Abstract
This work relies on the constructal design method associated with exhaustive search and genetic algorithms to perform geometric optimization of an asymmetric tri-forked pathway of highly conductive materials (inserts) that remove a constant heat flux from a body and deliver it to three isothermal heat sinks. It is shown numerically that the global thermal resistance, represented by the maximum excess of temperature, can be minimized by means of geometric evaluation subject to two constraints, the total rectangular area where the forked pathway is circumscribed and the tri-forked pathway area, and seven degrees of freedom. A parametric study is performed to show the influence of the degrees of freedom over the global thermal resistance. The optimal geometry was obtained for a 40% area fraction, leading to a maximum excess temperature seven-times minimized with a thermal performance 627% better than a once optimized architecture, showing the importance of the design for thermal performance. For higher values of aspect ratio, height/length, the optimal configuration is highly asymmetrical, while for lower ratios the bifurcated branches has low influence over the thermal performance of the system. The optimal tri-forked pathway presented a 307% lower thermal global resistance compared to a V-shaped pathway on the same conditions.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bejan, A. and Lorente, S., The Constructal Law and the Evolution of Design in Nature, Phys. Life Rev., 2011, vol. 8, no. 3, pp. 209–240.
Bejan, A. and Zane, J.P., Design in Nature, New York: Doubleday, 2012.
Bejan, A. and Lorente, S., Design with Constructal Theory, Hoboken:Wiley, 2008.
Bejan, A., Shape and Structure, from Engineering to Nature, Cambridge: Cambridge University Press, 2000.
Bejan, A., Lorente, S., and Lee, J., Unifying Constructal Theory of Tree Roots, Canopies and Forests, J. Theor. Biol., 2008, vol. 254, no. 3, pp. 529–540.
Reis, A.H. and Bejan, A., Constructal Theory ofGlobal Circulation and Climate, Int. J. HeatMass Transfer, 2006, vol. 49, nos. 11/12, pp. 1857–1875.
Miguel, A.F., The Emergence of Design in Pedestrian Dynamics: Locomotion, Self-Organization, Walking Paths and Constructal Law, Phys. Life Rev., 2013, vol. 10, no. 2, pp. 168–190.
Bejan, A. and Merkx, G.W., Constructal Theory of Social Dynamics, New York: Springer, 2007.
Bejan, A., The Physics of Life: The Evolution of Everything, New York: St.Martins Press, 2016.
Bejan, A., Evolution in Thermodynamics, Appl. Phys. Rev., 2017, vol. 4, no. 1, p. 011305.
Bejan, A., Maxwell’s Demons Everywhere: Evolving Design as the Arrow of Time, Sci. Rep., 2014, vol. 4, p. 4017.
Rodrigues, M.K., da S. Brum, R., Vaz, J., Rocha, L.A.O., dos Santos, E.D., and Isoldi, L.A., Numerical Investigation about the Improvement of the Thermal Potential of an Earth-Air Heat Exchanger (EAHE) Employing the Constructal DesignMethod, Renew. Energy, 2015, vol. 80, pp. 538–551.
Vieira, R.S., Petry, A.P., Rocha, L.A.O., Isoldi, L.A., and dos Santos, E.D., Numerical Evaluation of a Solar Chimney Geometry for Different Ground Temperatures by Means of Constructal Design, Renew. Energy, 2017, vol. 109, pp. 222–234.
Bello-Ochende, T., Olakoyejo, O.T., Meyer, J.P., Bejan, A., and Lorente, S., Constructal Flow Orientation in Conjugate Cooling Channels with Internal Heat Generation, Int. J. Heat Mass Transfer, 2013, vol. 57, pp. 241–249.
Teixeira, F.B., Lorenzini, G., Errera, M.R., Rocha, L.A.O., Isoldi, L.A., and dos Santos, E.D., Constructal Design of Triangular Arrangements of Square Bluff Bodies under Forced Convective Turbulent Flows, Int. J. Heat Mass Transfer, 2018, vol. 126, pp. 521–535.
Helbig, D., da Silva, C.C.C., Real, M. de V., dos Santos, E.D., Isoldi, L.A., and Rocha, L.A.O., Study about Buckling Phenomenon in Perforated Thin Steel Plates Employing ComputationalModeling and Constructal Design Method, Lat. Am. J. Solids Struct., 2016, vol. 13, pp. 1912–1936.
Martins, J.C., Goulart,M.M., Gomes, M. das, N., Souza, J.A., Rocha, L.A.O., Isoldi, L.A., and dos Santos, E.D., Geometric Evaluation of theMain Operational Principle of an OvertoppingWave Energy Converter by Means of Constructal Design, Renew. Energy, 2018, vol. 118, pp. 727–741.
Feijó, B.C., Lorenzini, G., Isoldi, L.A., Rocha, L.A.O., Goulart, J.N.V., and dos Santos, E.D., Constructal Design of Forced Convective Flows in Channels with Two Alternated Rectangular Heated Bodies, Int. J. Heat Mass Transfer, 2018, vol. 125, pp. 710–721.
Bejan, A. and Almogbel, M., Constructal T-Shaped Fins, Int. J. Heat Mass Transfer, 2000, vol. 43, no. 12, pp. 2101–2115.
Lorenzini, G. and Rocha, L.A.O., Constructal Design of Y-Shaped Assembly of Fins, Int. J. Heat Mass Transfer, 2006, vol. 49, no. 23, pp. 4552–4557.
Lorenzini, G. and Rocha, L.A.O., Constructal Design of T-Y Assembly of Fins for an Optimized Heat Removal, Int. J. Heat Mass Transfer, 2009, vol. 52, no. 5, pp. 1458–1463.
Xie, Z., Chen, L., and Sun, F., Constructal Optimization of Twice Y-Shaped Assemblies of Fins by Taking Maximum Thermal Resistance Minimization as Objective, Sci. China Technol. Sci., 2010, vol. 53, no. 10, pp. 2756–2764.
Lorenzini, G., Biserni, C., and Rocha, L.A.O., Constructal Design of X-Shaped Conductive Pathways for Cooling a Heat-Generating Body, Int. J. HeatMass Transfer, 2013, vol. 58, no. 1, pp. 513–520.
Hajmohammadi, M.R., Abianeh, V.A., Moezzinajafabadi, M., and Daneshi, M., Fork-Shaped Highly Conductive Pathways forMaximum Cooling in a HeatGenerating Piece, Appl. Therm. Eng., 2013, vol. 61, no. 2, pp. 228–235.
Horbach, C.S., dos Santos, E.D., Isoldi, L.A., and Rocha, L.A.O., Constructal Design of Y-Shaped Pathways for Cooling a Heat-Generating Body, Defect Diffus. Forum, 2014, vol. 348, no. 1, pp. 245–260.
Cheng, C.H. and Chen, Y.F., Topology Optimization of Heat Conduction Paths by a Non-Constrained Volume-of-Solid Function Method, Int. J. Therm. Sci., 2014, vol. 78, pp. 16–25.
Lorenzini, G., Barreto, E.X., Beckel, C.C., Schneider, P.S., Isoldi, L.A., dos Santos, E.D., and Rocha, L.A.O., Constructal Design of I-Shaped High Conductive Pathway for Cooling a Heat-GeneratingMedium Considering the Thermal Contact Resistance, Int. J. HeatMass Transfer, 2016, vol. 93, pp. 770–777.
Lorenzini, G., Barreto, E.X., Beckel, C.C., Schneider, P.S., Isoldi, L.A., dos Santos, E.D., and Rocha, L.A.O., Geometrical Evaluation of T-Shaped High Conductive Pathway with Thermal Contact Resistance for Cooling of Heat-Generating Medium, Int. J. Heat Mass Transfer, 2017, vol. 108, pp. 1884–1893.
You, J., Feng, H., Chen, L., and Xie, Z., Heat Conduction Constructal Optimization for Nonuniform Heat Generating Area Based on Triangular Element, Int. J. Heat Mass Transfer, 2018, vol. 117, pp. 896–902.
Cetkin, E. and Oliani, A., The Natural Emergence of Asymmetric Tree-Shaped Pathways for Cooling of a Non-Uniformly Heated Domain, J. Appl. Phys., 2015, vol. 118, no. 2, p. 024902.
Estrada, E. da. S.D., Fagundes, T.M., Isoldi, L.A., dos Santos, E.D.,Xie,G., and Rocha, L.A.O., Constructal Design Associated to Genetic Algorithm of Asymmetric V-Shaped Pathways, J. Heat Transfer, 2015, vol. 137, no. 6, p. 061010.
MATLAB, 2000, User’s Guide, Vers. 6.0.088, Release 12, Natick,MA: The Mathworks, 2000.
Reddy, J.N. and Gartling, D.K., The Finite Element Method in Heat Transfer and Fluid Dynamics, Florida: CRC, 1994.
Gosselin, L., Tye-Gingras, M., and Mathieu-Potvin, F., Review of Utilization of Genetic Algorithms in Heat Transfer Problems, Int. J. Heat Mass Transfer, 2009, vol. 52, nos. 9/10, pp. 2169–2188.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fagundes, T.M., Lorenzini, G., Estrada, E. et al. Constructal Design of Conductive Asymmetric Tri-Forked Pathways. J. Engin. Thermophys. 28, 26–42 (2019). https://doi.org/10.1134/S181023281901003X
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S181023281901003X