Abstract
At a certain point in its life cycle, a product will reach a condition where it partly or completely loses its functionality. When this happens, the disassembly has the ambition to regenerate a product-value or to enable an environmental friendly product recycling. With regard to the high workload and costs for manual labor one approach to increase the productivity of disassembly tasks is the use of automated disassembly systems (ADS). Depending on different life cycle scenarios, requirements on automated disassembly systems vary. Concerning this problem, a general methodology is developed, which enables the determination of a conceptual ADS by assigning automated modules that are processing the product disassembly. In the first place the objective of a disassembly is determined, followed by a closer investigation of the product. Thereby target components are defined, which has to disassembled. By looking at the connections between these target components suitable separation procedures are derived. Finally, modules of the automated disassembly system are determined.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Preview
Unable to display preview. Download preview PDF.
Similar content being viewed by others
References
[1] Duflou, JR; Seliger, G; Kara, S; Umeda, Y; Ometto, A; Willems, B (2008) Efficiency and feasibility of product disassembly: A case-based study. CIRP Annals – Manufacturing Technology 57(2): 583-600
[2] Seliger; G (2007) Sustainability in Manufacturing – Recovery of Resources in Product and Material Cycles. Berlin, Springer Berlin Heidelberg New York
[3] Hesselbach, J., Hermann, C., Luger, T. (2007) Sustainability in Manufacturing – 3.4 Assessment of Recyclability. Berlin, Springer Berlin Heidelberg New York
[3] Gungor, A; Gupta, SM (1998) Disassembly sequence planning for products with defective parts in product recovery. Computers & Industrial Engineering 35(1-2): 161-164
[4] Seliger, G; Keil, T; Rebafka, U; Stenzel, A (2001) Flexible Disassembly Tools. Proceedings of the 2001 IEEE International Symposium on Electronics and the Environment 30-35
[5] Kim, HJ; Kernbaum, S; Seliger, G (2009) Emulation-based control of a disassembly system for LCD monitors. The International Journal of Advanced Manufacturing Technology 40: 383-392
[6] Vongbunyong, S; Chen, WH (2015) Disassembly Automation – Automated Systems with Cognitive Abilities. Cham: Springer International Publishing
[7] Ohlendorf, M., Herrmann C., Jürgen Hesselbach (2004) Simulation-based disassembly systems design, Proc. SPIE 5262, Environmentally Conscious Manufacturing III, 94
[8] O’Shea, B; Kaebernick, H; Grewal SS; Perlewitz, H; Müller, K; Seliger, G (1999) Method for automatic tool selection for disassembly planning, Assembly Automation 19(1): 47-54
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2017 Springer-Verlag GmbH Deutschland
About this paper
Cite this paper
Wolff, J., Kolditz, T., Günther, L., Raatz, A. (2017). Development of a Methodology for the Determination of Conceptual Automated Disassembly Systems. In: Schüppstuhl, T., Franke, J., Tracht, K. (eds) Tagungsband des 2. Kongresses Montage Handhabung Industrieroboter. Springer Vieweg, Berlin, Heidelberg. https://doi.org/10.1007/978-3-662-54441-9_9
Download citation
DOI: https://doi.org/10.1007/978-3-662-54441-9_9
Published:
Publisher Name: Springer Vieweg, Berlin, Heidelberg
Print ISBN: 978-3-662-54440-2
Online ISBN: 978-3-662-54441-9
eBook Packages: Computer Science and Engineering (German Language)