Abstract
The monitoring of structures has undergone important advances with the improvements of digital cameras available on the market. Thus, the Digital Image Correlation (DIC) technique has become a viable way of studying engineering problems. Recently it has been used in the debonding failure process between the reinforcement and the substrate. The methods or methodologies that should be followed to obtain the results associated to the debonding phenomenon using the DIC technique need to be better understood and studies on this topic are scarce. The present work therefore proposes a new and inexpensive method to monitor the interfacial behaviour between a reinforcement material and a substrate by combining the use of the DIC technique and a simplified nonlinear bond-slip model. For the validation of the proposed method, a series of single-lap shear tests with a sufficient long bond length carried out by the authors are used. Based on the slip distribution obtained from the DIC technique, it was found that a third-degree polynomial function can be used to approximate the interfacial bond-slip curve of the joint. The validation of the model is made with several analytical solutions using the proposed bond-slip model.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
C. Czaderski, K. Soudki, M. Motavalli, Front and side view image correlation measurements on FRP to concrete pull-off bond tests, J. Compos. Constr. 14 (4) (2010) 451–463.
G. Almeida, et al., Displacement measurements with ARPS in T-Beams load tests, in: Technological Innovation for Sustainability, Springer. 349 AICT, 2011, pp. 286–293.
T. Gajewski, T. Garbowski, Calibration of concrete parameters based on digital image correlation and inverse analysis, Arch. Civil Mech. Eng. 14 (1) (2014) 170–180.
E. Martinelli, C. Czaderski, M. Motavalli, Modeling in-plane and out-of-plane displacement fields in pull-off tests on FRP strips, Eng. Struct. 33 (2011) 3715–3725.
B. Ghiassi, et al., Application of digital image correlation in investigating the bond between FRP and masonry, Compos. Struct. 106 (2013) 340–349.
H. Zhu, et al., Digital image correlation measurement of the bond-slip relationship between fiber-reinforced polymer sheets and concrete substrate, J. Reinf. Plast. Compos. 33 (17) (2014) 1590–1603.
J.R. Cruz, et al., Bond behaviour of NSM CFRP-concrete systems: adhesive and CFRP cross-section influences, in: 8th International Conference on Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering (CICE2016), 2016.
G. Almeida, et al., In-plane displacement and strain image analysis, Comput. Aided Civil Infrastruct. Eng. 31 (4) (2016) 292–304.
H.C. Biscaia, N. Franco, C. Chastre, Stainless steel bonded to concrete: an experimental assessment using the DIC technique, Int. J. Concr. Struct. Mater. 12 (2018) 9.
Z. Wang, M.P. Vo, Short manual of the advanced digital image correlation function in the MOIRE Software Package, 2012, pp. 1–5. http://www.dropbox.com/s/dp7a2hspee8neak/2DDIC_manual.pdf?dl=0 (accessed October 8).
http://www.ncorr.com (accessed October 8).
GOM Correlate software (accessed October 8 at http://www.gom.com/3d-software/gom-correlate.html).
J. Dai, T. Ueda, Y. Sato, Unified analytical approaches for determining shear bond characteristics of FRP-concrete interfaces through pullout tests, J. Adv. Concr. Technol. 4 (1) (2016) 133–145.
U. Neubauer, F.S. Rostásy, Design aspects of concrete structures strengthened with externally bonded CFRP-plates, in: Proceedings of the 7th International Conference on Structural Faults and Repairs, vol. 2, 1997, 109–118.
J. Dai, T. Ueda, Y. Sato, Development of the nonlinear bond stress-slip model of fiber reinforced plastics sheet-concrete interfaces with a simple method, J. Compos. Constr. 9 (1) (2005) 52–62.
M. Aiello, M. Leone, Interface analysis between FRP EBR system and concrete, Compos. B: Eng. 39 (4) (2008) 618–626.
H.C. Biscaia, et al., Experimental evaluation of bonding between CFRP laminates and different structural materials, J. Compos. Constr. 3 (2016) 04015070.
D.S. Yang, S.N. Hong, S.K. Park, Experimental observation on bondslip behavior between concrete and CFRP plate,, Int. J. Concr. Struct. Mater. 1 (1) (2007) 37–43.
L. Lorenzis, B. Miller, A. Nanni, Bond of fiberreinforced polymer laminates to concrete, ACI Mater. J. 98 (3) (2001) 256–264.
K. Nakaba, et al., Bond behavior between fiber-reinforced polymer laminates and concrete, ACI Struct. J. 98 (3) (2001) 359–367.
H.C. Biscaia, C. Chastre, M.A.G. Silva, Nonlinear numerical analysis of the debonding failure process of FRP-to-concrete interfaces, Compos. B: Eng. 50 (2013) 210–223.
W. Wu, J. Yin, Fracturing behaviors of FRP-strengthened concrete structures, Eng. Fract. Mech. 70 (2003) 1339–1355.
H.C. Biscaia, C. Chastre, M.A.G. Silva, Bond-slip model for FRP-to-concrete bonded joints under external compression, Compos. B: Eng. 80 (2015) 246–259.
H.C. Biscaia, et al., Numerical analysis of FRP anchorage zones with variable width, Compos. B: Eng. 67 (2014) 410–426.
H.C. Biscaia, et al., Delamination process analysis of FRP-to-parent material bonded joints with and without anchorage systems using the distinct element method, Comp. Struct. 116 (2014) 104–119.
E. Dehghani, et al., A new bond-slip model for adhesive in CFRP-steel composite systems, Eng. Struct. 34 (2012) 447–454.
H.C. Biscaia, C. Chastre, A. Viegas, A new discrete method to model unidirectional FRP-to-parent material bonded joints subjected to mechanical loads, Comp. Struct. 121 (2015) 280– 295.
H. Yuan, et al., Full-range behavior of FRP-to-concrete bonded joints, Eng. Struct. 26 (2003) 553–565.
J.G. Teng, H. Yuan, J.F. Chen, FRP-to-concrete interfaces between two adjacent cracks: theoretical model for debonding failure, Int. J. Solids Struct. 43 (2006) 5750–5778.
H.C. Biscaia, C. Chastre, M.A.G. Silva, Linear and nonlinear analysis of bondslip models for interfaces between FRP composites and concrete, Compos. B: Eng. 45 (1) (2013) 1554–1568.
B. Ferracuti, M. Savoia, C. Mazzotti, Interface law for FRP-concrete delamination, Compos. Struct. 80 (4) (2007) 523–531.
H.C. Biscaia, et al., A nonlinear analytical model to predict the full-range debonding process of FRP-to-parent material interfaces free of any mechanical anchorage devices, Compos. Struct. 138 (2016) 52–63.
H.C. Biscaia, et al., Mechanical response of anchored FRP bonded joints: a nonlinear analytical approach, Mech. Adv. Mater. Struct. 25 (3) (2018) 238–252.
J.F. Chen, H. Yuan, J.G. Teng, Debonding failure along a softening FRP-to-concrete interface between two adjacent cracks in concrete, Eng. Struct. 29 (2) (2007) 259–270.
H.C. Biscaia, et al., Numerical modelling of the effects of elevated service temperatures on the debonding process of FRP-to-concrete bonded joints, Compos. B: Eng. 70 (2015) 64–79.
H.C. Biscaia, M.A.G. Silva, C. Chastre, Factors influencing the performance of externally bonded reinforcement systems of GFRP-to-concrete interfaces, Mater. Struct. 48 (9) (2015) 2961– 2981.
Y. Yongming, et al., Bond characteristics of CFRP-to-steel joints, J. Constr. Steel Res. 138 (2017) 401–419.
M.B. Ouezdou, A. Belarbi, S.W. Bae, Effective bond length of FRP sheets externally bonded to concrete, Int. J. Concr. Struct. Mater. 3 (2) (2009) 127–131.
A. Hosseini, D. Mostofinejad, Effective bond length of FRP-to-concrete adhesively-bonded joints: Experimental evaluation of existing models, Int. J. Adhes. Adhes. 48 (2014) 150–158.
H.M. Diab, O.A. Farghal, Bond strength and effective bond length of FRP sheets/plates bonded to concrete considering the type of adhesive layer, Compos. B: Eng. 58 (2014) 618–624.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Biscaia, H.C., Franco, N. & Chastre, C. Development of a simple bond-slip model for joints monitored with the DIC technique. Archiv.Civ.Mech.Eng 18, 1535–1546 (2018). https://doi.org/10.1016/j.acme.2018.06.009
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1016/j.acme.2018.06.009