Abstract
A Ni-based composite coating reinforced by in situ synthesized TiB2 and TiC particles was fabricated on Ti6Al4V by laser cladding. An attempt was made to correlate the thermodynamic predictions and experimental observation. The microstructure and the microhardness profile across the coating were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and a hardness tester. It is found that the coating mainly consists of a large number of reinforcements (black blocky TiB2, flower-like or equiaxial TiC, and fine acicular CrB) and the γ matrix. The hardness of TiB2, TiC, and CrB reinforcements is much higher than that of the γ matrix. The dispersive distribution of such high hardness reinforcements causes the increase in hardness of the whole coating. The average value of the hardness is approximately Hv0.2 700 in the coating. The hardness of the coating is obviously higher than that of the substrate due to the dispersion strengthening of reinforcements.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
X.B. Liu and R.L. Yu, Effects of La2O3 on microstructure and wear properties of laser clad γ/Cr7C3/TiC composite coatings on TiAl intermatallic alloy, Mater. Chem. Phys., 101(2007), p 448.
J.J. Candel, V. Amigó, J.A. Ramos, and D. Busquets, Sliding wear resistance of TiCp reinforced titanium composite coating produced by laser cladding, Surf. Coat. Technol., 204(2010), p. 3161.
D.S. Wang, Z.J. Tian, L.D. Shen, Z.D. Liu, and Y.H. Huang, Research states of laser surface modification technology on titanium alloys, Laser Optoelectron. Prog., 45(2008), p 24.
J.D. Majumdar and L. Li, Development of titanium boride (TiB) dispersed titanium (Ti) matrix composite by direct laser cladding, Mater. Lett., 64(2010), p 1010.
Y.L. Yang, D. Zhang, W. Yan, and Y.R. Zheng, Microstructure and wear properties of TiCN/Ti coatings on titanium alloy by laser cladding, Opt. Laser Eng., 48(2010), p 119.
J. Nurminen, J. Näkki, and P. Vuoristo, Microstructure and properties of hard and wear resistant MMC coatings deposited by laser cladding, Int. J. Refract. Met. Hard Mater., 27(2009), p 472.
J. Li, Z,S. Yu, H.P. Wang, and M.P. Li, Microstructural evolution of titanium matrix composite coatings reinforced by in situ synthesized TiB and TiC by laser cladding, Int. J. Miner. Metall. Mater., 17(2010), p. 481.
Y.P. Pu, B.G. Guo, J.S. Zhou, S.T. Zhang, H.D. Zhou, and J.M. Chen, Microstructure and tribological properties of in situ synthesized TiC, TiN, and SiC reinforced Ti3Al intermetallic matrix composite coatings on pure Ti by laser cladding, Appl. Surf. Sci., 255(2008), p 2697.
B.G. Guo, J.S. Zhou, S.T. Zhang, H.D. Zhou, Y.P. Pu, and J.M. Chen, Phase composition and tribological properties of Ti-Al coatings produced on pure Ti by laser cladding, Appl. Surf. Sci., 253(2007), p 9301.
R. Banerjee, A. Genç, D. Hill, P.C. Collins, and H.L. Fraser, Nanoscale TiB precipitates in laser deposited Ti-matrix composites, Scripta Mater., 53(2005), p 1433.
Y. Wang and H.M. Wang, Wear resistance of laser clad Ti2Ni3Si reinforced intermetallic composite coatings on titanium alloy, Appl. Surf. Sci., 229(2004), p 81.
J. Li, W.G. Li, and H.Y. Zhang, Ni-based composite coatings reinforced by TiB2/WC synthesized in situ on stainless steel by laser cladding, Mater. Mech. Eng., 32(2008), p 34.
X.H. Wang, M. Zhang, Z.D. Zou and S.Y. Qu, Microstructure and properties of laser clad TiC + NiCrBSi + rare earth composite coatings, Surf. Coat. Technol., 161(2002), p 195.
R.L. Sun, J.F. Mao, and D.Z. Yang, Microstructural characterization of NiCr1BSiC laser clad layer on titanium alloy substrate, Surf. Coat. Technol., 150(2002), p. 199.
R.L. Sun, Y. Tang, and X.J. Yang, Microstructure and tribological properties of In-situ synthesized TiB2-TiC/ Ni based composite coating by laser cladding, Trans. Mater. Heat Treat., 25(2004), p 1000.
L.F. Cai, Y.Z. Zhang, and L.K. Shi, Microstructure and formation mechanism of titanium matrix composites coating on Ti-6Al-4V by laser cladding, Rare Met., 26(2007), p 342.
D.L. Ye and J.H. Hu, Practical Inorganic Thermodynamics Manual, Metallurgical Industry Press, Beijing, 2002, p. 57.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, J., Zhang, Xj., Wang, Hp. et al. Microstructure and mechanical properties of Ni-based composite coatings reinforced by in situ synthesized TiB2 + TiC by laser cladding. Int J Miner Metall Mater 20, 57–64 (2013). https://doi.org/10.1007/s12613-013-0693-8
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-013-0693-8