Abstract
The selected modifications to the construction of grinding wheels were described which facilitate an increase in the material removal rate (grinding wheels with conic chamfer and grinding wheels with microdiscontinuities on the active surface). Using these background details, a suggested thesis was put forward regarding the need to develop a device which will allow for the shaping of the macrogeometry of the grinding wheel (cylindrical and conical surfaces) and the microdiscontinuities within the dressing operation simultaneously. The device was presented and prepared in two functional variants (horizontal and vertical mounting of the motor), then a prototype was described. An example of the grinding wheel active surface, shaped by using this device, was also presented. The theoretical analysis and experimental verification performed determine that the error of shaping the conic chamfer angle within the range of 0–1.5°, using the developed device, is approximately ±3%.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
MARINESCU I D, HITCHINER M, UHLMANN E, ROWE W B, INASAKI I. Handbook of machining with grinding wheels [M]. Boca Raton: CRC Press, 2007.
ROWE W B. Principles of modern grinding technology [M]. Burlington: William Andrew, 2009.
JACKSON M J, DAVIM J P. Machining with abrasives [M]. New York: Springer, 2010.
KLOCKE F. Manufacturing processes 2: Grinding, honing, lapping [M]. Berlin: Springler-Verlag, 2009.
LÜETJENS P, MUSHARDT H. Grinding out hardened parts [J]. American Mechanist, 2004, 148(3): 52–59.
WEBSTER J, TRICARD M. Innovations in abrasive products for precision grinding [J]. Annals of the CIRP, 2004, 53(2): 597–617.
WEINERT K, FINKE M, KÖTTER D. Wirtschaftliche alternative zum hartdrehen. innenrund-schälschleifen steigert flexibilität beim schleifen von futterteilen [J]. Maschinenmarkt, 2003, 109(48): 44–47.
PLICHTA J, BILL T. Method of grinding wheel dressing using single-grain dresser: Polish, 155182[P]. 1992.
SŁOWIŃSKI B, NADOLNY K. Effective manufacturing method for automated diameter grinding [J]. Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2007, 1(4): 472–480.
NADOLNY K, PLICHTA J. Possibilities of development in the single-pass internal cylindrical grinding [C]// Proceedings of the 19th Int Conference on Systems Engineering. Las Vegas: University of Nevada, 2008: 230–235.
NADOLNY K, SŁOWIŃSKI B. Potential for increasing the effectiveness of automated production systems due to application of single-pass grinding [J]. Advances in Manufacturing Science and Technology, 2010, 34(2): 19–30.
HERMAN D, PLICHTA J, NADOLNY K. Ceramic abrasive tool for single-pass cylindrical grinding and its manufacture: Polish Patent 204902[P]. 2009.
HERMAN D, PLICHTA J, NADOLNY K. New ceramic abrasive tools for rough and finishing grinding in one pass [J]. Materials Science Forum, 2006, 526: 163–168.
PLACKO D. Metrology in industry: The key for quality [R]. London: ISTE Ltd., 2006.
NADOLNY K. Device for shaping of conic chamfer on grinding wheels surface for small angular values: Polish Patent 388765[P]. 2009.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Nadolny, K., Kapłonek, W. Design of a device for precision shaping of grinding wheel macro- and micro-geometry. J. Cent. South Univ. Technol. 19, 135–143 (2012). https://doi.org/10.1007/s11771-012-0982-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11771-012-0982-9