Abstract
An alloyed cast iron was prepared by horizontal continuous casting. To study the salt bath temperature on microstructure and mechanical properties, the alloyed cast iron was firstly austenitized at 950 °C for 3 h and then austempered in salt bath at various temperatures (250 °C, 300 °C and 350 °C) for another 3 h. The scanning electron microscopy (SEM), electron backscattered diffraction (EBSD), and X-ray diffraction (XRD) were employed to observe the microstructure and test the mechanical properties of the alloyed cast iron. Results show that the microstructure of the alloyed cast iron is mainly composed of acicular or feathery ferrite (bainite), retained austenite, carbide, and graphite. When austempered in salt bath at 250 °C, 300 °C and 350 °C for 3 h, the volume fractions of retained austenite are 33.1%, 41.7%, and 57.2%, the thickness of acicular ferrite are 0.25 µm, 0.3 µm, and 0.8 µm. As the salt bath austempering temperature increases, the mechanical properties decrease due to the increase of the volume fraction of retained austenite and the thickness of acicular ferrite. The highest tensile strength of the alloyed cast iron is achieved when it is austempered at 250 °C in a salt bath. Under these conditions, the tensile strength of the alloyed cast iron can reach 1,429 MPa. Tensile test results indicate that the fracture mechanism is predominantly brittle fracture.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Meng F, Huang H, Yuan X, et al. Segregation in squeeze casting 6061 aluminum alloy wheel spokes and its formation mechanism. China Foundry, 2021, 18(1): 45–51.
Varshney D, Kumar K. Application and use of different aluminium alloys with respect to workability, strength and welding parameter optimization. Ain Shams Engineering Journal, 2021, 12(1): 1143–1152.
Zhou W, Shao Z, Yu J, et al. Advances and trends in forming curved extrusion profiles. Materials, 2021, 14(7): 1603.
Zhang W, Xu J. Advanced lightweight materials for automobiles: A review. Materials & Design, 2022: 110994.
Terčelj M, Smolej A, Fajfar P, et al. Laboratory assessment of wear on nitrided surfaces of dies for hot extrusion of aluminium. Tribology International, 2007, 40(2): 374–384.
Krahmer D M, Egea A J S, Celentano D, et al. Friction characterization when combining laser surface texturing and graphite-based lubricants. Journal of Materials Research and Technology, 2020, 9(2): 1759–1767.
Saal P, Meier L, Li X, et al. In situ study of the influence of nickel on the phase transformation kinetics in austempered ductile iron. Metallurgical and Materials Transactions: A, 2016, 47: 661–671.
Li Y, Li P, Wang K, et al. Microstructure and mechanical properties of a Mo alloyed high chromium cast iron after different treatments. Vacuum, 2018, 156: 59–67.
Mohammadnezhad M, Javaheri V, Shamanian M, et al. Effects of vanadium addition on microstructure, mechanical properties and wear resistance of Ni-Hard4 white cast iron. Materials & Design, 2013, 49: 888–893.
Bartosiewicz L, Singh I, Alberts F A, et al. The influence of chromium on mechanical properties of austempered ductile cast iron. Journal of Materials Engineering and Performance, 1995, 4: 90–101.
Du Y, Gao X, Wang X, et al. Tribological behavior of austempered ductile iron (ADI) obtained at different salt bath austempering temperatures. Wear, 2020, 456: 203396.
Sellamuthu P, Samuel D G H, Dinakaran D, et al. Austempered ductile iron (ADI): Influence of salt bath austempering temperature on microstructure, mechanical and wear properties and energy consumption. Metals, 2018, 8(1): 53.
Sarkar T, Bose P, Sutradhar G. Mechanical and tribological characteristics of copper alloyed austempered gray cast iron (AGI). Materials Today: Proceedings, 2018, 5: 3664–3673.
Leem D S, Lee Y D, Jun J H, et al. Amount of retained austenite at room temperature after the reverse of martensite to austenite in a Fe-13% Cr-7% Ni-3% Si martensitic stainless steel. Scripta Materialia, 2001, 45(7): 767–772.
Roberts C S. Effect of carbon on the lattice parameter of austenite. Transactions of the AIME, 1982, 197: 203–204.
Neri M A, R Colás, Valtierra S. Graphitization in high carbon commercial steels. Journal of Materials Engineering and Performance, 1998, 7(4): 467–473.
Friedberg J, Hillert M. Ortho-pearlite in silicon steels. Acta Metallurgica, 1970, 18(12): 1253–1260.
Zhu X D, Li C J, Zhang S H, et al. TEM investigation on microstructures of eutectoid cementite in high carbon low alloy steels. Acta Metallurgica Sinica, 1998, 34(1): 31–38.
Lee Y K, Shin H C, Jang Y C, et al. Effect of austenitizing temperature on the amount of retained austenite and its thermal stability in a bainite Fe-3% Si-0.45% C-X steel. Scripta Materialia, 2002, 47(12): 805–809.
Zaefferer S, Ohlert J, Bleck W. A study of microstructure, mechanisms and correlation between microstructure and mechanical properties of low alloyed TRIP steel. Acta Materialia, 2004, 52(9): 2765–2778.
Brozzo P, Buzzichelli G, Mascanzoni A, et al. Microstructure and cleavage resistance of low-carbon bainite steels. Metal Science, 1977, 11(4): 123–130.
Hutchinson B, Komenda J, Rohrer G S, et al. Heat-affected zone microstructures and their influence on toughness in two micro-alloyed HSLA steels. Acta Materialia, 2015, 97: 380–391.
Hu H, Xu G, Nabeel M, et al. In situ study on interrupted growth behavior and crystallography of bainite. Metallurgical and Materials Transactions A, 2021, 52: 817–825.
Beladi H, Tari V, Timokhina I B, et al. On the crystallographic characteristics of nano-bainite steel. Acta Materialia, 2017, 127: 426–437.
Pradhan S K, Nayak B B, Sahay S S, et al. Mechanical properties of graphite flakes and spherulites measured by nanoindentation. Carbon, 2009, 47(9): 2290–2292.
Balos S, Radisavljevic I, Rajnovic D, et al. Geometry, mechanical and ballistic properties of ADI material perforated plates. Materials & Design, 2015, 83: 66–74.
Guo H, Feng X, Zhao A, et al. Effects of ausforming temperature on bainite transformation kinetics, microstructures and mechanical properties in ultra-fine bainitic steel. Journal of Materials Research and Technology, 2020, 9(2): 1593–1605.
Acknowledgments
This work was financially supported by the National Natural Science Foundation of China (Nos. U20A20235, 52171127), Guangdong East Northwest New R&D Institution Construction (No. 2019B090905009), Guangdong Aluminum Strip and Foil Processing Enterprise Research Institute (No. 2014B090903012).
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Additional information
Ji-lin Li Born in 1973, Ph.D., Professor. Research interests: Aluminum, magnesium light metal processing, performance research and interface analysis of advanced metal composite materials, and self-lubricating mold materials, especially for aluminum alloys.
E-mail: Li197307@163.com
Rights and permissions
About this article
Cite this article
Zheng, J., Li, Jl., Li, Sf. et al. Effect of salt bath temperature on microstructure and mechanical properties of an austempered alloyed cast iron. China Foundry (2024). https://doi.org/10.1007/s41230-024-4034-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s41230-024-4034-5