Abstract
This paper presents a systematic and practical method for constructing accurate computer and physical models that can be employed for the study of human tooth mechanics. The proposed method starts with a histological section preparation of a human tooth. Through tracing outlines of the tooth on the sections, discrete points are obtained and are employed to construct B-spline curves that represent the exterior contours and dentino-enamel junction (DEJ) of the tooth using a least square curve fitting technique. The surface skinning technique is then employed to quilt the B-spline curves to create a smooth boundary and DEJ of the tooth using B-spline surfaces. These surfaces are respectively imported into SolidWorks via its application protocol interface to create solid models. The solid models are then imported into Pro/MECHANICA Structure for finite element analysis (FEA). The major advantage of the proposed method is that it first generates smooth solid models, instead of finite element models in discretized form. As a result, a more advanced p-FEA can be employed for structural analysis, which usually provides superior results to traditional h-FEA. In addition, the solid model constructed is smooth and can be fabricated with various scales using the solid freeform fabrication technology. This method is especially useful in supporting bioengineering applications, where the shape of the object is usually complicated. A human maxillary second molar is presented to illustrate and demonstrate the proposed method. Note that both the solid and p-FEA models of the molar are presented. However, comparison between p- and h-FEA models is out of the scope of the paper. © 2003 Biomedical Engineering Society.
PAC2003: 8719Rr, 8718Bb, 8710+e
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Adobe Systems Incorporated. Adobe Photoshop 4.0 User Guide. Adobe Systems Incorporated, 345 Park Avenue, San Jose, CA, 1996.
ANSYS User's Manual, V5.4, ANSYS, Inc., Southpointe 275 Technology Drive, Canonsburg, PA 15317, 1995.
Aritan, S., P. Dabnichki, and R. Barlett. Program for generation of three-dimensional finite element mesh from magnetic resonance imaging scans of human limbs. Med. Eng. Phys.19:681–689, 1997.
Atmaram, G. H.Estimation of physiological stress with a natural tooth considering fibrous PDL structure. J. Dent. Res.60:873–877, 1981.
Beer, H. J., M. Bornitz, H. J. Hardtke, R. Schmidt, G. Hofmann, U. Vogel, T. Zahnert, and K. B. Hüttenbrink. Modeling of components of the human middle ear and simulation of their dynamic behavior. Audiology & Neuro-Otology4:156–162, 1999.
Chang, K. H., and K. K. Choi. A geometry-based parameterization method for shape design of elastic solids. Mech. Struct. & Mach.20:215–252, 1992.
Corby, T. W. Frozen-stress photoelastic analysis of rapid prototype stereolithography models. Measurement Group, Inc., P. O. Box 27777, Raleigh, NC 27611, 1998.
Goel, V. K., S. C. Khera, J. L. Ralston, and K. H. Chang. Stresses at the dentinoenamel junction of human teeth—A finite element investigation. J. Prosthet. Dent.66:451–460, 1991.
Hwang, H-Y., K. K. Choi, and K. H. Chang. Shape design sensitivity and optimization using p-version design modeling and finite element analysis. Mech. Struct. & Mach.25:103–137, 1997.
Ibrahim, Z. CAD/CAM Theory and Practice. New York: McGraw-Hill, 1991.
Jacobs, P. F. StereoLithography and Other RP&M Technologies. New York: ASME, 1994.
Kruth, J. P., and A. Kerstens. Reverse engineering modeling of free-form surfaces from point clouds subject to boundary conditions. J. Mater. Process. Technol.76:120–127, 1998.
Kumaresan, S., N. Yoganandan, F. A. Pintar, and D. J. Maiman. Finite element modeling of the cervical spine: Role of intervertebral disc under axial and eccentric loads. Med. Eng. Phys.21:689–700, 1999.
Mole, C., H. Gerard, J. L. Mallet, J. F. Chassagne, and N. Miller. A new three dimensional treatment algorithm for complex surfaces: Applications in surgery. J. Oral Maxillofac. Surg.53:158–162, 1995.
Mortenson, M. E. Geometric Modeling. New York: Wiley, 1985.
Parametric Technology Corporation. Release 2000i Pro/Mechanica Structure. Waltham, MA, 1999.
Raindrop Geomagic, Inc. Geomagic Studio 3, Raindrop Geomagic. Research Triangle Park, NC 27709, 2000.
Solidscape, Inc. ModelMaker II User's Manual. Merrimack, NH, 1988.
SolidWorks Corporation. SolidWorks 2001 User's Guide. 150 Baker Avenue Ext., Concord, MA 01742, 2001.
Stokes, H. Solid modeling and product exchange using STEP (PDES/STEP). Handbook of Solid Modeling, edited by D. E. LaCourse. New York: McGraw-Hill, 1995, Chap. 22
Szabó, B., and I. Babuška. Finite Element Analysis. New York: Wiley, 1991.
Tang, P. S. Integration of topology and shape optimizations for design of structural components. MS thesis. The University of Oklahoma, Norman, OK, 1999.
The Math Works Inc. MATLAB Version 5 User's Guide. Englewood Cliffs, NJ: Prentice Hall, 1997.
Vesely, I., B. Eickmeier, and G. Cambell. Automated 3–D reconstruction of vascular structures from high definition casts. IEEE Trans. Biomed. Eng.38:1123–1129, 1991.
Vincent, H. C., B. Colin, and W. V. Geoffrey. Automating laser scanning of 3D surfaces for reverse engineering. 3204:156–164, 1997.
Wheeldon, J., S. Kumaresan, N. Yoganandan, and F. A. Pintar. Finite element model of human cervical spinal column. Biomed. Sci. Instrum.36:337–342, 2000.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Chang, KH., Magdum, S., Khera, S.C. et al. An Advanced Approach for Computer Modeling and Prototyping of the Human Tooth. Annals of Biomedical Engineering 31, 621–631 (2003). https://doi.org/10.1114/1.1568117
Issue Date:
DOI: https://doi.org/10.1114/1.1568117