Abstract
Experiments have been performed to investigate the effect of mainstream turbulence on the three-dimensional distribution of the full coverage film cooling effectiveness for two enlarged actual twisted vanes with cylindrical or shaped holes. The film cooling effectiveness was measured by transient liquid crystal technique at mainstream turbulence intensities of 2%, 9% and 15%. The mass flow rate ratios range from 5.5% to 12.5%. There are 3, 8 and 7 rows of film holes on the suction side, leading edge and pressure side, respectively. Results show that for the cylindrical hole vane the high mainstream turbulence intensity decreases the film cooling effectiveness in the top region and down region of pressure side in the low mass flow rate ratio of 5.5%, while the effect is opposite in the high mass flow rate ratio of 12.5%. The film cooling effectiveness in the middle region of pressure side decreases obviously with the increase of the turbulence at the low mass flow rate ratio of 5.5%, while the influence of increasing turbulence weakens gradually with the increase of mass flow rate ratio. Moreover, the high mainstream turbulence improves the film cooling effectiveness in the further downstream of the holes on suction side at the high mass flow rate ratio of 12.5%. For the shaped hole vane, the increase of mainstream turbulence decreases the film cooling effectiveness at all mass flow rate ratios. This study reveals the influence rule of the mainstream turbulence on the film cooling effectiveness in the different regions of the three-dimensional vane surface. The results would guide the designs of engineering heat transfer with application in gas turbine blade/vane cooling.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bunker R.S., Evolution of turbine cooing, ASME Turbo Expo 2017, Charlotte, North Carolina, USA, 2017, paper No. GT2017-63205.
Wieghardt K., Hot-Air discharge for de-icing, AAF Translation (2nd Ed.), Report No. F-TS-919-RE, Wright Field, Ohio, 1946.
Goldstein R.J., Film cooling, Advances in Heat Transfer, 1971, 7: 321–379.
Andrews G.E., Alikhanizadeh M., Tehrani B.F., Hussain C.I., and Azari M.S.K., Small diameter film cooling holes - the influence of hole size and pitch, International Journal of Turbo & Jet Engines, 1988, 5(1–4): 61–72.
Guo S.M., Lai C.C., Jones T.V., Oldfield M.L.G., Lock G.D., Rawlinson A.J., The application of thin-film technology to measure turbine-vane heat transfer and effectiveness in a film-cooled, engine-simulated environment, International Journal of Heat & Fluid Flow, 1998, 19(6): 594–600.
Li G.C., Wang H.F., Zhang W., Kou Z.H., Xu R.S., Film cooling performance of a row of dual-fanned holes at various injection angles, Journal of Thermal Science, 2017, 26(5): 453–458.
Dittmar J., Schulz A., Wittig S., Adiabatic effectiveness and heat transfer coefficient of shaped film cooling holes on a scaled guide vane pressure side model, International Journal of Rotating Machinery, 2014, 10(5): 345–354.
Thole K.A., Sinha A.K., Bogard D.G., Crawford M.E., Mean temperature measurements of jets with a crossflow for gas turbine film cooling application. International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, Honolulu, USA, 1992: 69–85.
Nirmalan V., Hylton L.D., An experimental study of turbine vane heat transfer with leading edge and downstream film cooling, Journal of Turbomachinery, 1990, 112: 477–487.
Han J.C., Dutta S., Ekkad S.V., Gas turbine heat transfer and cooling technology, Taylor and Francis, New York, USA, 2000.
Eriksen V.L., Goldstein R.J., Heat transfer and film cooling following injection through inclined circular tubes, Journal of Heat Transfer, 1974, 96(2): 239–245.
Lebedev V.P., Lemanov V.V., Misyura S.Y., Terekhov V.I., Effects of flow turbulence on film cooling efficiency, International Journal of Heat & Mass Transfer, 1995, 38(11): 2117–2125.
Li G., Chen Y., Kou Z., Zhang W., Zhang G., Mechanism of film cooling with one inlet and double outlet hole injection at various turbulence intensities, International Journal of Turbo & Jet Engines, 2018, 35(1): 1–9.
Schroeder R.P., Thole K.A., Effect of high freestream turbulence on flowfields of shaped film cooling holes, Journal of Turbomachinery, 2016, 138 (9): 091001.
Goldstein R.J., Stone L.D., Row-of-holes film cooling of a convex and a concave wall at low injection angles, Journal of Turbomachinery, 1997, 119(3): 574–579.
James R.W., Joshua B.A., Convex curvature effects on film cooling adiabatic effectiveness. Journal of Turbomachinery, 2013, 136: 061015
Funazaki K.I., Kawabata H., Okita Y., Free-stream turbulence effects on leading edge film cooling, International Journal of Gas Turbine, Propulsion and Power System, 2012, 4(1): 43–50.
Liu J.J., Bai T., et al., Leading edge film cooling enhancement for an inlet guide vane with fan-shaped holes. Journal of Thermal Science, 2010, 19(6): 514–518.
Andrews G.E., Bazdiditehrani F., Small diameter film cooling hole heat transfer - The influence of the number of holes, ASME Gas Turbine and Aeroengine Congress and Expo, Toronto, Canada, 1989, paper No. 89-GT-7.
Abdullah K., Funazaki K.I., Experimental investigations on aero-thermal interaction of film cooling air ejected from multiple shallow angle cooling holes: effect of freestream turbulence, ASME Turbo Expo 2013, San Antonio, Texas, USA, 2013, paper No. GT 2013–95346.
Kingery J., Ames F., Full coverage shaped hole film cooling in an accelerating boundary layer with high free-stream turbulence, Journal of Turbomachinery, 2015, 138 (7): 071002.
Ames F.E., Aspects of vane film cooling with high turbulence: part i—heat transfer. Journal of Turbomachinery, 1998, 120(4): 768–776.
Ames F.E., Aspects of vane film cooling with high turbulence: part ii—adiabatic effectiveness, Journal of Turbomachinery, 1998, 120(4): 777–784.
Cheng L., Zhu H., Jiang R., et al., The effect of turbulence intensity on full coverage film cooling for a turbine guide vane, 2018 Joint Propulsion Conference, Cincinnati, Ohio, 2018, paper No. 2018–4523.
Metzger D.E., Takeuchi D.I., Kuenstler P.A., Effectiveness and heat transfer with full-coverage film cooling, Journal of Engineering for Power, 1973, 95 (3): 180–184.
Gao Z., Narzary D., Mhetras S., Han J.C., Full-coverage film cooling for a turbine blade with axial-shaped holes, Journal of Thermophysics & Heat Transfer, 2012, 22(1): 50–61.
Fu Z.Y., Zhu H.R., Liu C.L., Liu C., Li Z., An experimental investigation of full-coverage film cooling effectiveness and heat transfer coefficient of a turbine guide vane in a linear transonic cascade, ASME Turbo Expo 2016, Soule, South Korea, 2016, paper No. GT2016-56839.
Vedula R.J., Metzger D.E., A method for the simultaneous determination of local effectiveness and heat transfer distributions in three temperature convection situations, ASME Gas Turbine and Aeroengine Congress and Expo 1991, Orlando, FL, USA, 1991, paper No. 91-GT-345.
Drost U., Bolcs A., Hoffs A., Utilization of the transient liquid crystal technique for film cooling effectiveness and heat transfer investigations on a flat plane and a turbine airfoil. ASME Gas Turbine and Aeroengine Congress and Expo 1997, Orlando, FL, USA, 1997, paper No. 97-GT-026.
Shih T.I.P., Chyu M.K., Gogineni S., Yu Y., Yen C.H., Film cooling effectiveness and heat transfer coefficient distributions around diffusion shaped holes, Journal of Heat Transfer, 2002, 124(5): 820–827.
Liu C., Zhu H., Bai J., and Xu D., Film cooling performance of converging-slot holes with different exit-entry area ratios, ASME Turbo Expo 2009, Orlando, FL, USA, 2009, paper No. GT 2009–59002.
Kline S.J., Describing uncertainties in single-sample experiments, Mechanical Engineering, 1953, 75(1): 3–8.
Acknowledgment
The authors acknowledge gratefully the financial support from National Basic Research Program of China (China 973 Program) under number of 2013CB035702.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Fu, Z., Zhu, H., Cheng, L. et al. Experimental Investigation on the Effect of Mainstream Turbulence on Full Coverage Film Cooling Effectiveness for a Turbine Guide Vane. J. Therm. Sci. 28, 145–157 (2019). https://doi.org/10.1007/s11630-019-1085-9
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11630-019-1085-9