Abstract
Aflatoxins are produced by filamentous fungi, primarily Aspergillus flavus, A. parasiticus, and A. nomius. These fungi occur naturally and might infest several food commodities throughout the food chain. The four major aflatoxins are Aflatoxin B1 (AFB1), Aflatoxin B2 (AFB2), Aflatoxin G1 (AFG1), and Aflatoxin G2 (AFG2). Aflatoxin M1 (AFM1) and Aflatoxin M2 (AFM2), the hydroxylated metabolites of AFB1 and AFB2, respectively, are excreted into the milk of mammals that have ingested contaminated feed. Aflatoxins are highly carcinogenic, teratogenic, and hepatotoxic to humans and animals; consequently, knowledge about their incidence and levels in food and feed is a matter of public health concern. Numerous countries have set specific regulations on the maximum permitted limits of these contaminants in foodstuffs. Therefore, identifying and quantifying aflatoxins by reliable analytical methods are paramount for compliance with these legal limits. This chapter presents the fundamentals and recent developments of sample extraction, cleanup procedures, and identification and quantification approaches for aflatoxins in food and feed.
Access provided by Autonomous University of Puebla. Download chapter PDF
Similar content being viewed by others
Keywords
- Aflatoxins
- Sample extraction
- Immunoaffinity column
- SPE
- QuEChER
- DLLME
- Liquid chromatography
- Thin-layer chromatography
- Fluorescence
- Mass spectrometry
- ELISA
- Method validation
- Multiclass mycotoxin
8.1 Introduction
Before the 1960s, episodes of farm livestock intoxication due to consumption of moldy feed had been described, but back then these episodes were not further investigated and remained unexplained (Richard 2008). However, in May 1960, after the acute poisoning of turkeys named Turkey “X” Disease in the United Kingdom, the correlation between an unknown toxin produced by fungus in the feed and its toxic effects was finally recognized (Sargeant et al. 1961; Lancaster et al. 1961). Shortly afterward, the unknown toxin was demonstrated to be carcinogenic to rats; it was also linked with liver cancer in humans (Le Breton et al. 1962). Chemical and physical characterization of the toxin, termed aflatoxin, was only accomplished some years later (Van der Zijden et al. 1962; Asao et al. 1963; Wogan 1966). Actually, aflatoxins belong to a larger group of toxic substances known as mycotoxins, which are produced by diverse fungi. Since the aflatoxins were characterized, scientists worldwide have scrutinized them, particularly in studies related to their synthesis and incidence in food and feed, adverse effects on human and animal health, and mitigation strategies (Rushing and Selim 2019).
Aflatoxins are produced by filamentous fungi, primarily Aspergillus flavus, A. parasiticus, and A. nomius (Olsen et al. 2008). Emericella astellata, E. venezuelensis, A. bombycis, A. ochraceoroseus, A. pseudotamari, and A. tamarii also produce aflatoxins; however, these fungi are less common in crops. All the aforementioned fungi occur naturally and might infest several food commodities throughout the food chain: before and during harvesting; during storage, transportation, or processing; and even during consumption (Kaale et al. 2021). Groundnuts, cereals, oilseeds, and spices grown in tropical and subtropical regions under hot and humid climate conditions are the most susceptible to contamination (Williams et al. 2004).
Presently, around twenty aflatoxins have been characterized. The four major aflatoxins are Aflatoxin B1 (AFB1), Aflatoxin B2 (AFB2), Aflatoxin G1 (AFG1), and Aflatoxin G2 (AFG2). Aflatoxin M1 (AFM1) and Aflatoxin M2 (AFM2), the hydroxylated metabolites of AFB1 and AFB2, respectively, are also important: they are excreted into the milk of mammals that have ingested contaminated feed (Marchese et al. 2018). AFB1 has been the most investigated and is the most prevalent in food and feed.
Aflatoxins are a group of difuranocoumarin derivatives (Fig. 8.1). AFB1 and AFB2 consist of a difuran ring fused to a coumarin nucleus with a pentenone ring; AFG1 and AFG2 contain a six-membered lactone ring instead of a pentenone ring (Dhanasekaran et al. 2011). Aflatoxins are insoluble in nonpolar solvents, very slightly soluble in water, and freely soluble in moderately polar solvents (e.g., methanol, acetone, chloroform, and dimethyl sulfoxide). AFB1 and AFB2 emit intense blue fluorescence under UV light, whereas AFG1 and AFG2 emit yellow-green fluorescence, hence the designations B and G, respectively (Antila et al. 2002). Ultraviolet (UV) light in the presence of oxygen, extreme pH values (<3 or >10), and oxidizing and chlorinating agents degrade aflatoxins (Budavari et al. 2001). Aflatoxins have high thermal stability, which prevents them from being degraded in heat treatments during food processing. Table 8.1 summarizes some physical and chemical properties of aflatoxins (Zhang and Banerjee 2020).
In 1987, over two decades after AFB1 was discovered and extensively investigated, the International Agency for Research on Cancer (IARC) classified it as Group 1 carcinogen (Antilla et al. 2002). Furthermore, AFB1 is the most harmful and lethal among naturally occurring carcinogens. Another reason for IARC classifying AFM1 as Group 1 is its association with immunosuppression, genotoxicity, mutagenicity, teratogenicity, and carcinogenicity (Womack et al. 2016).
As knowledge about the adverse effects of aflatoxins on human health evolved over the years, many countries set specific regulations on the maximum permitted limits of these contaminants in foodstuffs. As a general rule, the limits established for animal feed are usually higher than the limits set for food intended for direct human consumption.
The European Community legislation is undoubtedly the strictest and the most comprehensive regarding aflatoxins (European Commission 2006a). This legislation sets maximum levels not only for the sum of AFB1, AFB2 AFG1, and AFG2 (ΣAF), as listed in most countries, but also for AFB1 individually. Maximum AFB1 and ΣAF levels of 2.0 and 4.0 μg kg−1, respectively, are allowed for groundnuts, nuts, dried fruits, and all cereals intended for direct human consumption. If further treatment is applied, AFB1 and ΣAF levels in groundnuts must not exceed 8.0 and 15 μg kg−1, respectively. Higher AFB1 and ΣAF maximum levels, 5.0 and 10 μg kg−1, respectively, are acceptable for nuts, dried fruits, and maize that are processed before human consumption or used as a food ingredient. The most restricted limit of 0.1 μg kg−1 AFB1 is set for dietary food for particular medical purposes, cereal-based food, and baby food intended for infants and young children. Concerning animal feed, only AFB1 is regulated (European Commission 2003). The maximum limit of 20 μg kg−1 AFB1 is obligatory for all feed components and complete feedingstuff for cattle, sheep, goats, swine, and poultry, while 10 μg kg−1 AFB1 is set for complete feedingstuff for calves and lambs. Feed for dairy animals has the lowest permitted level of 5 μg kg−1 AFB1.
Legal limits adopted by the US Food and Drug Administration (US FDA) are more general and specify only levels for the sum of aflatoxins (ΣAF). A range between 100 and 300 μg kg−1 ΣAF is defined for grains intended for beef cattle, swine, and poultry depending on the maturity stage. Up to 20 μg kg−1 ΣAF is acceptable for animal feed other than corn and cottonseed meal, which includes grains intended for immature and dairy animals and human food (Jimenez Medina et al. 2021).
Asian countries do not have a harmonized regulation, and the maximum limits adopted there may vary considerably among countries (Anukul et al. 2013). Maximum ΣAF limits might be as high as 30 μg kg−1 for all food, as defined in India and Sri Lanka, or 35 μg kg−1 in Indonesia and Malaysia. Japan sets the ΣAF limit of 10 μg kg−1 for all food, and the AFB1 limit of 10 and 5 μg kg−1 for rice and other grains, respectively. China regulates AFB1 in corn and corn products and peanuts and peanut products at 20 μg kg−1. Also, Chinese regulation lays down maximum AFB1 limits of 10 μg kg−1 for rice and vegetable oils, except peanut and corn oils, and of 5 μg kg−1 for wheat, barley, beans, and other grains. For condiments, such as soy sauce, vinegar, and fermented paste that use grains as primary materials, the maximum AFB1 value is 5 μg kg−1. The lower AFB1 limit of 0.5 μg kg−1 is set for food intended for particular dietary uses, like formula food and complementary food for infants and young children. South Korea sets the AFB1 limit of 10 μg kg−1 for grains, cereal products, dried fruits, streamed rice, and dried fermented soybeans. The lower AFB1 limit of 0.1 μg kg−1 is set for baby food. Only Indonesia regulates ΣAF at 50 μg kg−1 for corn feed.
In 2011, the Brazilian National Health Surveillance Agency (ANVISA) reviewed regulations for mycotoxin, and maximum limits for aflatoxins that had previously been stated only for peanut, peanut butter, corn, and its derivatives were extended to various grains and other food items (ANVISA 2011). ΣAF concentrations in peanut, peanut butter, corn, and some spices must not surpass 20 μg kg−1. The maximum tolerable ΣAF limit of 5 μg kg−1 is set for beans, chocolate, cocoa products, and grains except for corn. Cereal-based food and infant formulas for young children must have a maximum ΣAF limit of 1 μg kg−1.
Regulations worldwide consider not only food (e.g., groundnuts) that may frequently be more contaminated with known aflatoxin-producing fungi, but also foodstuffs that are mainly applied as staple food, which are the primary source of nutrients and energy. There is also a relationship with the culture and eating habits of each country or region. For instance, there are special regulations for rice in Japan and China; corn, rice, and beans in Brazil; and dried fermented soybeans in South Korea because these are everyday food items in these countries.
AFM1 essentially contaminates milk and dairy products. Given that children widely consume these products, several countries have specific regulatory limits for this toxin. The European Community has the lowest permitted AFM1 level – 0.050 μg kg−1 – for raw milk, heat-treated milk, and milk for manufacture of milk-based products (European Commission 2006a). An even lower limit – 0.025 μg kg−1 – is fixed for infant formulas and dietary food for particular medical purposes intended for infants. The United States, Brazil, China, Indonesia, Philippines, Singapore, South Korea, and Taiwan permit 0.5 μg kg−1 AFM1 for milk (ANVISA 2011; Jimenez Medina et al. 2021).
Finally, numerous developing countries do not have regulations for aflatoxins. Consequently, the population is vulnerable and is likely to consume inappropriate food (Ayelign and De Saeger 2020). Besides variance in consumer exposure and safety, all the divergences discussed in the previous paragraphs might severely impair the international trade of food commodities. In this scenario, it is important to identify and to quantify aflatoxins for compliance with these legal limits.
8.2 Fundamentals of Analytical Methods
Analytical chemistry is fundamental in countless areas. With respect to food safety, analytical methods are indispensable to confirm adulterations and to identify and to quantify xenobiotics that are harmful to human and animal health. The first and most essential decision regarding quantitative analysis is selecting the method. This choice is frequently complex and requires experience on the part of the analyst. Moreover, the required accuracy must be considered. Unfortunately, high reliability almost always demands considerable time and resources. The second decision concerns defining the number of samples, which also involves considering time and resources. Instrumental analysis might be an option if the number of samples is large, but reasonable time is spent on preliminary operations, such as assembling and calibrating instruments and preparing standard solutions. If the number of samples is small, an analytical method that dismisses the need for preliminary steps may be the best choice. Finally, the complexity of the sample and the number of components to be quantified also defines which method will be selected. Various analytical methods are available to determine aflatoxins. Because many countries have regulatory limits, analytical methods established by collaborative studies involving several laboratories or adopted by international organizations should be preferred, thus allowing analytical results to be compared. After validation according to international guidelines, new methods developed for analysis of aflatoxins are likely to become widely accepted in studies on the incidence of these toxins in food and human exposure to them (Berthiller et al. 2017).
The next decision regards sampling, which might be the most significant source of error. Sampling involves collecting a portion of the analyzed material; the composition of this portion must closely represent the entire material being sampled. The analyst must ensure that the laboratory sample is representative and must protect it from contamination and changes in composition before analysis. Contamination with aflatoxins originates from fungal metabolism and might not occur evenly throughout the sample, which poses an additional challenge (Wesolek and Roudot 2016). The European Commission regulation 401/2006 includes guidelines and plans for sampling mycotoxins, so that reliable qualitative and quantitative results can be achieved (European Commission, 2006b). Detailed discussion about sampling is beyond the scope of this chapter, but one must be aware of standard procedures before conducting a study (Galaverna and Dall'Asta 2012).
Processing the sample is another step in an analysis. Aflatoxins are determined in many solid samples, mainly grains, and a grinding step is mandatory before the analytical sample is removed. First, a solid sample is ground or milled, to reduce particle size. Then, it is mixed, to ensure homogeneity. After that, it is stored for some time before analysis. Zhang and Banerjee (2020) described dry, wet, and cryogenic grinding for analysis of aflatoxins in diverse food matrixes. The dry grinding protocol is extensively used to obtain homogeneous particle size for miscellaneous commodities like corn, wheat, peanuts, groundnuts, dried fruits, and spices (Spanjer et al. 2008). Although only dry grinding devices are available in most labs, and even though samples with bulky sizes must be handled or samples might contain high sugar or fat content, this type of grinding might cause obstruction or melting due to heat generated by the blades. An alternative is to turn to wet grinding, which provides samples with smaller particle sizes and uniform distribution of aflatoxins, but it is laborious and time-consuming (Spanjer et al. 2006). Wet grinding consists of mixing a sample with water or other solvents before the blending process, to form a slurry that provides test portions with better particle distribution and reproducibility than the test portions from samples processed by dry grinding. Lastly, cryogenic milling allows heat-sensitive samples, typically fatty food, to be ground in teeny particle sizes (Liao et al. 2013). Cryogenic grinding requires that samples be frozen overnight and demands special milling devices and liquid nitrogen or dry ice as freezing agent. Compared to dry and wet milling, cryogenic grinding preserves the physical composition of samples. Many labs prefer using dry milling on a routine basis and only apply wet or cryogenic grinding to food matrixes that are unsuitable for dry milling.
Most analytical methods employ solutions of samples prepared in a suitable solvent. Ideally, the solvent should completely dissolve the analyte as fast as possible. The dissolution and extraction conditions must be sufficiently mild to prevent the analyte from being lost (Fifield and Kealey 2000). Many researchers have focused on the procedures and optimized conditions for efficiently dissolving and extracting aflatoxins from food and feed given that this is a decisive step for analysis of residual amounts of toxins. The choice of and the actual need for an extraction and purifica technique is closely related to the selected analytical method. If the analytical method is highly selective, purification may not be as extensive. On the other hand, if the analytical method cannot determine low concentrations like those found in samples, pretreatment must also pre-concentrate the analyte that will be later measured.
Once analytes are in solution, the next step eliminates any substances present in the sample that may interfere in the measurement, which frequently results in enrichment of the analyte. Interferent is any compound other than the analyte that affects the measurement. Few of the physical properties that are used to measure and to quantify an analyte are unique to a single chemical substance. In contrast, the measured properties are characteristic of a group of elements or substances. Initially, only absorption and fluorescence emission were employed to measure aflatoxins. Unfortunately, other substances from food matrixes also exhibit the same behavior. No fast and straightforward rules for eliminating interferents exist, and solving this problem may be the most critical aspect of analysis after sampling. Therefore, eliminating interferents to quantify aflatoxins has also been investigated. A crucial challenge is the diverse composition of the sample, which may contain fat, proteins, and carbohydrates as major components, comprising assorted substances that might interfere in the measurement. An ideal analytical method should determine many analytes in several matrixes while maintaining the same performance.
After interferents are eliminated, there is usually an intermediate step that is fundamentally represented by chromatographic separation techniques. Analysis of aflatoxins cannot be discussed without mentioning the first of all separation techniques, thin-layer chromatography (TLC). The years following the discovery of aflatoxins were also accompanied by the development of high-performance liquid chromatography (HPLC) and, lately, ultra-high-performance liquid chromatography (UHPLC). Chromatographic separation is not mandatory when it comes to identifying and quantifying aflatoxins, but it is undoubtedly available in most laboratories that determine these contaminants in food and feed.
Given that the analytical results depend on measuring a physical or chemical property of an analyte, this property must vary in a known and reproducible way as a function of the concentration of the analyte. Early methods employed the natural ultraviolet absorbance or fluorescence emission of aflatoxins as a powerful identification and quantification tool. Indeed, these properties are still widely used and recommended by official protocols. In turn, combining HPLC or UHPLC with mass spectrometry (MS) provides analytical chemists with a remarkable technique to characterize and to quantify organic compounds.
Analytical results are incomplete without estimating reliability. Thorough method validation provides an analytical method with reliability and consistency (FDA 2019). Analytical validation is a quality assurance procedure that describes the conditions under which laboratory analysis are planned, performed, monitored, reported, and archived. Later, we will dedicate a topic to analytical validation parameters for identifying and quantifying aflatoxins in food and feed.
Knowledge about the presence of aflatoxins and their levels in food is a matter of public health concern. Therefore, one should not forget that many developing countries might lack resources for laboratory analysis and specialized personnel, maintenance, and supplies for high-tech instrumentation. On the other hand, resources for applying noninstrumental methods that can provide valuable data may be available. An important research area in analytical chemistry involves developing simple and inexpensive devices that can be used on-site and thus avoid that humans and animals consume contaminated and inappropriate food.
Developing analytical methods to determine aflatoxins goes hand in hand with knowledge about the presence of aflatoxins in food and their toxic effects. The greater the awareness and regulatory restrictions, the more selective and sensitive the analytical methods must be to meet these requirements. The general rule for analyzing almost any substance in food also applies to aflatoxins: extraction in a suitable solvent, elimination of interferents by a proper cleanup procedure, pre-concentration when necessary, and identification or quantification on the basis of a physical or chemical property.
8.3 Sample Extraction and Cleanup for Determination of Aflatoxins
After a solid sample is properly sampled and powdered or ground, an extraction step is practically unavoidable (Reiter et al. 2009). Frequently, over 80% of the time required for an analysis is spent on sample preparation and cleanup. Several methods to extract aflatoxins from food and feed, like liquid-liquid extraction (LLE), solid phase extraction (SPE), immunoaffinity columns (IACs), dispersive liquid-liquid microextraction (DLLME), and QuEChERS (Quick, Easy, Cheap, Effective, Rugged, and Safe), have been established and extensively revised (Turner et al. 2009; Espinosa-Calderón et al. 2011; Zhang and Banerjee 2020; Miklós et al. 2020).
8.3.1 Liquid–Liquid Extraction
LLE is a classic and the oldest extraction technique. It is based on the solubility properties of the analytes in the aqueous or organic phase, or even in a system with two or more solvents. In the past, aflatoxins were primarily extracted by LLE because it was the only procedure available (Pons and Goldblatt 1965; Park and Melnick 1966). The first step entails extraction with methanol, acetone, chloroform, or a mixture of different polar organic solvents. Next, the extract is concentrated by evaporation. If necessary, a second extraction removes fats from the remaining residue by means of a polar and a nonpolar organic solvent such as hexane, cyclohexane, or petroleum ether. Some extractions include sodium chloride, which dissolves into the aqueous phase and increases its ionic force, facilitating extraction of aflatoxins into the organic phase, a process known as salting-out. A disadvantage of LLE is possible absorption of aflatoxins onto glassware, not to mention that LLE is a tedious, time-consuming procedure that requires large volumes of toxic solvents, which is not environmentally friendly.
Even though LLE is hardly sufficient to produce a clean extract to proceed with detection or quantification, some authors quantified aflatoxins in cereals, fish, spices, and beverages by using this extraction. Otta et al. (2000) extracted AFB1, AFB2, AFG1, and AFG2 from corn and wheat with a mixture of acetonitrile/water (9:1, v/v) and from fish with a mixture of methanol/water (7:3, v/v) on a vibrating shaker. The extracts were filtered, evaporated to dryness, and dissolved in dichloromethane/acetone (9:1, v/v), and the analysis was continued without any additional cleanup. Sheijooni-Fumani et al. (2011) quantified AFB1 in rice, chickpea, and lentil by employing a two-step LLE. Well-milled solid samples were extracted with methanol/water (8:10, v/v); after vigorous shaking for 30 min, the supernatant was extracted again with chloroform. Then, after centrifugation for 5 min, the settled extraction phase was dried; the residue was dissolved in methanol; and the analyte was quantified. García-Moraleja et al. (2015) extracted aflatoxins from coffee beverages by LLE. The samples were freeze-dried, and the residues were extracted with ethyl acetate/formic acid (95:5, v/v) in three 5-min cycles. The supernatants were evaporated to dryness and reconstituted in methanol/water (1:1, v/v) before analysis. Sailaja et al. (2018) reported that a single extraction with chloroform at room temperature was adequate to extract aflatoxins from red chili. The chloroform extracts were filtered, washed with distilled water, and dried with anhydrous sodium sulfate. After being concentrated almost to dryness, the residues were dissolved in chloroform. Kokkonen et al. (2005) extracted AFB1, AFB2, AFG1, AFG2, and AFM1 from cheese with acetonitrile acidified with 0.1% formic acid and defatted with hexane. The mixture was filtered, and an aliquot of the acetonitrile phase was evaporated to dryness and dissolved in methanol for later quantification.
Although LLE is a low-cost, widely applicable method, LLE extracts are not entirely free of interferents, and additional cleanup is frequently required (Kamimura et al. 1985). Given that further cleanup becomes inevitable, some methods include a purification step on a minicolumn filled with silica, florisil, or alumina, to purify the extract (Waltking 1970; Maia and Siqueira 2002). This has led to the well-recognized and commonly used SPE for analysis of aflatoxins
8.3.2 Solid-Phase Extraction
Samples can be purified by SPE, a process that has been available since the mid-1980s and which was developed as an alternative or supplement to LLE (Otles and Kartal 2016). SPE aims to reduce interference from components of the sample matrix and to improve detection sensitivity. The principle of purification is similar to that of solid-liquid chromatography. Sample separation, purification, and enrichment are mainly achieved by selective adsorption and desorption of components in the sample by a solid phase, placed inside a column or a disposable cartridge, which are widely commercially available. Commonly, two modes of SPE are employed: retention and elution of analytes or removal of interferents. The most usual method, which involves more steps, entails eluting the sample extract through the solid phase (adsorbent), to retain the analyte, followed by elution with a solvent of appropriate strength, to wash away impurities. Then, the analyte is eluted with a small volume of solvent, to achieve separation, purification, and concentration. Interfering impurities can also be selectively adsorbed while the analyte is allowed to elute, with cleanup comprising a single step. In addition, the SPE technique is a valuable tool for many purposes because it is versatile and might be optionally used in combination with other extraction techniques. Given that samples of food and feed designed for analysis of aflatoxins are solid, a single LLE usually precedes the SPE step, but purification and enrichment obtained in the latter step are much superior. Adsorbents that are used to purify extracts to determine aflatoxins are mostly prepared with C18, florisil, silica gel, or alumina, and countless other adsorbents for SPE are commercially available (Zhang and Banerjee 2020).
Successful applications of SPE to clean up diverse samples aiming at determining aflatoxins have been reported. Several parameters such as type and amount of sorbent, elution solvent, and previous extraction or dilution with proper solvents are constantly being reevaluated for each type of sample. Romero-Gonzales et al. (2009) analyzed AFB1, AFB2, AFG1, and AFG2 in beer by just eluting 10 mL of degassed samples through a C18 commercial cartridge. After washing the column with water, aflatoxins were eluted with acetonitrile/methanol (60:40, v/v). Minicolumns prepared in-house and filled with aluminum oxide efficiently purified extracts of various grains including cornmeal, cottonseed, peanuts, almonds, and pistachios in one step. Ground samples were extracted with methanol/water (80:20, v/v), filtered, and diluted (1:1, v/v) with acetonitrile. The previous mixture was eluted through the columns. The purified extract was collected and directly injected into a LC system. Compared with other available commercial cartridges, these minicolumns allowed substantial savings (Sobolev and Dorner 2002). The same authors also showed that florisil adsorbed aflatoxins selectively in polar solvents (Sobolev 2007). Raw almonds, Brazil nuts, walnuts, hazelnuts, brown and white rice, cornmeal, and dry-roasted pistachio nuts were first extracted in methanol/water (80:20, v/v). After a sequential wash with methanol/water (60:40, v/v), methanol, and chloroform/methanol (90:10, v/v), to remove impurities, aflatoxins were released from the column with acetone/water/formic acid (96:3.7,0.3, v/v). Sep-Pak Silica and Oasis HLB WatersTM were used to clean up extracts of cooked rice and medicinal herbs, respectively (Park and Kim 2006; Ventura et al. 2004).
8.3.3 Immunoaffinity Columns
IACs might be considered a subtype of SPE columns. IACs contain antibodies immobilized on inert support beads that exclusively retain aflatoxins (Ertekin et al. 2019). Due to their high specificity, IACs produce cleaner extracts with lower level of interfering matrix components than the less selective solid phases of SPE sorbents. IACs have been extensively applied because they are well established for cleaning up and concentrating sample extracts for analysis of aflatoxins (Scott and Trucksess 1997; Patey et al. 1991).
IACs are undoubtedly handy when a less selective detector is used, which is the case of ultraviolet or fluorescence detectors, and they have emerged as one of the most important sample preparation techniques. The processes involved in IACs are essentially the same as those described for SPE: the sample extract is eluted on the IAC, and the antibody retains aflatoxins. A sequential wash with water or buffer removes impurities, and aflatoxins are released by elution with an appropriate solvent, usually methanol, which breaks the aflatoxin-antibody bond. Several commercial IACs are available for AFB1, AFB2, AFG1, AFG2, and AFM1, but, unlike regular SPE cartridges, IACs are filled with phosphate-buffered saline (PBS) solution and kept refrigerated, to maintain the functionality of the antibody.
Another critical point in IAC development is the high content of solvents, such as acetonitrile, methanol, or acetone, in sample extracts: antibodies are not tolerant to high concentrations of organic solvents. Before being eluted through the column, extracts must be diluted with water or buffer. The problem is that this dilution increases the volume that has to be eluted and may yield insoluble compounds that interfere in the binding of aflatoxins to the antibodies (Uchigashima et al. 2009).
Despite the higher selectivity of IACs, special attention must be given to them when they are applied to food matrixes that have not been previously evaluated. Castegnaro et al. (2006) highlighted that some drawbacks of IACs must not be overlooked. Complex matrixes might contain unknown substances that obstruct the binding site of antibodies, thereby reducing the absorption of toxins and yielding inaccurate results. Furthermore, interaction with other substances might alter the structure of toxins, so antibodies will not recognize them.
IACs are manufactured for single extraction, and instructions clearly recommend that they be discarded after use. Unfortunately, many laboratories cannot afford their high cost, mainly when they are imported and purchased with foreign currency. This led numerous researchers to assess the reuse of different commercial columns, but results regarding aflatoxins and the composition of samples are not consistent among manufacturers. Liao et al. (2020) evaluated regenerating columns for raw malt extracts. They found that washing the IAC with PBS and stocking it at 4 °C overnight maintained IAC performance for nine additional extractions of AFB2, AFG1, and AFG2, but only two additional extractions of AFB1. Iha et al. (2017) also attempted to reuse IAC by immediately washing it with PBS and storing it at 8 °C overnight for re-equilibration, for use on the following day. A naturally contaminated peanut sample was extracted six times with the same column, and the results obtained for aflatoxins were statistically equivalent, except for AFG2. If only AFB1 was quantified, the same selectivity was maintained for ten consecutive extractions. Liu et al. (2012) used reconditioned IACs twice to extract aflatoxins from medicinal herbs. Nevertheless, they highlighted that if the column was dirty with pigments or ingredients that did not elute with water, it should not be reused due to poor analyte recovery.
Divergences among assessments clearly demonstrate that caution must be taken when reusing IACs from different manufacturers and applying them to analyze food or feed extracts with different compositions from the previously assessed compositions.
8.3.4 Dispersive Liquid–Liquid Microextraction
To reduce solvent consumption in traditional LLE substantially, DLLME has been used to extract aflatoxins from milk, dairy products, fruit juices, oils, wheat, and eggs. DLLME is a miniaturized extraction technique that offers advantages such as simplicity, rapid operation, high throughput, and low cost. In a usual DLLME protocol, an appropriate mixture of extraction solvent and organic dispersant is rapidly injected into the aqueous sample with a syringe (Rezaee et al. 2006). This generates a cloudy solution consisting of microdroplets of the extraction solvent, which is dispersed entirely into the aqueous phase. After centrifugation, the fine particles of the extraction solvent are settled on the bottom and are removed for further analysis. Thus, the extraction solvent must have higher density and low solubility in water. Because the contact area between the organic solvent and the water sample is large, extraction is fast and efficient. The extent of enrichment of DLLME enhances with dispersion of the extraction solvent. The finer the droplet of the extraction solvent, the higher the enrichment performance. Some parameters affecting the extraction efficiency must be optimized, including the volume of extraction solvent and disperser solvent, extraction, and centrifugation time.
Most analytical methods that use this technique require previous extraction of the sample with a polar solvent given that the basic principle of DLLME is to extract substances from an aqueous or immiscible phase. Table 8.2 contains some examples showing that previous extraction with an aqueous solvent is always performed before DLLME.
8.3.5 QuEChERS
Although the previously described extraction procedures selectively isolate aflatoxins from a complex matrix and use much less solvent than LLE, modern analytical chemistry is continuously developing rapid, easy-to-perform, and low-cost analytical procedures (Perestrelo et al. 2019). QuEChERS is a simple dispersive solid-phase extraction (d-SPE) procedure that can be applied to numerous samples. QuEChERS consists of extracting the homogenized sample with an appropriate solvent, normally acetonitrile, by vortex-shaking for a few minutes. A liquid-liquid partition is created by adding excess salts or buffers to the mixture. After centrifugation, water might be removed with anhydrous MgSO4, and the extract is further cleaned in an additional step in which the extract is mixed with a sorbent, such as primary-secondary amine (PSA), silica gel, C18, or graphitized carbon black (Juan et al. 2017). QuEChERS was initially developed to simplify screening of pesticide residues in large numbers of agricultural samples, but now it has been applied for analysis of many other food contaminants, and aflatoxins are surely among them (Anastassiades et al. 2003; Michlig et al. 2016; Choochuay et al. 2018).
With a classic procedure QuEChERS, AFB1 was extracted from wheat, rice, oat, rye, maize, and barley (Zhao et al. 2017). First, aqueous acetonitrile solution (95:5, v/v) was added to milled samples; then, the mixture was vortexed for 1 min and subjected to ultrasound for 3 min before NaCl and MgSO4 were added. The extract was vortexed for 1 min and centrifuged for 5 min. Next, the supernatant was transferred to another tube containing PSA. After vortexing and centrifugation, the extract was ready for analysis.
Likewise, all other extraction procedures, solvent type, extraction time, and need for adsorbents or not must be optimized before the extraction procedure is effectively established. Also, analysts must always bear in mind that the extraction procedure is unquestionably committed to the detection system that will be used subsequently.
Lastly, even though research has focused on reducing extraction steps, most methods for analysis of aflatoxins still combine two or three approaches to achieve the best results.
8.4 Detection and Quantification of Aflatoxins
8.4.1 Thin-Layer Chromatography
TLC with fluorescence detection was the only chromatographic technique available in the 1960s. Although it was the method of choice of AOAC International (Association of Official Analytical Collaboration International) for an extended period, it is no longer widely used (Trucksess 2000). Despite being a low-cost procedure, the separation efficiency of TLC is low, and identification of aflatoxins might be susceptible to interferences from the fluorescence of other components with similar migration patterns in the sample. Eventually, when combined with a selective cleanup method, such as IACs, TLC is a robust and straightforward screening method (Stroka et al. 2000). Aflatoxins can be quantified if TLC is coupled to densitometry, becoming an alternative for labs that cannot afford more expensive chromatographic methods (Stroka and Anklam 2000; Marutoiu et al. 2004). In two-dimensional thin-layer chromatography (2D-TLC), the plate is rotated 180° after the first separation, and aflatoxins and other components of the sample are eluted once more with a second solvent (Durakovic et al. 2012). High-performance thin-layer chromatography (HPTLC) and bidirectional HPTLC are derived from the previous TCL and have been successfully applied for quantification of aflatoxins in food and feed (Tomlins et al. 1989; Ramesh et al. 2013).
8.4.2 High-Performance Liquid Chromatography Coupled to Fluorescence Detector
The most widely used strategy to determine aflatoxins in food and feed is separation by HPLC followed by fluorescence detection. However, although AFB1 and AFG1 exhibit natural fluorescence, it is less intense than the fluorescence of AFB2 and AFG2. Moreover, water, acetonitrile, and methanol, used as mobile phases in reversed-phase liquid chromatography, also quench the fluorescence of AFB1 and AFG1. Pre- or post-column derivatization methods are recurrently used to circumvent this issue, to increase the signal during analysis. Pre-column derivatization with trifluoroacetic acid (TFA) hydrolyzes AFB1 and AFG2, to form the more fluorescent hemiacetals AFB2a and AFG2a. Even though the time required for complete reaction is short, derivatization represents an additional step. Nevertheless, it is worth performing because derivatization enhances detection (Saito et al. 2020; Wang et al. 2020). Detection limits ranging from 0.1–0.2 μg kg−1 or tenfold lower are easily achieved and entirely meet the requirements of analytical methods for surveillance. Post-column derivatization is accomplished by adding pyridinium bromide-perbromide (PBPB) to the mobile phase after separation. Two atoms of the bromide are added at the 8,9-double bond of the dihydrofuran moiety of aflatoxin, enhancing the fluorescence signal (Stroka et al. 2001). Such bromination is more cost-effective, but bromine can also be produced by an electrochemical cell (Kobra™ Cell) in the post-column step by adding KBr to the mobile phase (Kok 1994; Omotayo et al. 2019). Extraction by IAC and quantification by reversed-phase high-performance liquid chromatography-fluorescence detector (HPLC-FD) without or with pre- or post-column derivatization are among the official methods adopted by AOAC International (AOAC International 2002). Although the mass spectrometry detector has continuously replaced the fluorescence detector, the latter is still widely employed for various purposes because it is spread among analytical chemistry laboratories, as shown in Table 8.3.
8.4.3 Liquid Chromatography Coupled to Mass Spectrometry Detector
Since the mid-1990s, when atmospheric pressure ionization (API) interfaces were developed and overcame the low sensitivity and ionization efficiency of thermospray, particle beam, and fast atom bombardment interfaces, liquid chromatography-mass spectrometry has emerged as the most powerful technique for identification and quantification of contaminants in food (Miklós et al. 2020).
Commercially available atmospheric pressure ion sources include ESI (electrospray), APCI (atmospheric pressure chemical ionization), and APPI (atmospheric pressure photoionization). Any of them can analyze aflatoxins; however, the ESI source is undoubtedly the most frequently found in laboratories and the most employed (Capriotti et al. 2010). After exiting the API source, the molecules enter the vacuum chamber and reach the mass analyzer through an ion transporting and focusing region. Single-stage or multistage (MS/MS) mass analyzers are commercially available. Except for in-source CID, there is no collision-induced dissociation (CID) in a single-stage mass analyzer, and molecular ions cannot be fragmented. Thus single-stage mass analyzers do not meet the European Union recommendations for analysis of residues in food because a precursor ion and two product ions are required to confirm a contaminant (European Commission 2002). This can be achieved by multiple reaction monitoring (MRM) of selected ions, a parameter that is experimentally optimized for each compound.
Aflatoxins can be analyzed on a MS/MS mass analyzer like triple quadrupole (QqQ), quadrupole time-of-flight (Q-TOF), quadrupole-linear ion trap (Q-TRAP), and Orbitrap. Although triple-quadrupole is the most regularly used for determining mycotoxins, not all analytical standards are commercially available. As a result, interest in high-resolution mass spectrometry (HRMS), such as Orbitrap and time-of-flight (TOF) mass analyzers, has increased. HRMS has essential advantages: it records full scan spectra by measuring the accurate mass of analytes, screens untargeted compounds, and reviews analysis data, allowing analytes that had not been considered at the time of spectral acquisition to be investigated (Tittlemier et al. 2021).
One of the main advantages of LC-MS/MS systems is their remarkable sensitivity and selectivity, dismissing the need for extensive cleanup of sample extracts. Nevertheless, for some substances in very complex samples, cleanup cannot be entirely neglected when high sensitivity is desired. When it comes to the practical use of LC-MS/MS methods, co-eluting matrix components might significantly suppress or enhance the signals of the analytes. In other words, analyte ionization is prevented by competition of charges from the other components of the sample. This is the well-recognized “matrix effect” in mass spectrometry detection, and it harms the performance of LC-MS/MS methods, mainly in terms of the accuracy of quantification (Truffeli et al. 2011a, b). For instance, if a solvent calibration curve is prepared with the analytical standards for the quantification, differences in the signals of the analytical standards and sample extracts will directly impact the result. There is no universal approach, but understanding why signals are suppressed or enhanced might support the analyst’s decision.
The most straightforward approach to avoid the matrix effect is to dilute the sample extract in an appropriate solvent (Stahnke et al. 2012). However, diluting the extract will also dilute aflatoxin, and the mass spectrometer might not be sensitive enough to overcome the loss in concentration. If calibration curves are prepared in blank extracts, a similar suppression or enhancement effect is predicted both for standards and sample extracts. This approach is named the matrix-matched calibration curve. Nevertheless, the availability of samples free from the contaminant should be verified before deciding on this method. The standard addition method is laborious and time-consuming, especially when more than one aflatoxin must be quantified. Another valuable approach is the stable isotope (SI) dilution assay. Deuterated and 13C-aflatoxins are commercially available and considered the ideal Internal Standards. SI solutions can be added to sample extracts and calibration curves or incorporated in the sample before extraction and cleanup (Varga et al. 2012). This procedure provides enormous flexibility under the conditions of sample extraction and significantly improves the precision of the method, but SIs are expensive, which should be borne in mind before choosing the methodology.
Due to its outstanding performance, it is not surprising that LC-MS/MS has been widely and successfully employed to determine aflatoxins in food and feed. Table 8.4 depicts several applications of LC-MS/MS in diverse samples together with the extraction and cleanup procedures.
8.4.4 Screening and Rapid Methods
Enzyme-linked immunosorbent assay (ELISA) is the most common and extensively used screening method for determination of aflatoxins in agricultural raw materials. ELISA is easy to perform, is not as expensive as chromatography, does not use organic solvents, and is essential to provide on-site results about aflatoxins in a short period. Therefore, it is a standard and well-accepted method for monitoring aflatoxins. ELISA kits are commercially available and also provide quantitative results. Several samples can be analyzed without any extensive cleaning step. However, ELISA is highly matrix-dependent, so analysis of more complex samples requires that the manufacturer be consulted or the method be individually validated for the specific sample (Miklós et al. 2020).
To quantify AFM1 in raw milk, Maggira et al. (2021) validated a commercial ELISA kit among three commercially available kits against an HPLC-FL method. The authors found that the ELISA kit was a faster and equally reliable alternative method to HPLC in routine analysis.
A calibration curve implanted enzyme-linked immunosorbent assay (C-ELISA) was developed to determine aflatoxin B1 in wheat, corn, soybean, and peanuts (Wu et al. 2020). The new development implanted an optimized standard curve data into a matched analysis software, programmed by the researchers, to make data processing more convenient and faster. The new method proved rapid and sensitive and provided equivalent results to HPLC for all the AFB1 concentrations in real samples.
AFB1 detection by electrochemical immunoassays is sensitive and fast. Kong et al. (2018) used 2-aminoethanethiol to increase the speed and sensitivity of a conventional electrochemical immunoassay by assembling the thiol on the surface of a gold electrode, to form self-assembled monolayers. Then, non-competitive immunoassays occurred on the surface, to give an electrochemical immunoassay sensor. The detection limit achieved by the new development was 0.1 ng mL−1 AFB1.
Among new developments, Fan et al. (2020) established a time-resolved fluorescence immunoassay based on fluorescent microspheres containing a Eu3+ chelate named AFM1-POCT. They used a portable fluorimeter, and the reaction took 5 min. The results were equivalent to the results of UHPLC-MS determination in the range of 0.0121–2.0 μg kg−1, so the method met the detection limits of 0.05–0.5 μg kg−1 required by the regulatory organization and enables on-site sampling.
8.5 Analytical Method Validation
Analytical method validation essentially involves evaluating whether a new or a modified literature method applies to the routine of a certain laboratory. The main objective is to demonstrate that the analytical method is appropriate, ensuring that it is accurate, reproducible, and applicable to the substance intended for identification and quantification. The method is considered validated when it is evaluated according to a series of at least some preestablished parameters. The evaluated performance parameters will vary depending on the intended use of the method, its type (quantitative or qualitative), and the degree to which it has been previously validated (FDA 2019). For example, new quantitative methods should include at least the following performance characteristics: selectivity, detection limit, quantification limit, linearity, or other calibration models, range, accuracy, precision, measurement uncertainty, ruggedness, confirmation of identity, and spike recovery (FDA 2019).
Vast literature is available to assist the validation process for those who intend to proceed with an in-house validation. The most comprehensive and maybe widely accepted guidance is the European Commission Council Directive concerning the performance of analytical methods and the interpretation of results (European Commission 2002). National guidelines might also be compulsory and might be accessed by region or country, if necessary. Raposo and Ibell-Bianco (2020) presented a valuable discussion about general analytical method validation, which was extremely useful because the authors presented discrepancies and controversies among different guidelines for obtaining and interpreting the most required parameters in analytical method validation.
Considering how aflatoxins are formed in food and feed, validation should be best evaluated with Certified Reference Materials (CRM), if available. Matrix reference materials with naturally occurring mycotoxins are preferred over fortified ones because the incurred mycotoxins are incorporated deeper within the matrix (Tittlemier et al. 2021). Using a spiked matrix with standard solutions to determine recovery might yield unrealistic values (Dzuman et al. 2014). Finally, proficiency tests or interlaboratory studies are crucial. Numerous collaborative studies have been carried out by AOAC International (Bao et al. 2012; Stroka et al. 2001).
Thus, assuming the importance of this topic associated with strong regulations of some segments, laboratories must attend to their analytical methods and their adequate validation whenever appropriate.
8.6 Multiclass-Mycotoxin Methods of Analysis
Unfortunately, aflatoxin-producing fungi are not the only fungi that infest crops, and even fungi related to the synthesis aflatoxins might produce other mycotoxins. Besides aflatoxins, the most investigated mycotoxins in food and feed are Fumonisin B1 (FB1), Fumonisin B2 (FB2), Ochratoxin (OTA), Deoxynivalenol (DON), Nivalenol (NIV), Zearalenone, (ZEA), T-2, and HT-2, among others.
Current mycotoxin regulations and acceptable levels in food and feed apply to many different individual mycotoxins in a single food, which emphasizes the importance of establishing methods that can simultaneously determine multiple mycotoxins in a single analysis (European Commission 2006a). To achieve these goals, methods for determining a group of mycotoxins became common (Lago et al. 2021). Due to the various structures and physical and chemical properties of different mycotoxins, extraction and analysis parameters must be adapted to the intended matrixes, to meet the minimum requirements of recovery, sensitivity, and selectivity. Routine determination of multiple mycotoxins is only possible, thanks to significant advances in extraction and purification techniques and notable increase in the sensitivity of triple quadruple mass spectrometers frequently coupled to liquid chromatography, as already mentioned. Diverse multi-mycotoxin analytical methods are described in the specialized literature (González-Jartín et al. 2021)
8.7 Multi-Residue Methods of Analysis
Besides the multiple mycotoxins that are likely to contaminate food and feed, other harmful substances exist. Other toxic substances such as pesticides, veterinary drugs, hormones, and plant alkaloids might also be incorporated along the food production chain. Multi-residue methods for several analytes differing in polarity, structural formulas, and physicochemical properties are becoming regularly accessible (Steiner et al. 2021a, b). Because the surveillance of aflatoxins in food and feed is mandatory and well-recognized, these contaminants are recurrently included in the list of multiclass methods. When a method for multi-residue determination is employed, almost all efforts are directed to increasing the number of identified or quantified analytes and reducing the time required for analysis. Analyzing more analytes in a shorter time means saving resources and making faster decisions, especially decisions related to accepting a raw material batch or not or releasing a final product to consumers.
With single methods, aflatoxins can be quantitatively extracted after proper cleanup and determined with a suitable detector. In contrast, a compromise among all the components is needed when developing multiclass methods, especially for complex samples, in which the applicability of analyte-specific extraction is not practicable (Steiner et al. 2020). Multi-residue analytical methods also expand the possibility of screening before a more specific method is applied. The numerous investigations and efforts in this research area brought impressive advances in approaches for sample preparation, identification, and quantitation (Dzuman et al. 2015). Diverse applications are easily found in the specialized literature (Steiner et al. 2021a, b).
8.8 Conclusions
Since aflatoxins were discovered, they have attracted a lot of attention, effort, and resources. The search for new analytical methods to determine mycotoxins is undoubtedly a fertile field of research. Protocols for sample preparation have been continuously improved and optimized for analysis of aflatoxins in various food and feed matrixes, having progressed from laborious liquid-liquid extractions to solid-phase extraction and modern immunoaffinity columns, culminating in the simple dilute and shoot and QuEChER approaches. Faster cleanup has allowed significant advances in high throughput analysis. Different analytical protocols for determining aflatoxins in food commodities have advanced and gradually improved. Despite drawbacks such as low sensitivity and poor accuracy, TLC was the most used chromatographic technique for quantification of aflatoxins until the 1980s. Thereafter, it was steadily replaced with HPLC coupled to ultraviolet and fluorescence detectors. IAC cleanup with liquid chromatography separation and fluorescence detection is widely used as a gold analytical method in laboratories worldwide because it has been extensively validated in collaborative studies and recognized by regulatory boards. Mass spectrometry detectors impressively enhanced the selectivity and sensitivity of methods for the determination of aflatoxins and multiple mycotoxins. Liquid chromatography coupled to mass spectrometry is the most potent tool for monitoring and controlling the levels of aflatoxins in food and feed. Due to its vast applicability, LC-MS/MS instruments have become the mainstream device in almost all research and routine laboratories. However, its inclusion in several laboratories is hampered by the high costs for acquiring, maintaining, and training personnel for the instrument. Finally, screening and fast methods, represented mainly by ELISA, are essential for on-site monitoring of aflatoxins. Constant developments to improve immunoassays and biosensors promise to bring new cost-effective, reliable, and straightforward methods to determine aflatoxins.
References
Afzali D, Ghanbarian M, Mostafavi A, Shamspur T, Ghaseminezhad S (2012) A novel method for high preconcentration of ultra trace amounts of B1, B2, G1 and G2 aflatoxins in edible oils by dispersive liquid–liquid microextraction after immunoaffinity column clean-up. J Chromatogr A 1247:35–41
AlFaris NA, Wabaidur SM, Alothman ZA, Altamimi JZ, Aldayel TS (2020) Fast and efficient immunoaffinity column cleanup and liquid chromatography–tandem mass spectrometry method for the quantitative analysis of aflatoxins in baby food and feeds. J Sep Sci 43:2079–2087
Al-Ghouti MA, AlHusaini A, Abu-Dieyeh MH, Abd Elkhabeer M, Alam MM (2020) Determination of aflatoxins in coffee by means of ultra-high performance liquid chromatography-fluorescence detector and fungi isolation. Int J Environ Anal Chem:1–16
Amirkhizi B, Nemati M, Arefhosseini SR, Shahraki SH (2018) Application of the ultrasonic-assisted extraction and dispersive liquid–liquid microextraction for the analysis of AFB1 in egg. Food Anal Methods 11:913–920
Anastassiades M, Lehotay SJ, Stajnbaher D, Schenck FJ (2003) Fast and easy multiresidue method employing acetonitrile extraction/partitioning and “dispersive solid-phase extraction” for the determination of pesticide residues in produce. J AOAC Int 86:412–431
Anttila A, Bhat RV, Bond JA, Borghoff SJ, Bosch FX, Carlso GP, Perez E (2002) IARC monographs on the evaluation of carcinogenic risks to humans: some traditional herbal medicines, some mycotoxins, naphthalene and styrene. IARC Monogr Eval Carcinog Risks Hum 82:1–556
Anukul N, Vangnai K, Mahakarnchanakul W (2013) Significance of regulation limits in mycotoxin contamination in Asia and risk management programs at the national level. J Food Drug Anal 21:227–241
ANVISA (2011) Agência Nacional de Vigilância Sanitária. Resolução RDC n 7, de 18 de fevereiro de 2011. Diário Oficial da União e Seção 1, n 37, 22 de fevereiro de 2011. http://bvsms.saude.gov.br/bvs/saudelegis/anvisa/2011/res0007_18_02_2011_rep.html. Accessed 15 January 2021
AOAC International (2002) Method 991.31-1994. Aflatoxins in corn, raw peanuts, and peanut butter immunoaffinity column (AflaTest) method. Gaithersburg, MD
Asao T, Buchi G, Abdel-Kader MM, Chang SB, Wick EL, Wogan GN (1963) Aflatoxins B and G. J Am Chem Soc 85:1706–1707
Ayelign A, De Saeger S (2020) Mycotoxins in Ethiopia: current status, implications to food safety and mitigation strategies. Food Control 113:1–9
Bakirci GT (2020) Investigation of aflatoxins levels in commercial dried figs from western Turkey. Int Food Res J 27:245–251
Bao L, Liang CZ, Trucksess MW, Xu YL, Lv N, Wu ZX (2012) Determination of Aflatoxins B-1, B-2, G(1), and G(2) in olive oil, peanut oil, and sesame oil using immunoaffinity column cleanup, post-column derivatization, and liquid chromatography/fluorescence detection: collaborative study. J AOAC Int 95:1689–1700
Berthiller F, Brera C, Iha MH, Krska R, Lattanzio VMT, MacDonald S, Malone RJ, Maragos C, Solfrizzo M, Stranska-Zachariasovas M, Stroka J, Tittlemier SA (2017) Developments in mycotoxin analysis: an update for 2015–2016. World Mycotoxin J 10:5–29
Budavari S, O'Neil MJ, Smith A, Heckelman PE, Kinneary JF (2001) The Merk index. An encyclopedia of chemicals, drugs and biologicals. 13 Ed. Merck and Co. Inc., Whitehouse Station, NJ, 1097, 1946
Campone L, Piccinelli AL, Celano R, Pagano I, Russo M, Rastrelli L (2016) Rapid and automated analysis of aflatoxin M1 in milk and dairy products by online solid phase extraction coupled to ultra-high-pressure-liquid-chromatography tandem mass spectrometry. J Chromatogr A 1428:212–219
Capriotti AL, Foglia P, Gubbiotti R, Roccia C, Samperi R, Laganà A (2010) Development and validation of a liquid chromatography/atmospheric pressure photoionization-tandem mass spectrometric method for the analysis of mycotoxins subjected to commission regulation (EC) No. 1881/2006 In cereals. J Chromatogr A 1217:6044–6051
Castegnaro M, Tozlovanu M, Wild C, Molinié A, Sylla A, Pfohl-Leszkowicz A (2006) Advantages and drawbacks of immunoaffinity columns in analysis of mycotoxins in food. Mol Nutr Food Res 50:480–487
Chen F, Luan C, Wang L, Wang S, Shao L (2017) Simultaneous determination of six mycotoxins in peanut by high-performance liquid chromatography with a fluorescence detector. J Sci Food Agric 97:1805–1810
Choochuay S, Phakam J, Jala P, Maneeboon T, Tansakul N (2018) Determination of aflatoxin B1 in feedstuffs without clean-up step by high-performance liquid chromatography. Int J Anal Chem 2018:1–9
Dhanasekaran D, Shanmugapriya S, Thajuddin N, Panneerselvam A (2011) Aflatoxins and aflatoxicosis in human and animals. Aflatoxins-Biochem Mol Biol:221–254
Du L, Wang S, Huang J, Chu C, Li R, Li Q, Yang J (2018) Determination of aflatoxin M1 and B1 in milk and jujube by miniaturized solid-phase extraction coupled with ultra high performance liquid chromatography and quadrupole time-of-flight tandem mass spectrometry. J Sep Sci 41:3677–3685
Durakovic L, Delas F, Tudic A, Huic-Babic K, Redzepovic S (2012) Removal of aflatoxin M1 from artificially contaminated yoghurt by using of new synthesized dehydroacetic acid analogues. Mljekarstvo: časopis za unaprjeđenje proizvodnje i prerade mlijeka 62:179–191
Dzuman Z, Zachariasova M, Lacina O, Veprikova Z, Slavikova P, Hajslova J (2014) A rugged high-throughput analytical approach for the determination and quantification of multiple mycotoxins in complex feed matrices. Talanta 121:263–272
Dzuman Z, Zachariasova M, Veprikova Z, Godula M, Hajslova J (2015) Multi-analyte high performance liquid chromatography coupled to high resolution tandem mass spectrometry method for control of pesticide residues, mycotoxins, and pyrrolizidine alkaloids. Anal Chim Acta 863:29–40
Ertekin O, Kaymak PSS, Akçael E, Oztürk S (2019) Aflatoxin-specific monoclonal antibody selection for immunoaffinity column development. BioTechniques 66:261–268
Espinosa-Calderón A, Contreras-Medina LM, Muñoz-Huerta RF, Millán-Almaraz JR, González RGG, Torres-Pacheco I (2011) Methods for detection and quantification of aflatoxins. Aflatoxins: detection, measurement and control. InTech, New York, pp 109–128
European Commission (2002) Commission Decision 2002/657/EC of 12 August 2002 implementing Council Directive 96/23/EC concerning the performance of analytical methods and the interpretation of results, as amended by Decision 2003/181/EC. Off J Eur Commun 221:8–36
European Commission (2003) Commission Directive 2003/100/EC of 31 October 2003 amending Annex I to Directive 2002/32/EC of the European Parliament and of the Council on undesirable substances in animal feed. Off J Eur Union L 285:33–37
European Commission (2006a) Commission Regulation (EC) No 1881/2006 of 19 December 2006 setting maximum levels for certain contaminants in foodstuffs. Off J Eur Union 364:5–24
European Commission (2006b) Commission Regulation (EC) No 401/2006 of 23 February 2006 laying down the methods of sampling and analysis for the official control of the levels of mycotoxins in foodstuffs. Off J Eur Union 70:12–34
Fan S, Li Q, Zhang X, Cui X, Zhang D, Zhang Y (2015) Simultaneous determination of aflatoxin B1, B2, G1, and G2 in corn powder, edible oil, peanut butter, and soy sauce by liquid chromatography with tandem mass spectrometry utilizing turbulent flow chromatography. J Sep Sci 38:1310–1317
Fan J, Yuan X, Li W, Zhou Y, Zhang J, Zhang Y, Zhou B (2020) Rapid and ultrasensitive method for determination of aflatoxin M1 in milk. Food Agric Immunol 31:849–858
FDA, Food and Drug Administration (2019) Guidelines for the validation of chemical methods in food, feed, cosmetics, and veterinary products. Food and Drug Administration, Silver Spring, MD, pp 1–39. https://www.fda.gov/media/81810/download. Accessed 08 February 2021
Fifield FW, Kealey D (2000) Principles and practice of analytical chemistry. Blackwell Science, Hoboken
Galaverna G, Dall'Asta C (2012) Sampling techniques for the determination of Mycotoxins in food matrices. In: Pawliszyn J (ed) Comprehensive sampling and sample preparation. Academic Press, Oxford, pp 381–403
García-Moraleja A, Font G, Mañes J, Ferrer E (2015) Development of a new method for the simultaneous determination of 21 mycotoxins in coffee beverages by liquid chromatography tandem mass spectrometry. Food Res Int 72:247–255
González-Jartín JM, Rodríguez-Cañás I, Alfonso A, Sainz MJ, Vieytes MR, Gomes A, Botana LM (2021) Multianalyte method for the determination of regulated, emerging and modified mycotoxins in milk: QuEChERS extraction followed by UHPLC–MS/MS analysis. Food Chem 356:129647
Hamed AM, Moreno-González D, García-Campaña AM, Gámiz-Gracia L (2017) Determination of aflatoxins in yogurt by dispersive liquid–liquid microextraction and HPLC with photo-induced fluorescence detection. Food Anal Methods 10:516–521
Hamed AM, Abdel-Hamid M, Gámiz-Gracia L, García-Campaña AM, Arroyo-Manzanares N (2019) Determination of aflatoxins in plant-based milk and dairy products by dispersive liquid–liquid microextraction and high-performance liquid chromatography with fluorescence detection. Anal Lett 52:363–372
Iha MH, Mini CA, Okada IA, de Cássia BR, Trucksess MW (2017) The use of regenerated immunoaffinity columns for aflatoxins B1, B2, G1 and G2 in peanut confection. J. Chromatogr A 1483:1–7
Jayasinghe GTM, Domínguez-González R, Bermejo-Barrera P, Moreda-Piñeiro A (2020) Combining ultrasound-assisted extraction and vortex-assisted liquid–liquid microextraction for the sensitive assessment of aflatoxins in aquaculture fish species. J Sep Sci 43:1331–1338
Jimenez Medina ML, Lafarga T, Garrido Frenich A, Romero-González R (2021) Natural occurrence, legislation, and determination of aflatoxins using chromatographic methods in food: a review (from 2010 to 2019). Food Rev Int 37:244–275
Juan C, Mañes J, Font G, Juan-García A (2017) Determination of mycotoxins in fruit berry by-products using QuEChERS extraction method. Lwt 86:344–351
Kaale LD, Kimanya ME, Macha IJ, Mlalila N (2021) Aflatoxin contamination and recommendations to improve its control: a review. World Mycotoxin J 14:27–40
Kamel E, Bazalou M, Sdeek FA, Konuk M (2017) Comparison of liquid chromatography instruments with single quadrupole and tandem mass spectrometry for trace level analysis: Aflatoxin M1 in white cheese. Int J Food Prop 20:2294–2304
Kamimura H, Nishijima M, Yasuda K, Ushiyama H, Tabata S, Matsumoto S, Nishima T (1985) Simple, rapid clean-up method for analysis of aflatoxins and comparison with various methods. J Assoc Off Anal Chem 68:458–461
Kara GN, Ozbey F, Kabak B (2015) Co-occurrence of aflatoxins and ochratoxin A in cereal flours commercialised in Turkey. Food Control 54:275–281
Karaseva NM, Amelin VG, Tret’Yakov AV (2014) QuEChERS coupled to dispersive liquid-liquid microextraction for the determination of aflatoxins B1 and M1 in dairy foods by HPLC. J Anal Chem 69:461–466
Kok WT (1994) Derivatization reactions for the determination of aflatoxins by liquid chromatography with fluorescence detection. J Chromatogr B Biomed Appl 659:127–137
Kokkonen M, Jestoi M, Rizzo A (2005) Determination of selected mycotoxins in mould cheeses with liquid chromatography coupled to tandem with mass spectrometry. Food Add Contam 22:449–456
Kong Z, Wang H, Zou L, Ji Z (2018) Enhancement of aflatoxin B1 detection using electrochemical immunoassay method and 2-aminoethanethiol. Mater Res Express 5:066414
Lago LO, Nievierowski TH, Mallmann LP, Rodrigues E, Welke JE (2021) QuEChERS-LC-QTOFMS for the simultaneous determination of legislated and emerging mycotoxins in malted barley and beer using matrix-matched calibration as a solution to the commercial unavailability of internal standards for some mycotoxins. Food Chem 345:128744
Lancaster MC, Jenkins FP, Philp JM (1961) Toxicity associated with certain samples of groundnuts. Nature 192:1095–1096
Le Breton E, Frayssinet C, Boy J (1962) Sur l'apparition d'hepatomes" spontanes" chez le rat wistar. Role de la toxine de l'Aspergillus flavus. Interet en pathologie humaine et cancerologie experimentale. R Acad Sci 25:784–786
Lee D, Lee KG (2015) Analysis of aflatoxin M1 and M2 in commercial dairy products using high-performance liquid chromatography with a fluorescence detector. Food Control 50:467–471
Li X, Zhao L, Fan Y, Jia Y, Sun L, Ma S, Zhang J (2014) Occurrence of mycotoxins in feed ingredients and complete feeds obtained from the Beijing region of China. J Anim Sci Biotechnol 5:1–8
Liao CD, Wong JW, Zhang K, Hayward DG, Lee NS, Trucksess MW (2013) Multi-mycotoxin analysis of finished grain and nut products using high-performance liquid chromatography–triple-quadrupole mass spectrometry. J Agric Food Chem 61:4771–4782
Liao X, Jia B, Sun C, Shi L, Liu X, Zhou L, Kong W (2020) Reuse of regenerated immunoaffinity column for excellent clean-up and low-cost detection of trace aflatoxins in malt. Microchem J 157:105007
Liu L, Jin H, Sun L, Ma S, Lin R (2012) Determination of aflatoxins in medicinal herbs by high-performance liquid chromatography–tandem mass spectrometry. Phytochem Anal 23:469–476
Maggira M, Ioannidou M, Sakaridis I, Samouris G (2021) Determination of Aflatoxin M1 in raw milk using an HPLC-FL method in comparison with commercial ELISA Kits—application in raw milk samples from various regions of greece. Vet Sci 8:46
Maia PP, Siqueira MEPB (2002) Occurrence of aflatoxins B 1, B 2, G 1 and G 2 in some Brazilian pet foods. Food Addit Contam 19:1180–1183
Mannani N, Tabarani A, El Adlouni C, Zinedine A (2021) Aflatoxin M1 in pasteurized and UHT milk marked in Morocco. Food Control 124:107893
Marchese S, Polo A, Ariano A, Velotto S, Costantini S, Severino L (2018) Aflatoxin B1 and M1. Biological properties and their involvement in cancer development. Toxins 10:214
Marutoiu C, Puiu S, Moise MI, Soran L, Maruţoiu OF, Bobos L (2004) Optimization of the separation of some aflatoxins by thin-layer chromatography. JPC-J Planar Chromat 17:372–374
Michlig N, Repetti MR, Chiericatti C, García SR, Gaggiotti M, Basílico JC, Beldoménico HR (2016) Multiclass compatible sample preparation for UHPLC–MS/MS determination of aflatoxin M1 in raw milk. Chromatographia 79:1091–1100
Miklós G, Angeli C, Ambrus Á, Nagy A, Kardos V, Zentai A, Kerekes K, Farkas Z, Ákos Józwiak Á, Bartók T (2020) Detection of aflatoxins in different matrices and food-chain positions. Front Microbiol 11:1916
Ok HE, Tian F, Hon EY, Paek O, Kim SH, Kim D, Chun HS (2016) Harmonized collaborative validation of aflatoxins and sterigmatocystin in white rice and sorghum by liquid chromatography coupled to tandem mass spectrometry. Toxins 8:371
Olsen M, Johnsson P, Möller T, Paladino R, Lindblad M (2008) Aspergillus nomius, an important aflatoxin producer in Brazil nuts? World Mycotoxin J 1:123–126
Omotayo OP, Omotayo AO, Babalola OO, Mwanza M (2019) Comparative study of aflatoxin contamination of winter and summer ginger from the North West Province of South Africa. Toxicol Rep 6:489–495
Otles S, Kartal C (2016) Solid-Phase Extraction (SPE): principles and applications in food samples. Acta Sci Pol Technol Aliment 15:5–15
Otta KH, Papp E, Bagocsi B (2000) Determination of aflatoxins in food by overpressured-layer chromatography. J Chromatogr A 882:11–16
Ouakhssase A, Chahid A, Choubbane H, Aitmazirt A, Addi EA (2019) Optimization and validation of a liquid chromatography/tandem mass spectrometry (LC-MS/MS) method for the determination of aflatoxins in maize. Heliyon 5:01565
Park JW, Kim YB (2006) Effect of pressure cooking on aflatoxin B1 in rice. J Agric Food Chem 54:2431–2435
Parker WA, Melnick D (1966) Absence of aflatoxin from refined vegetable oils. J Am Oil Chem Soc 43:635–638
Patey AL, Sharman M, Gilbert J (1991) Liquid chromatographic determination of aflatoxin levels in peanut butters using an immunoaffinity column cleanup method: International collaborative trial. J Assoc Off Anal Chem 74:76–81
Patyal A, Gill JPS, Bedi JS, Aulakh RS (2021) Assessment of aflatoxin contamination in dairy animal concentrate feed from Punjab, India. Environ Sci Pollut Res Int:1–11
Perestrelo R, Silva P, Porto-Figueira P, Pereira JA, Silva C, Medina S, Câmara JS (2019) QuEChERS-Fundamentals, relevant improvements, applications and future trends. Anal Chim Acta 1070:1–28
Pons WA, Goldblatt LA (1965) The determination of aflatoxins in cottonseed products. J Am Oil Chem Soc 42:471–475
Ramesh J, Ghadevaru S, Sureshkumar V (2013) Analysis of feed samples for aflatoxin B1 contamination by HPTLC-a validated method. Int J Curr Microbiol Appl Sci 2:373–377
Raposo F, Ibelli-Bianco C (2020) Performance parameters for analytical method validation: controversies and discrepancies among numerous guidelines. Trends Analyt Chem:115913
Reiter E, Zentek J, Razzazi E (2009) Review on sample preparation strategies and methods used for the analysis of aflatoxins in food and feed. Mol Nutr Food Res 53:508–524
Rezaee M, Assadi Y, Hosseini MRM, Aghaee E, Ahmadi F, Berijani S (2006) Determination of organic compounds in water using dispersive liquid–liquid microextraction. J Chromatogr A 1116:1–9
Richard JL (2008) Discovery of aflatoxins and significant historical features. Toxin Rev 27:171–201
Romero-González R, Martinez-Vidal JL, Aguilera-Luiz MM, Garrido Frenich A (2009) Application of conventional solid-phase extraction for multimycotoxin analysis in beers by ultrahigh-performance liquid chromatography− tandem mass spectrometry. J Agric Food Chem 57:9385–9392
Rushing BR, Selim MI (2019) Aflatoxin B1: a review on metabolism, toxicity, occurrence in food, occupational exposure, and detoxification methods. Food Chem Toxicol 124:81–100
Sailaja O, Krishnaveni G, Manoranjani M (2018) Identification and high-performance liquid chromatography quantification of aflatoxins in red chili (Capsicum annuum L.) in Guntur, Andhra Pradesh, India. Asian J Pharm 11:S933–S937
Saito K, Ishii J, Naniwa M, Ishii R, Kato M, Kondo HS, Masaru T, Shigeki H, Takako H, Ito R (2020) Residual analysis of aflatoxins in spice by HPLC coupled with solid-phase dispersive extraction and solid-phase fluorescence derivatization method. J AOAC Int 103:521–1527
Sakin F, Tekeli İO, Yipel M, Kürekci C (2018) Occurrence and health risk assessment of aflatoxins and ochratoxin A in Sürk, a Turkish dairy food, as studied by HPLC. Food Control 90:317–323
Sargeant K, Sheridan A, O'kelly J, Carnaghan RBA (1961) Toxicity associated with certain samples of groundnuts. Nature 192:1096–1097
Scott PM, Trucksess MW (1997) Application of immunoaffinity columns to mycotoxin analysis. J AOAC Int 80:941–950
Sheijooni-Fumani N, Hassan J, Yousefi SR (2011) Determination of aflatoxin B1 in cereals by homogeneous liquid–liquid extraction coupled to high performance liquid chromatography-fluorescence detection. J Sep Sci 34:1333–1337
Sobolev VS (2007) Simple, rapid, and inexpensive clean-up method for quantitation of aflatoxins in important agricultural products by HPLC. J Agric Food Chem 55:2136–2141
Sobolev VS, Dorner JW (2002) Clean-up procedure for determination of aflatoxins in major agricultural commodities by liquid chromatography. J AOAC Int 85:642–645
Spanjer MC, Scholten JM, Kastrup S, Jörissen U, Schatzki TF, Toyofuku N (2006) Sample comminution for mycotoxin analysis: dry milling or slurry mixing? Food Addit Contam 23:73–83
Spanjer MC, Rensen PM, Scholten JM (2008) LC-MS/MS multi-method for mycotoxins after single extraction, with validation data for peanut, pistachio, wheat, maize, cornflakes, raisins and figs. Food Addit Contam 25:472–489
Stahnke H, Kittlaus S, Kempe G, Alder L (2012) Reduction of matrix effects in liquid chromatography–electrospray ionization–mass spectrometry by dilution of the sample extracts: how much dilution is needed? Anal Chem 84:1474–1482
Steiner D, Krska R, Malachová A, Taschl I, Sulyok M (2020) Evaluation of matrix effects and extraction efficiencies of LC–MS/MS methods as the essential part for proper validation of multiclass contaminants in complex feed. J Agric Food Chem 68:3868–3880
Steiner D, Malachov A, Sulyok M, Krska R (2021a) Challenges and future directions in LC-MS-based multiclass method development for the quantification of food contaminants. Anal Bioanal Chem 413:25–34
Steiner D, Malachová A, Sulyok M, Krska R (2021b) Challenges and future directions in LC-MS-based multiclass method development for the quantification of food contaminants. Anal Bioanal Chem 413:25–34
Stroka J, Anklam E (2000) Development of a simplified densitometer for the determination of aflatoxins by thin-layer chromatography. J Chromatogr A 904:263–268
Stroka J, van Otterdijk R, Anklam E (2000) Immunoaffinity column clean-up prior to thin-layer chromatography for the determination of aflatoxins in various food matrices. J Chromatogr A 904:251–256
Stroka J, Anklam E, Joerissen U, Gilbert J (2001) Determination of aflatoxin B1 in baby food (infant formula) by immunoaffinity column cleanup liquid chromatography with postcolumn bromination: collaborative study. J AOAC Int 84:1116–1124
Tittlemier SA, Brunkhorst J, Cramer B, DeRosa MC, Lattanzio VMT, Malone R, Sumarah MW (2021) Developments in mycotoxin analysis: an update for 2019–2020. World Mycotoxin J 14:3–26
Tomlins KI, Jewers K, Coker RD, Nagler MJ (1989) A bi-directional HPTLC development method for the detection of low levels of aflatoxin in maize extracts. Chromatographia 27:49–52
Trucksess MW (2000) Natural toxins. In: Horwitz W (ed) Official methods of analysis, 17th edn. AOAC International, Gaithersburg, MD, pp 1–64
Trufelli H, Palma P, Famiglini G, Cappiello A (2011a) An overview of matrix effects in liquid chromatography–mass spectrometry. Mass Spectr Ver 30:491–509
Trufelli H, Palma P, Famiglini G, Cappiello A (2011b) An overview of matrix effects in liquid chromatography–mass spectrometry. Mass Spectr Rev 30:491–509
Turner NW, Subrahmanyam S, Piletsky SA (2009) Analytical methods for determination of mycotoxins: a review. Anal Chim Acta 632:168–180
Uchigashima M, Saigusa M, Yamashita H, Miyake S, Fujita K, Nakajima M, Nishijima M (2009) Development of a novel immunoaffinity column for aflatoxin analysis using an organic solvent-tolerant monoclonal antibody. J Agr Food Chem 57:8728–8734
Van der Zijden ASM, Koelensmid WAA, Boldixgh J, Barrett CB, Ord WO, Philp J (1962) Isolation in crystalline form of a toxin responsible for Turkey X disease. Nature, London 195:4846
Varga E, Glauner T, Köppen R, Mayer K, Sulyok M, Schuhmacher Rudolf K, Berthiller F (2012) Stable isotope dilution assay for the accurate determination of mycotoxins in maize by UHPLC-MS/MS. Anal Bioanal Chem 402:2675–2686
Ventura M, Gómez A, Anaya I, Díaz J, Broto F, Agut M, Comellas L (2004) Determination of aflatoxins B1, G1, B2 and G2 in medicinal herbs by liquid chromatography–tandem mass spectrometry. J Chromatogr A 1048:25–29
Waltking AE (1970) Collaborative study of three methods for determination of aflatoxin in peanuts and peanut products. J Assoc Off Anal Chem 53:104–113
Wang N, Duan C, Li S, Geng X, Ding K, Guan Y (2020) Aqueous extraction followed by dispersive solid phase extraction with in situ derivatization for the determination of aflatoxins in traditional Chinese medicines. J Chromatogr A 1618:460894
Wang N, Duan C, Geng X, Li S, Ding K, Guan Y (2019) One step rapid dispersive liquid-liquid micro-extraction with in-situ derivatization for determination of aflatoxins in vegetable oils based on high performance liquid chromatography fluorescence detection. Food Chem 287:333–337
Wesolek N, Roudot AC (2016) Assessing aflatoxin B1 distribution and variability in pistachios: validation of a Monte Carlo modeling method and comparison to the Codex method. Food Control 59:553–560
Williams JH, Phillips TD, Jolly PE, Stiles JK, Jolly CM, Aggarwal D (2004) Human aflatoxicosis in developing countries: a review of toxicology, exposure, potential health consequences, and interventions. Am J Clin Nutr 80:1106–1122
Wogan GN (1966) Chemical nature and biological effects of the aflatoxins. Bacteriol Rev 30:460
Womack ED, Sparks DL, Brown AE (2016) Aflatoxin M1 in milk and milk products: a short review. World Mycotoxin J 9:305–315
Wu Y, Yu J, Li F, Li J, Shen Z (2020) A calibration curve implanted enzyme-linked immunosorbent assay for simultaneously quantitative determination of multiplex mycotoxins in cereal samples, soybean and peanut. Toxins 12:718
Ye Z, Cui P, Wang Y, Yan H, Wang X, Han S, Zhou Y (2019) Simultaneous determination of four aflatoxins in dark tea by multifunctional purification column and immunoaffinity column coupled to liquid chromatography tandem mass spectrometry. J Agric Food Chem 67:11481–11488
Zareshahrabadi Z, Bahmyari R, Nouraei H, Khodadadi H, Mehryar P, Asadian F, Zomorodian K (2020) Detection of aflatoxin and Ochratoxin A in spices by high-performance liquid chromatography. J Food Qual 2020:1–8
Zhang K, Banerjee K (2020) A review: sample preparation and chromatographic technologies for detection of aflatoxins in foods. Toxins 12:539
Zhang K, Liao CD, Prakash S, Conway M, Cheng HF (2018) Interlaboratory validation of a stable isotope dilution and liquid chromatography tandem mass spectrometry method for the determination of aflatoxins in milk, milk-based infant formula, and feed. J AOAC Int 101:677–685
Zhao Y, Huang J, Ma L, Wang F (2017) Development and validation of a simple and fast method for simultaneous determination of aflatoxin B1 and sterigmatocystin in grains. Food Chem 221:11–17
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this chapter
Cite this chapter
Jager, A.V., Tonin, F.G. (2021). Analytical Methods for Detection and Quantification of Aflatoxins. In: Hakeem, K.R., Oliveira, C.A.F., Ismail, A. (eds) Aflatoxins in Food. Springer, Cham. https://doi.org/10.1007/978-3-030-85762-2_8
Download citation
DOI: https://doi.org/10.1007/978-3-030-85762-2_8
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-85761-5
Online ISBN: 978-3-030-85762-2
eBook Packages: Biomedical and Life SciencesBiomedical and Life Sciences (R0)