Abstract
Development of automated machining robots has gained momentum with many well-known processes realizing automation to improve quality and increase efficiency. However, grinding process is difficult to automate. High temperature at the contact between the grinding wheel and the workpiece is the source of thermal deformation and phase transformations which can lead to thermal damage and affect surface integrity. This study aims to achieve a better understanding of the thermal behaviour of the grinding process in order to develop an automated grinding robotic system. We studied the thermal behaviour of Inconel 718 workpiece during the grinding process. Different models have been established previously to characterize the heat generation and dispersion at the interface between grinding wheel and workpiece. The Rowe model is used to calculate the heat escaping from the workpiece, by convection, and convection with the grinding wheel in order to obtain the heat remaining in the workpiece. Once the heat source intensity is calculated, Jaeger’s model for moving heat sources is used to calculate the evolution of the temperature along the length of a bar being ground and along the depth in steady state. A numerical model is created using ABAQUS to take into account non-linearity such as the temperature dependence of the parameters and complex boundary conditions. An experiment is carried out on an Inconel 718 bar to compare with the analytical and numerical results. The results show that the boundary condition and the temperature dependence properties of Inconel 718 cannot be neglected. The temperature profiles obtained by the numerical model, which includes the boundary condition and temperature dependence properties of material, are more consistent with the experimental results.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Shaw MC, Ramanath S (1988) Abrasive grain temperature at the beginning of a cut in fine grinding. J Eng Ind 110(1):15–18
Outwater LO (1952) Surface temperatures in grinding. Trans ASME 74:73–78
Malkin S (1985) Current trends in CBN grinding technology. CIRP Ann Manuf Technol 34(2):557–563
Malkin S, Guo C (2007) Thermal analysis of grinding. CIRP Ann 56(2):760–782
Kohli S, Guo C, Malkin S (1995) Energy partition to the workpiece for grinding with aluminum oxide and CBN abrasive wheels. J Eng Ind 117(2):160–168
Rowe WB, Pettit JA, Boyle A et al (1988) Avoidance of thermal damage in grinding and prediction of the damage threshold. CIRP Ann Manuf Technol 37(1):327–330
Rowe WB, Black SCE, Mills B et al (1997) Grinding temperatures and energy partitioning. Proc Math Phys Eng Sci 453(1960):1083–1104
Rowe WB (2013) Principles of modern grinding technology. William Andrew, New York
Saini DP, Brown RH (1980) Local elastic deflection in grinding. Ann CIRP 29(1):189–194
Verkerk J (1975) The real contact length in cylindrical plunge grinding. Ann CIRP 24:259
Gu DY, Wager JG (1988) New evidence on the contact zone in grinding—contact length, sliding and cutting regions. CIRP Ann Manuf Technol 37(1):335–338
Zhou ZX, van Lutterwelt CA (1992) The real contact length between grinding wheel and workpiece—a new concept and a new measuring method. CIRP Ann Manuf Technol 41(1):387–391
Lavine AS, Jen TC (1991) Thermal aspects of grinding: heat transfer to workpiece, wheel, and fluid. J Heat Transfer 113(2):296–303
Guo C, Malkin S (2000) Energy partition and cooling during grinding. J Manuf Process 2(3):151–157
Tkaya MB, Mezlini S, El Mansori M et al (2009) On some tribological effects of graphite nodules in wear mechanism of SG cast iron: finite element and experimental analysis. Wear 267(1):535–539
Rowe WB, Black SCE, Mills B et al (1995) Experimental investigation of heat transfer in grinding. CIRP Ann Manuf Technol 44(1):329–332
Brosse A, Naisson P, Hamdi H et al (2008) Temperature measurement and heat flux characterization in grinding using thermography. J Mater Process Technol 201(1–3):590–595
Li B, Zhu D, Pang J et al (2011) Quadratic curve heat flux distribution model in the grinding zone. Int J Adv Manuf Technol 54(9–12):931–940
Lavisse B, Lefebvre A, Sinot O et al (2017) Grinding heat flux distribution by an inverse heat transfer method with a foil/workpiece thermocouple under oil lubrication. Int J Adv Manuf Technol 92(5–8):2867–2880
Guo C, Malkin S (1996) Inverse heat transfer analysis of grinding, part 1: methods. J Eng Ind 118(1):137–142
Li HN, Axinte D (2017) On a stochastically grain-discretised model for 2D/3D temperature mapping prediction in grinding. Int J Mach Tools Manuf 116:60–76
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Ren, X., Soulard, B., Wang, J., Xu, Y., Chen, X. (2019). Thermal Analysis of Belt Grinding Process of Nickel-Based Superalloy Inconel 718. In: Chen, S., Zhang, Y., Feng, Z. (eds) Transactions on Intelligent Welding Manufacturing. Transactions on Intelligent Welding Manufacturing. Springer, Singapore. https://doi.org/10.1007/978-981-13-8668-8_3
Download citation
DOI: https://doi.org/10.1007/978-981-13-8668-8_3
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-13-8667-1
Online ISBN: 978-981-13-8668-8
eBook Packages: Intelligent Technologies and RoboticsIntelligent Technologies and Robotics (R0)