Abstract
The temperature distribution in roller Linear motion (LM) rail surface heated with moving frictional heat source was investigated experimentally and numerically. The operating conditions which had not been regarded by previous research, such as the type of the LM guide and operating temperature, were taken into account for improving the previous model of friction force. Frictional heat generation model and heat partitioning coefficient were proposed to calculate the heat transferred to the LM rail. The numerical solutions were calculated in combining a heat conduction equation and the rate of frictional heat flowing into the rail. Frictional heat generation model and heat partitioning coefficient were verified by comparing experimental and numerical results. Simulation results showed that smaller LM block size or higher velocity leads to the higher temperature distribution in the rail surface. Results also indicated that larger motion stroke results in a lower and wider temperature distribution in the rail surface.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Y. S. Yi, Y. Y. Kim, J. S. Choi, J. H. Yoo, D. J. Lee, W. L. Suk and S. J. Lee, Dynamic analysis of a linear motion guide having rolling elements for precision devices, J. of Mechanical Science and Technology, 62 (2008) 50–60.
R. Ramesh, M. A. Mannan and A. N. Poo, Thermal error measurement and modeling in machine tools. Part I. Influence of varying operating conditions, Int. J. Mach. Tools Manuf., 43 (2003) 391–404.
C. H. Wu and Y. T. Kung, Thermal analysis for the feed drive system of a CNC machine center, Int. J. Mach. Tools Manuf., 43 (2003) 1521–1528.
Z. Z. Xu, X. J. Liu, H. K. Kim, J. H. Shin and S. K. Lyu, Thermal error forecast and performance evaluation for an air-cooling ball screw system, Int. J. Mach. Tools Manuf., 51 (2011) 605–611.
J. J. Kim, Y. H. Jeong and D. W. Cho, Thermal behavior of a machine tool equipped with linear motors, Int. J. Mach. Tools Manuf., 44 (2004) 749–758.
S. K. Lee, J. H. Yoo and M. S. Yang, Effect of thermal deformation on machine tool slide guide motion, Tribology Int., 36 (2003) 41–47.
N. S. Main, S. Fletcher, A. P. Longstaff and A. Myers, Efficient estimation by FEA of machine tool distortion due to environmental temperature perturbations, Precis. Eng., 37 (2013) 372–379.
E. Creighton, A. Honegger, A. Tulsian and D. Mukhopadhyay, Analysis of thermal errors in a high-speed micro- milling spindle, Int. J. Mach. Tools Manuf., 50 (2010) 386–393.
H. Wu, H. T. Zhang, Q. J. Guo, X. S. Wang and J. G. Yang, Thermal error optimization modeling and real-time compensation on a CNC turning center, J. Mater. Process. Technol., 207 (2008) 172–179.
C. Jin, B. Wu and Y. M. Hu, Heat generation modeling of ball bearing based on internal load distribution, Tribology Int., 45 (2012) 8–15.
K. D. Cole, C. M. Tarawneh, A. A. Fuentes, B. M. Wilson and L. Navarro, Thermal models of railroad wheels and bearings, Int. J. Heat Mass Transfer, 53 (2010) 1636–1645.
C. M. Tarawneh, K. D. Cole, B. M. Wilson and F. Alnaimat, Experiments and models for the thermal response of railroad tapered-roller bearings, Int. J. Heat Mass Transfer, 51 (2008) 5794–5803.
J. Takabi and M. M. Khonsari, Experimental testing and thermal analysis of ball bearings, Tribology Int., 60 (2013) 93–103.
D. J. Cheng, W. S. Yang, J. H. Park, T. J. Park, S. J. Kim, G. H. Kim and C. H. Park, Friction experiment of linear motion roller guide THK SRG25, Int. J. Precis. Eng. Manuf., 15 (3) (2014) 545–551.
M. Kasai, M. Fillon, J. Bouyer and S. Jarny, Influence of lubricants on plain bearing performance: Evaluation of bearing performance with polymer-containing oils, Tribology Int., 46 (2012) 190–199.
THK Linear Motion System Catalog, THK Co., Ltd, Tokyo, Japan, Sec. A-1 (2013) 412–441.
M. Amiri, M. M. Khonsari and S. Brahmeshwarkar, On the relationship between wear and thermal response in sliding systems, Tribology Lett, 38 (2010) 147–154.
J. Taylor, An introduction to error analysis: The study of uncertainties in physical measurements, 2nd ed., University Science Books (1997).
S. Fletcher and D. G. Goed, Measuring and modeling heat transfer and thermal errors on a ballscrew feed drive system, Trans. Eng. Science, 44 (2003) 349–359.
D. Hakan, Experimental and numerical studies of natural convection from horizontal concrete cylinder heated with a cylindrical heat source, Int. Comm. Heat Mass Transfer, 37 (2010) 422–429.
S. H. Jang, G. H. Kim and C. H. Park, Estimation of friction heat in a linear motion bearing using Box-Behnken design, Int. J. Adv. Manuf. Technol. (2016).
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended by Associate Editor Chang Yong Park
De-Jun Cheng is a Ph.D. candidate in Mechanical Engineering at the Gyeongsang National University. He received a B.S. from Huaihai Institute of Technology in 2011 and an M.S. in Mechanical Engineering from Gyeongsang National University in 2013. His research interests include tribology and heat and mass transfer.
Su-Jin Kim is a Professor of Mechanical Engineering at Gyeongsang National University. He received a B.S. in Agricultural Mechanical Engineering from Seoul National University in 1998 and an M.S. and Ph.D. in Mechanical Engineering from Korea Advanced Institute of Science and Technology in 2000 and 2005, respectively. His research interests include computeraided manufacturing and NC machining simulation.
Rights and permissions
About this article
Cite this article
Cheng, DJ., Park, JH., Suh, JS. et al. Effect of frictional heat generation on the temperature distribution in roller linear motion rail surface. J Mech Sci Technol 31, 1477–1487 (2017). https://doi.org/10.1007/s12206-017-0247-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12206-017-0247-5