Abstract
Investigations of the seismic behavior of steel reinforced concrete L-shaped columns under constant axial compression and cycled bending-shear-torsion load were performed. Six specimens, which considered two parameters, i.e., the moment ratio of torsion to bending (γ) and the aspect ratio (column length-to-depth ratio, ϕ), were prepared for the experiment. In this study, the failure process, torsion-displacement hysteresis curves, and flexure-displacement hysteresis curves were obtained. The failure characteristics, mechanical behavior of specimens such as the failure patterns, hysteresis curves, rigidity degradation, ductility and energy dissipation, are analyzed. The experimental research indicated that the major failures of the specimens were bending failure, bending-shear failure and bending-torsion failure as the moment ratio of torsion to bending (γ) increased. The torsion-displacement hysteresis curves were pinched in the middle, formed a slip platform, and the phenomenon of “load drop” occurred after the peak load. The bending-displacement hysteresis curves were plump, which showed that bending capacity of the specimen was better than its torsion capacity. Additionally, the energy dissipation of the specimen was dominated by torsion in the early stage and ultimately governed by the bending moment in the later phase. Test results also indicated that the displacement ductility coefficient and interstory rotation angle of the failure point were less than 3.0 and 1/50, respectively, which means the test specimen performance does not meet the requirement of the Chinese Code for Seismic Design of Buildings (GB 50011–2014) in this respect.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Arnold C (1980), “Building Configuration: Characteristics for Seismic Design,” Proceedings of the Seventh World Conference on Earthquake Engineering, 4: 589–592.
Arabzadeh H and Galal K (2018), “Seismic-Response Analysis of RC C-Shaped Core Walls Subjected to Combined Flexure, Shear, and Torsion,” Journal of Structural Engineering, 144(10).
Chen ZP, Xu JJ and Chen YL (2016), “Axial Compression Ratio Limit Values for Steel Reinforced Concrete (SRC) Special Shaped Columns,” Steel & Composite Structures, 20(2): 295–316.
Chen ZP, Xu JJ and Xue JY (2015), “Hysteretic Behavior of Special Shaped Columns Composed of Steel and Reinforced Concrete (SRC),” Earthquake Engineering and Engineering Vibration, 14(2): 329–345.
Chen ZP and Liu X (2018), “Seismic Behavior of Steel Reinforced Concrete Cross-Shaped Column Under Combined Torsion,” Steel and Composite Structures, 16(4): 407–420.
Chen SC, Peng W, Yan WM (2018), “Experimental Study on Steel Reinforced Concrete Columns Subjected to Combined Bending-Torsion Cyclic Loading,” Structural Design of Tall and Special Buildings, 27(11).
Duan XN and Chandler AM (2010), “Seismic Torsional Response and Design Procedures for a Class of Setback Frame Buildings,” Earthquake Engineering & Structural Dynamics, 24(5): 761–777.
ECN. Eurocode 8 (2004), Design of Structures for Earthquake Resistance — Part 1-General Rules, Seismic Actions and Rules for Buildings, European Committee for Standardization, Bruxelles, Belgium.
Fang L, Zhang B and Jin GF (2015), “Seismic Behavior of Concrete-Encased Steel Cross-Shaped Columns,” Journal of Constructional Steel Research, 109: 24–33.
Greene G and Belarbi A (2009), “Model for Reinforced Concrete Members under Torsion, Bending, and Shear. I: Theory,” Journal of Engineering Mechanics, 135(9): 970–977.
GB/T 50081-2002 (2002), Standard for Test Method of Mechanical Properties on Ordinary Concrete, China Building Industry Press, Beijing, China. (in Chinese)
GB/T228.1 (2010), Metallic Materials-Tensile Testing-Part 1 Method of Test at Room Temperature, China Standards Press, Beijing, China. (in Chinese)
GB50011-2014 (2014), Code for Seismic Design of Buildings, China Building Industry Press, Beijing, China. (in Chinese)
Hsu HL and Wang C (2000), “Flexural-Torsional Behaviour of Steel Reinforced Concrete Members Subjected to Repeated Loading,” Earthquake Engineering & Structural Dynamics, 29(5): 667–682.
Hsu HL, Hsieh JC and Juang J (2004), “Seismic Performance of Steel-Encased Composite Members with Strengthening Cross-Inclined Bars,” Journal of Constructional Steel Research, 60(3): 1663–1679.
IBC (2009), International Building Code, International Code Council, Inc, 12009.
Ji XD, Liu D, and Qian JR (2017), “Improved Design of Special Boundary Elements for T-Shaped Reinforced Concrete Walls,” Earthquake Engineering and Engineering Vibration, 16(1): 83–95.
Jurkowska N (2018), “Considering Nonlinear Properties of Concrete in the Design of Reinforced Concrete Structures for Torsion,” Materials Science and Engineering, 364(1): 1–9.
Kaushik S and Dasgupta K (2019), “Seismic Behavior of Slab-Structural Wall Junction of RC Building.” Earthquake Engineering and Engineering Vibration, 18(2): 331–349.
Koliopulos PK, Hsieh JC and Chandler AM (1995), “Stochastic Linearization of Inelastic Seismic Torsional Response: Formulation and Case Studies”, Engineering Structures, 17(7): 494–504.
Li B and Pham TP (2014), “Experimental Study on the Seismic Response of L-Shaped Reinforced Concrete Columns,” Structures Congress 2014, 1673–1682.
Li H (2011), “The Seismic Action Comparison Between Chinese, American, European and Japanese Seismic Design Codes for Buildings,” Master Dissertation, Harbin Institute of Technology, Harbin, China. (in Chinese)
Li Q and Belarbi A (2012), “Performance Based Design Approach for RC Square Bridge Columns under Combined Loadings Including Torsion,” Structure Congress, 2012: 2223–2234.
Li Q and Belarbi A (2013), “Damage Assessment of Square RC Bridge Columns Subjected to Torsion Combined with Axial Compression, Flexure, and Shear,” KSCE Journal of Civil Engineering, 17(3): 530–539.
Marin J (1979), “Design Aids for L-Shaped Reinforced Concrete Columns,” ACI Structural Journal, 76(11): 1197–1216.
Li Z, Qin H and Dang H (2008), “Experimental Study on Mechanical Property of Steel Reinforced Concrete L-Shaped Short Columns,” International Journal of Modern Physics B, 22(31n32): 5755–5761.
Liang QQ, Uy B and Liew JYR (2008), “Local Buckling of Steel Plates in Concrete-Filled Thin-Walled Steel Tubular Beam-Columns,” Steel Construction, 63(3): 396–405.
Liu ZQ, Li K and Xue JJ et al. (2018), “Seismic Damage Experiment and Numerical Simulation of Steel Reinforced Concrete T-Shaped Column,” Earthquake Engineering and Engineering Dynamics, 38(5): 85–92. (in Chinese)
Liu ZQ, Li K and Xue JJ et al. (2019), “Experimental Study and Finite Element Analysis on Seismic Behavior of Solid-Web Steel Reinforced Concrete Cross-Shaped and L-Shaped Columns,” Journal of Building Structures, 40(4): 104–115. (in Chinese)
Liu ZQ, Xue JY and Zhao HT (2016), “Seismic Behavior of Steel Reinforced Concrete Special-Shaped Column-Beam Joints,” Earthquakes & Structures, 11(4): 65–680.
Nie JG, Wang YH and Fan JS (2012), “Experimental Study on Seismic Behavior of Concrete Filled Steel Tube Columns Under Pure Torsion and Compression-Torsion Cyclic Load,” Journal of Constructional Steel Research, 79(1): 115–126.
Nie JG, Wang YH and Fan JS (2013), “Experimental Research on Concrete Filled Steel Tube Columns Under Combined Compression-Bending-Torsion Cyclic Load,” Thin-Walled Structures, 67(2): 1–14.
Otuka H, Takeshita E and Urakawa Y (2005), “Seismic Performance and Correlation Characteristics of Reinforced Concrete Columns Subjected to Torsional Moment, Bending Moment/Shear Force and Axial Force,” Doboku Gakkai Ronbunshu, 81: 123–139.
Patton ML and Singh KD (2012), “Numerical Modeling of Lean Duplex Stainless Steel Hollow Columns of Square, L-, T-, And +-Shaped Cross Sections Under Pure Axial Compression,” Thin-Walled Structures, 53: 1–8.
Patton ML and Singh KD (2014), “Finite Element Modelling of Concrete-Filled Lean Duplex Stainless Steel Tubular Stub Columns,” International Journal of Steel Structures, 14(3): 619–632.
Prakash S, Belarbi A and You YM (2010), “Seismic Performance of Circular RC Columns Subjected to Axial Force, Bending, and Torsion with Low and Moderate Shear,” Steel Construction, 32(1): 46–59.
Ramamurthy LN and Khan TAH (1986), “Closure of L-Shaped Column Design for Biaxial Eccentricity,” Journal of Structural Engineering, 112(10): 2360–2362.
Rong B, Feng CX, Zhang RY, et al. (2017), “Compression-bending Performance of L-shaped Column Composed of Concrete Filled Square Steel Tubes under Eccentric Compression,” International Journal of Steel Structures, 17: 325–337.
Rong X, Qiao CN and Yang CH (2018), “Seismic Behavior Test and Finite Element Analysis of Steel Reinforced Concrete Cross-Shaped Columns,” Earthquake Engineering and Engineering Dynamics, 38(2): 63–71. (in Chinese)
Shen ZY, Lei M and Li YQ (2013), “Experimental Study on Seismic Behavior of Concrete-Filled L-Shaped Steel Tube Columns,” Advances in Structural Engineering, 16(7): 1235–1248.
Sun R, Burgess IW and Huang Z (2015), “Progressive Failure Modelling and Ductility Demand of Steel Beam-to-Column Connections in Fire,” Engineering Structures, 89(17): 66–78.
Tirasit P and Kawashima K (2007), “Seismic Performance of Square Reinforced Concrete Columns under Combined Cyclic Flexural and Torsional Loadings,” Journal of Earthquake Engineering.
Teixeira MM and Bernardo LFA (2018), “Ductility of RC Beams Under Torsion,” Engineering Structures, 168: 759–769.
Wang P, Han Q and Du XL (2014), “Seismic Performance of Circular RC Bridge Columns with Flexure-Torsion Interaction,” Soil Dynamics & Earthquake Engineering, 66(66): 13–30.
Wang YH, Wang W and Chen J (2018), “Seismic Behavior of Steel Tube Confined RC Columns Under Compression-Bending-Torsion Combined Load,” Journal of Constructional Steel Research, 143: 83–96.
Weng XH, Shao YJ and Lao YH et al., (2017), “Experimental Study on Seismic Behavior of Steel Reinforced Concrete Column Under Combined Torsion,” Journal of Building Structure, 38(11): 23–33.
Xiao CZ, Deng F and Chen T et al. (2017), “Experimental Study on Concrete-Encased Composite Columns with Separate Steel Sections,” Steel & Composite Structures, 23(4): 483–491.
Xiang P, Deng ZH and Su YS (2017), “Experimental Investigation on Joints Between Steel-Reinforced Concrete T-Shaped Column and Reinforced Concrete Beam Under Bidirectional Low-Cyclic Reversed Loading,” Advances in Structural Engineering, 20(3): 446–460.
Xue JY, Chen ZP and Zhao HT (2012), “Shear Mechanism and Bearing Capacity Calculation on Steel Reinforced Concrete Special-Shaped Columns,” Steel & Composite Structures, 13(5): 473–487.
Xue JY, Zhou CF and Liu ZQ (2017), “Research on Damage of Solid-Web Steel Reinforced Concrete T-Shaped Columns Subjected to Various Loadings,” Steel and Composite Structures, 25(5): 603–615.
Yang Y, Yang H and Zhang S (2010), “Compressive Behavior of T-Shaped Concrete Filled Steel Tubular Columns,” International Journal of Steel Structures, 10(4): 419–430.
Yuan SQ, Chen SC, Tian Y, et al. (2018), “Experimental Study and Analysis of Torsion-Bending Ratio Effect on Aseismic Performance of SRC Columns,” Engineering Mechanics, 35(03): 167–177.
Zhang AL, Yu J and Xu M (2010), “Experiment Research on Steel Specially Columns with Cruciform Section Under Loading,” Journal of Building Structures, 31(2): 11–19.
Zuo ZL, Cai J and Yang C (2012), “Axial Load Behavior of L-Shaped CFT Stub Columns with Binding Bars,” Engineering Structures, 37: 88–98.
Zhou T, Chen Z and Liu H (2012), “Seismic Behavior of Special Shaped Column Composed of Concrete Filled Steel Tubes,” Journal of Constructional Steel Research, 75(75): 131–141.
Acknowledgement
The research reported herein was supported by the National Natural Science Foundation of China (Nos. 51268004 and 51578163), Natural Science Foundation of Guangxi (project No. 2016GXNSFDA380032) and Bagui Scholar Program of Guangxi (No. [2019]79). This financial support is gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Additional information
Supported by: National Natural Science Foundation of China under Grant Nos. 51268004 and 51578163, Natural Science Foundation of Guangxi under Grant No 2016GXNSFDA380032 and Bagui Scholar Program of Guangxi under Grant No: [2019]79
Rights and permissions
About this article
Cite this article
Chen, Z., Ning, F., Chen, J. et al. Test on mechanical behavior of SRC L-shaped columns under combined torsion and bending moment. Earthq. Eng. Eng. Vib. 20, 161–177 (2021). https://doi.org/10.1007/s11803-021-2012-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11803-021-2012-0