Abstract
As per the recent advancements in automotive sectors and use of intelligent systems with high speed communication, the sector is moving towards the standardizations in not only components used in automotives but also the sector is rapidly moving towards the standardizations in the protocols. Industry demands rapid application prototyping and simulations of the protocols to save time, money and energy. This paper focuses the light scattering study of popular protocols and simulators used in automotive sector. Paper also summarizes the problems reported due to wiring harness in automotives. The examples based on CAN data transfer and reception periodically observed through VNT from Math-Works. Protocols like Controller Area Network, Local Area Network, Flex Ray and high speed standards like M.O.S.T. are being used in distributed architecture. Also instead of implementing the protocols directly on hardware because it takes time for design, development and testing of same with increase in development cost. Also to resolve this issue and due to demand in industries, various simulators came into existence for rapid design, development and testing of the in vehicle networks. The simulators like BUSMASTER, CANoe, RTaW, VNT in Mat-lab is playing a vital role.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Leen, G., Heffernan, D.: Expanding automotive electronic systems. IEEE Comput. 35(1) (2002)
Navet, N., Simonot-Lion, N.: A review of embedded automotive protocols, April 14, 2008
“Overview of Current Automotive Protocols,” Vector CAN tech Inc., 2003. www.vectorcantech.Com (2003)
Automotive Handbook, Bentley Publishers, pp. 1092–1097 (2007)
Introduction to In-Vehicle Networking: Generic Protocols (2007)
The Seven Sins of, Wire Harness Assembly, DVD-60C, Association Connecting Electronics Industries
Home page of automotive softing. https://automotive.softing.com/en/standards/bus-systems.html. Accessed on 24 October 2018
Home Page of http://www.rfwireless-world.com/Terminology/LIN-vs-CAN-vs-FlexRay-vs-MOST.html. Accessed on 24 October 2018
Sawant, A. et al.: CAN, FlexRay, MOST versus ethernet for vehicular networks. Int. J. Innov. Adv. Comput. Sci. IJIACS 7(4) (2018). ISSN 2347-8616
Arun, J.K., Jagannathan, S. et al.: ABS with electronic stability control using MEMS and CAN protocol. Int. J. Emerg. Technol. Comput. Sci. Electron. (IJETCSE) 13(4) (2015). ISSN 0976-1353
CAN Distributed Embedded Systems Philip Koopman October 19, 2015 Significant material drawn from a presentation by Siemens Corp. “CANPRES 2.0, Oct 1998
Bosch. “CAN Specification version 2.0”. Robert Bosch GmbH, 30 02 40, D-70442 Stuttgart (1991)
Wei, C., Zhuang, Z., Tam, H., Ho, S.L., Al-Shamma’a, A.I., Shaw, A.: A CAN network for temperature monitoring of car engine and train Bogie. In: 2011 International Conference on Internet Computing and Information Services (2011)
Audsley, N.C.: Optimal priority assignment and feasibility of static priority tasks with arbitrary start times. Technical Report YCS 164, Dept. Computer Science, University of York, UK, Dec 1991
Road Vehicles—interchange of digital information—controller area network (CAN) for high-speed communication, ISO Standard-11898, International Standards Organization (ISO), Nov 1993
Liu, M. et al.: Schedulability analysis of multi-frame messages over controller area networks with mixed-queues. M¨alardalen University, Sweden, 978-1-4799-0864-6/13/$31.00 ©2013 IEEE
Home page of RTaW http://www.realtimeatwork.com/software/rtaw-sim/. Accessed on 04 December 2018
Home page of GIT Hub https://raw.githubusercontent.com/rbei-etas/busmaster-documents/master/help.pdf. Accessed on 24 November 2018
Home Page of https://www.cancia.org/fileadmin/resources/documents/proceedings/2012_lorenz.pdf. Accessed on 8 November 2018
Homepage of etas https://www.etas.com/download-center-files/products_Analyzers/BUSMASTER_Flyer_EN.pdf. Accessed on 24 November 2018
Cheon, B., Jeon, J.W.: The CAN FD network performance analysis using the CANoe. IEEE ISR 2013 (2013). https://doi.org/10.1109/isr.2013.6695598
Li, Y., Liyuan, T., Xiaochuan, T.: Simulation for vehicle comfort system based on CAN bus. In: International Conference on Computer, Mechatronics, Control and Electronic Engineering (2010). https://doi.org/10.1109/cmce.2010.5610342
Rishvanth et al.: Design of an in-vehicle network using LIN, CAN and FlexRay, gateway and its diagnostics using vector CANoe. Am. J. Sig. Process. (2011)
Home page of http://www.oalib.com/search?kw=%20Lin%20KJ. Accessed on 24 October 2018
Building CANS Communication using Simulink models in Matlab R-15, Examples from Documentation
Li, F., Wang, L., Liao, C.: CAN bus communication system based on Matlab/Simulink. In: 2008 4th International Conference on Wireless Communications, Networking and Mobile Computing (2008). https://doi.org/10.1109/wicom.2008
Acknowledgements
We consider it a great pleasure to express our deep sense of gratitude to KBC North Maharashtra University, Maharashtra, India and Mathworks Corporation.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Pawar, U.B., Bhirud, S.G., Kolhe, S.R. (2020). Light Scattering Study on Protocols and Simulators Used in Automotive Application(s). In: Iyer, B., Deshpande, P., Sharma, S., Shiurkar, U. (eds) Computing in Engineering and Technology. Advances in Intelligent Systems and Computing, vol 1025. Springer, Singapore. https://doi.org/10.1007/978-981-32-9515-5_16
Download citation
DOI: https://doi.org/10.1007/978-981-32-9515-5_16
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-32-9514-8
Online ISBN: 978-981-32-9515-5
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)