Abstract
This paper presents method of oil pockets creation by the burnishing (embossing) technique. Steel and ceramic forming elements were used to modify sliding surfaces. This technique allows to obtain dimples in a wide dimensional range and regular arrangement. Dimples array on machined surface depends on the forming element shape and many machining factors. Examples of textured cylinder liners surface topographies are shown. The computer software for visualization of oil pockets array on machined surface is presented in this paper.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
B. Nilsson, B.-G. Rosen, T.R. Thomas, D. Wiklund, L. Xiao, Oil pockets and surface topography: mechanism of friction reduction, in: Proceedings of the XI International Colloquium on Surfaces, Chemnitz, 2004, Addendum.
I. Etsion, State of the art in laser surface texturing, in: Proceedings of the 12th Conference on Metrology and Properties of Engineering Surfaces, Rzeszów, 2009, pp. 7–20.
W. Koszela, P. Pawlus, L. Galda, The effect of oil pockets size and distribution on wear in lubricated sliding, Wear 263 (2007) 1585–1592.
P. Pawlus, Effects of honed cylinder surface topography on the wear of piston-piston ring—cylinder assemblies under artificially increased dustiness condition, Tribology International 26 (1993) 49–56.
D.K. Srivastava, A.K. Agarwal, J. Kumar, Effect of liner surface properties on wear and friction in a non-firing engine simulator, Materials & Design 28 (5) (2007) 1632–1640.
J. Michalski, P. Woś, The effect of cylinder liner surface topography on abrasive wear of piston-cylinder assembly in combustion engine, Wear 271 (2011) 582–589.
S. Johansson S P.H. Nilsson, R. Ohlsson, C. Anderberg, B.-G. Rosen, New cylinder liner surfaces for low oil consumption, Tribology International 41 (2008) 854–859.
S.H. Hill, Cylinder liner finishes and their effect on oil consumption, SAE International (2001) No. 2001-01-3550.
S. Brinkman, H. Bodschwinna, Characterisation of automotive bore performance using 3D surface metrology, in: L. Blunt, X. Jiang (Eds.), Advanced Techniques for Assessment Surface Topography, Kogan Page Science, London and Sterling, 2003.
U. Klink, Laserhonen fur Zylinderlaufbagnen, Motortechnische Zeitschrift 58 (9) (1997) 554–556.
A. Robota, F. Zwein, Einfluss der Zylinderlaufflachentopografie auf den Ölverbrauch und die Partikel-Emissionen eines DI-Dieselmotors, Motortechnische Zeitschrift 60 (4) (1999) 246–255.
G. Duffet, P. Sallamand, A.B. Vannes, Improvement in friction by cw Nd: YAG laser surface treatment on cast iron cylinder bore, Applied Surface Science 205 (2003) 289–296.
E. Tomanik, Friction and wear bench tests of difference engine liner surface finishes, Tribology International 41 (2008) 1032–1038.
W. Grabon, W. Koszela, P. Pawlus, S. Ochwat, Improving tribological performance of piston ring—cylinder liner frictional pair by liner surface texturing, Tribology International 61 (2013) 102–108.
W. Koszela, L. Galda, A. Dzierwa, P. Pawlus, The effect of surface texturing on seizure resistance of steel-bronze assembly, Tribology International 43 (2010) 1933–1942.
L. Galda, A. Dzierwa, J. Sep, P. Pawlus, The effect of oil pockets shape and distribution on seizure resistance in lubricating sliding, Tribology Letters 37 (2010) 301–311.
L. Blunt, X. Jiang, Numerical parameters for characterisation of topography, in: L. Blunt, X. Jiang (Eds.), Advanced techniques for assessment surface topography, Kogan Page, London, 2003, pp. 17–41.
A. Kovalchenko, O. Ajayi, A. Erdemir, G. Fenske, I. Etsion, The effect of laser surface texturing on transitions in lubrication regimes during unidirectional sliding contact, Tribology International 38 (2005) 219–225.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Koszela, W., Pawlus, P., Rejwer, E. et al. Possibilities of oil pockets creation by the burnishing technique. Archiv.Civ.Mech.Eng 13, 465–471 (2013). https://doi.org/10.1016/j.acme.2013.03.004
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1016/j.acme.2013.03.004