body interaction between the grid points. Simulation results show that for a whisker-type fibre, a thick interphase (i.e. A i>Af where A represents the cross sectional area) with an elastic modulus less than that of the matrix in combination with an increased interphase toughness greatly reduce the critical aspect ratio, for both metal-matrix and ceramic-reinforced brittle polymer composites. The results also show a variation in the failure mode from tensile failure in the matrix to tensile and shear failure in the interphase as a function of the fibre-interphase modulus ratio. In particular, a significant increase in the load transfer efficiency in metal-matrix composites is found, for an interphase modulus E i less than the matrix modulus E m. Better load transfer properties in metal-matrix composites cause the yield point to occur at higher values of applied strain, and hence may significantly increase the toughness (area under the stress-strain curve) for certain metal-matrix composites. The computer results are compared with the predictions of Cox's shear-lag theory as well as with a new theoretical development presented in this work. The new theory is found to provide a better description of the fibre and matrix stress distribution.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
M. R. Piggott, in “Load Bearing Fibre Composites” (Pergamon, Oxford, 1980).
M. J. Owen, in “Fracture and Fatigue”, edited by L. J. Broutman (Academic, New York, 1974) p. 341.
J.-H. Kim and Y.-W. Mai, Compos. Sci. Tech. 41 (1991) 333.
E. Mäder and K. H. Freitag, Composites 21 (1990) 397.
J. P. Favre and J. Perrin, J. Mater. Sci. 7 (1972) 1113.
J. P. Favre and M. C. Merriene, Int. J. Adhesion Adhesives 1 (1981) 311.
L. Ongchin, W. K. Olender and F. H. Ancker, in 27 Ann. Tech. Comp. SPI, Section 11A (1972) 27.
V. Rao and L. T. Drzal, Polym. Compos. 12 (1) (1991) 48.
B. Miller, P. Muri and L. Rebenfeld, Compos. Sci. Tech. 28 (1987) 17.
J. F. Mandell, D. H. Grande, T.-H. Tsiang and F. J. McGarry, in Proceedings of 7th International Conference on Composite Materials (American Society for Testing and Materials, Philadelphia, 1986) p. 87.
H. C. Tsai, A. M. Arocho and L. W. Gause, Mater. Sci. Engng A126 (1990) 295.
M. K. Tse, SAMPE J. 21 (5) (1985) 11.
P. Herrera-Franco, W.-L. Wu, M. Madhukar and L. T. Drzal, in Proceedings of 46th Annual Conference of Composites Institute (Society of the Plastics Industry, 1991) p. 18.
M. R. Piggott, in Proceedings of 36th International SAMPE Symposium (1991) p. 1773.
I. Verpoaest, M. Desaeger and R. Keunings, in “Controlled Interphases in Composite Materials”, Proceedings of 3rd International Conference on Composite Interfaces (ICCI-III), edited by Hatsuo Ishida (Cleveland, Ohio, 1990) p. 653.
M. R. Piggott, Compos. Sci. Tech. 30 (1987) 295.
T. F. Cooke, J. Polym. Engng 7 (1987) 197.
G. J. Spies, J. Aircraft Eng. 25 (1953) 64.
J. J. Bikerman, J. Appl. Phys. 28 (1957) 1484.
N. Aravas, K. S. Kim and M. J. Loukis, Mat. Sci. Engng A107 (1989) 159.
K. S. Kim and N. Aravas, Int. J. Solid Struct. 24 (1988) 417.
K. Kendall, J. Adhesion 5 (1973) 105.
M. Nardin and J. Schultz, C. R. Acad. Sci. Paris, 311 (II) (1990) 613.
E. M. Asloun, M. Nardin and J. Schultz, J. Mater. Sci. 24 (1989) 1835.
H. L. Cox, Br. J. Appl. Phys. 3 (1952) 72.
K. Kendall, J. Mater Sci. 10 (1975) 1011.
B. W. Rosen, in “Fibre Composite Materials” (American Society for Metals, Ohio, 1965).
N. F. Dow, Report TIS R635D61 (General Electric Co.,1963).
W. Rosen, AIAA J. 2 (1964) 1985.
A. Kelly and G. J. Davies, Metall. Rev. 10 (37)(1965).
W. R. Tyson and G. J. Davies, Br. J. Appl. Phys. 16 (1965) 199.
M. R. Piggott, Acta Metall. 14 (1966) 1429.
H. D. Wagner and A. Eitan, Appl. Phys. Lett. 56 (1990) 1965.
N. C. Remedios and W. G. Wood, J. Compos. Mater. 2 (1968) 517.
A. S. Carraron and F. J. McGarry, 2 (1968) 222.
J. Harner and N. Ashbaugh, Technical Report USAAVLABS-TR-67-66, AD-66790 (Wittaker Corporation, 1968).
G. C. Shih and L. J. Ebert, J. Compos. Mater. 21 (1987) 207.
Y. Termonia, J. Mater. Sci. 25 (1990) 103.
P. S. Theorcaris, J. Appl. Polym. Sci. 30 (1985) 621.
, “The Mesophase Concept in Composites” (Springer, New York, 1987).
M. Narkis, E. J. H. Chen and R. B. Pipes, Polym. Compos. 9 (1988) 245.
L. Monette, M. P. Anderson, S. Ling and G. S. Grest, J. Mater. Sci. 27 (1992) 4393.
D. Hull, in “An Introduction to Composite Materials” (Cambridge University Press, Cambridge, 1981).
D. M. Schuster and E. Scala, Trans. Met. Soc. AIME 230 (1965) 1491.
P. S. Theorcaris and G. C. Papanicolaou, Fibre Sci. Technol. (1979) 421.
S. K. Chaturvedi and G. Y. Tzeng, Compos. Engng 1 (1991) 49.
R. B. Clough, F. S. Biancaniello, H. N. G. Wadley and U. R. Kattner, Met. Trans. 21A (1990) 2747.
A. Lustiger and D. Wagner, Private communication 8 (1991).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Monette, L., Anderson, M.P. & Grest, G.S. Effect of interphase modulus and cohesive energy on the critical aspect ratio in short-fibre composites. JOURNAL OF MATERIALS SCIENCE 28, 79–99 (1993). https://doi.org/10.1007/BF00349037
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF00349037