Abstract
Resistance spot welding (RSW) is a process in which contacting metal surfaces are joined by the pressure and heat obtained from resistance to electric current flow. It is widely accepted in the industry due to its advantages in high speed and suitability for automation. The RSW process is extremely important to quality in automotive industry because approximately 6000 spot welds were used in automotive body. In addition, the RSW process is a complicated process that includes electrical, thermal and mechanical phenomena. For this reason, it is necessary that researchers should perform electric field, heat transfer and thermo-elastic-plastic analysis, and consider phase change, contact conditions and temperature dependence of material properties in order to simulate a realistic RSW process. There were lots of previous studies for RSW simulation by using Finite element method (FEM), but most of studies have performed qualitative analysis which predicts the shape of weld nugget fatigue life and residual stress. Therefore, this study defines the contents which mentioned above based on the theoretical background and reproduces a 3D DC RSW process through using ABAQUS, commercial FEM program. It also obtains the reliability in terms of simulation results through quantitative approach by comparing between the nugget shape and the actual experimental results. The error percentage of nugget width between simulation and experiment shows outstanding results that from 0.44 % to 3.80 %. Based on the simulation results through these theoretical backgrounds, it is possible to effectively trace the weld nugget shape of all steels, provided the temperature dependent material properties are available. An illustration of such a simulation to predict the nugget shape and size of resistance spot welded SPRC 340 steel is presented in the paper.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Y. Yang and J. Kim, Analysis of weldment by using finite element method(3) -Residual stress and distortion in weldment, Journal of The Korean Welding and Joining Society, 29 (2011) 1–2.
K. Kim, Analysis and application of spot welding process by finite element method, Chung Ang University (2000).
Y. Yang, K. Son, S. Cho, S. Hong, S. Kim and K. Mo, Effect of residual stress on fatigue strength in resistance spot weldment, Transactions of the Korean Society of Mechanical Engineers, 25 (2001) 1713–1719.
K. Kim, K. Jang and S. Kang, Finite element modeling for prediction of nugget shape and residual stress in resistance spot welding, The Korean Welding and Joining Society Conference 1999 302–305.
B. Joo, H. Byun and B. Lee, Performance evaluation for the methods of spot weld modeling considering durability, Transactions of the Korean Society of Mechanical Engineers, 29 (2005) 1153–1160.
T. Kobayashi and Y. Mihara, Numerical simulation of nugget formation in spot welding, SIMULIA Community Conference (2014).
H. Eisazadeh, M. Hamedi and A. Halvaee, New parametric study of nugget size in resistance spot welding process using finite element method, Materials and Design, 31 (2010) 149–157.
H. A. Nied, The finite element modeling of the resistance spot welding process, Welding Research Supplement (1984) 123s–132s.
C. L. Tsai, O. A. Jammal, J. C. Papritan and D. W. Dickinson, Modeling of resistance spot weld nugget growth, Welding Research Supplement (1992) 47s–54s.
H. Zhigang, I.-S. Kim, W. Yuanxun, L. Chunzhi and C. Chuanyao, Finite element analysis for the mechanical features of resistance spot welding process, Journal of Materials Processing Technology, 185 (2007) 160–165.
I. R. Nodeh, S. Serahzadeh and A. H. Kokabi, Simulation of welding residual stresses in resistance spot welding, FE modeling and X-ray verification, Journal of Materials Processing Technology, 205 (2008) 60–69.
H. Zhigang, W. Yuanxun, L. Chunzhi and C. Chuanyao, A multi-coupled finite element analysis of resistance spot welding process, Acta Mechanica Solida Sinica, 19 (2006) 86–94.
J. Saleem, A. Majid, K. Bertilsson, T. Carlberg and N. U. Islam, Nugget formation during resistance spot welding using finite element model, International Science Index, Mechanical and Mechatronics Engineering, 6 (2012) 1228–1233.
Y. H. P. Manurung, N. Muhammad, E. Haruman, S. K. Abas, G. Tham, K. M. Salleh and C. Y. Chau, Investigation on weld nugget and HAZ development of resistance spot welding using SYSWELD’s customized electrode meshing and experimental verification, Asian Journal of Industrial Engineering, 2 (2010) 63–71.
O. Andersson, Process planning of resistance spot welding, KTH Industrial Engineering and Management (2013).
C. Srikunwong, T. Dupuy and Y. Bienvenu, Numerical simulation of resistance spot welding process using FEA technique, 13th International Conference on Computer Technology in Welding (2003).
J. A. Greenwood, Construction resistance and the real area of contact, British Journal of Applied Physics, 17 (1966) 1621–1632.
J. A. Greenwood and J. B. P. Williamson, Contact of nominally flat surfaces, Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences, 295 (1966) 300–319.
S. S. Babu, M. L. Santella, Z. Feng, B. W. Riemer and J. W. Cohron, Empirical model of effects of pressure and temperature on electrical contact resistance of metals, Science and Technology of Welding and Joining, 6 (3) (2001) 126–132.
Y. B. Li, X. M. Lai and G. L. Chen, The influence of interfacial thermal contact conductance on resistance spot weld nugget formation, Advanced Materials Research, 97-101 (2010) 3239–3242.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Young Whan Park
Jungho Cho received his Ph.D. at KAIST in 2007 and now he is a faculty of Chungbuk National University after working at Hyundai Motors and Ohio State University, USA for several years. His major is development of welding and joining techniques, welding physics and thermo-dynamical analysis of weld pool.
Rights and permissions
About this article
Cite this article
Lee, Y., Jeong, H., Park, K. et al. Development of numerical analysis model for resistance spot welding of automotive steel. J Mech Sci Technol 31, 3455–3464 (2017). https://doi.org/10.1007/s12206-017-0634-y
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-017-0634-y