Abstract
An approach was presented to characterize the stress response of workpiece in hard machining, accounting for the effect of the initial workpiece hardness in addition to temperature, strain and strain rate on flow stress in this paper. AISI H13 die steel was chosen to verify this methodology. The proposed flow stress model demonstrates a good agreement with experimental data. Therefore, the proposed model can be used to predict the corresponding flow stress-strain response of AISI H13 die steel with variation of the initial workpiece hardness in hard machining.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Axinte D A, Dewes R C. Surface Integrity of Hot Work Tool Steel after High Speed Milling-experimental Data and Empirical Models[J]. J. Mater. Process. Technol., 2002, 127(2): 325–335
Tonshoff H K, Arendt C, Amor R B. Cutting of Hardened Steel[J]. Ann. CIRP, 2000, 49(2): 547–566
Urbanski J P, Koshy P, Dewes R C, et al. High Speed Machining of Moulds and Dies for Net Shape Manufacture[J]. Materials and Design, 2000, 21: 395–402
Yan Hong. Study on Key Technologies of Forming of Magnesium Alloy and High Speed Machining of AISI H13 Die Steel [D]. The Post-Doctoral Research Report at HuaZhong University of Science and Technology, 2004,2 (in Chinese)
Poulachon G, Moisan A, Jawahir I S. On Modelling the Influence of Thermo-mechanical Behavior in Chip Formation during Hard Turning of 100Cr6 Bearing Steel[J]. Ann. CIRP, 2001, 50(1): 31–36
Johnson G R, Cook W H. Fracture Characteristic of Three Metals Subjected to Various Strains, Strain-rate, Temperature and Pressure [J]. Eng. Fract. Mech., 1985, 21: 31–48
Bariani P F, Bruschi S, Negro T D. A New Constitutive Model for Hot Forging of Steels Taking into Account the Thermal and Mechanical History [J]. Annals of the CIRP, 2000, 49(1): 195–198
Jonas J J. Plasticity of Metals at Finite Strain: Theory, Experiment and Computation [J]. Mat. Science and Eng., 1997, 46: 8–13
Huang Zhihong, Lucas, et al. Modeling Wall Boundary Conditions in an Elasto-viscoplastic Material Forming Process[J]. Journal of Materials Processing Technology, 2000, 107(1–3): 267–275
Hu Weilong. Experimental Strain-hardening Behaviors and Associated Computational Models with Anisotropic Sheet Metals[J]. Computational Materials Science, 2000, 18(3–4): 355–361
Shatla M, Kerk C, Altan T. Process Modeling in Machining, Part 1:Determination of Flow Stress Data [J]. Int. J. Mach. Tools Manuf., 2001, 41(10): 1511–1534
Ng E G, Aspinwall D K, Brazil D, et al. Modeling of Temperature and Forces when Orthogonally Machining Hardened Steel [J]. Int. J. Mach. Tools Manuf., 1999, 39(8): 885–903
Ng E G, Aspinwall D K. Modeling of Hard Part Machining [J]. J. Mater. Process. Technol., 2002, 127(2): 222–229
Author information
Authors and Affiliations
Additional information
Funded by the Natural Science Foundation of Jiangxi Province (No. 550067),the National Natural Science Foundation of China(No. 50465003) and Foundation of the State Key Laboratory of Plastic Forming Simulation and Die & Mould Technology (No. 06-3)
Rights and permissions
About this article
Cite this article
Yan, H., Qian, G. & Hu, Q. Development of flow stress of AISI H13 die steel in hard machining. J. Wuhan Univ. Technol. 22, 187–190 (2007). https://doi.org/10.1007/s11595-005-2187-7
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/s11595-005-2187-7