Abstract
A two-dimensional microslip friction model with normal load variation induced by normal motion is presented in this paper. The model is a distributed parameter model, which characterizes the stick-slip-separation of the contact interface and determines the resulting friction force, including its time variance and spatial distribution, between two elastic structures. When the relative motion is simple harmonic motion, the stick-slip-separation transition angles associated with any point in the contact area can be analytically determined within a cycle of motion. In addition, if the relative motion is given, stick-slip-separation transition boundaries inside the contact area and their time variances can be determined. Along with an iterative multi-mode solution approach utilizing harmonic balance method (HBM), the developed model can be employed to determine the forced response of frictionally constrained structures. In the approach, the forced response is constructed in terms of the free mode shapes of the structure; consequently, it can be determined at any excitation frequency and for any type of normal load distribution. Two examples, a one-dimensional beam like damper and a more realistic blade to ground damper, are employed to illustrate the predictive abilities of the developed model. It is shown that while employing a single mode model, transition boundaries for the beam like damper agrees with the results given in the literature, the developed method identifies the phase difference along the slip to stick transition boundary when a multi-mode model is employed. Moreover, while partial slip is illustrated in the two examples, typical softening and hardening effects, due to separation of the contact surface, are also predicted for the blade to ground damper.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Padmanabhan, C. : Analysis of periodically excited systems with clearances. Ph.D. thesis, The Ohio State University (1994)
Yang, B.D.: Contact kinematics of friction interfaces and applications to the prediction of resonant response of frictionally constrained turbine blades Ph.D. thesis, The Ohio State University (1996)
Griffin, J.H.: Friction damping of resonant stresses in gas turbine engine airfoils. J. Eng. Power-Trans. ASME 102, 329–333 (1980)
Dowell, E.H., Schwartz, H.B.: Forced response of a cantilever beam with a dry friction damper attached, part I: Theory. J. Sound Vib. 91, 255–267 (1983)
Cameron, T.M., Griffin, J.H., Kielb, R.E, Hoosac, T.M.: An integrated approach for friction damper design. ASME J. Vib. Acous. Stress Reliab. Design Trans. 112, 175–182 (1990)
Ferri, A.A.: Friction damping and isolation systems. ASME J. Vib. Acoust.-Trans. 117(B), 196–206 (1996)
Menq, C.H., Griffin, J.H., Bielak, J.: The forced response of shrouded fan stages. ASME J. Vib. Acous. Stress Reliab. Design Trans. 108, 50–55 (1986)
Yang B.D., Menq C.H.: Characterization of contact kinematics and application to the design of wedge dampers in turbomachinery blading: part I: stick-slip contact kinematics. J. Eng. Gas Turbines Power Trans. ASME 120(2), 410–417 (1998)
Menq, C.H., Griffin, J.H., Bielak, J.: The influence of a variable normal load on the forced vibration of a frictionally damped structure. J. Eng. Gas Turbines Power 108, 300–305 (1986)
Yang, B.D., Chu, M.L., Menq, C.H.: Stick-slip-separation analysis and non-linear stiffness and damping characterization of friction contacts having variable normal load. J. Sound Vib. 210, 461–481 (1998)
Yang, B.D., Menq, C.H.: Characterization of 3D contact kinematics and prediction of resonant response of structures having 3D frictional constraint. J. Sound Vib. 217, 909–925 (1998)
Chen, J.J., Menq, C.H.: Periodic response of blades having three-dimensional nonlinear shroud constraints. J. Eng. Gas Turbines Power 123, 901–909 (2001)
Petrov, E.P., Ewins, D.J.: Analytical formulation of friction interface elements for analysis of nonlinear multi-harmonic vibrations of bladed disks. J. Turbomach. 125, 364–371 (2003)
Menq, C.H., Bielak, J., Griffin, J.H.: The influence of microslip on vibratory response, Part I A new microslip model. J. Sound Vib. 107, 279–293 (1986)
Menq, C.H., Bielak, J., Griffin, J.H.: The influence of microslip on vibratory response, Part II A comparison with experimental results. J. Sound Vib. 107, 295–307 (1986)
Csaba, G.: Forced response analysis in time and frequency domains of a tuned bladed disk with friction dampers. J. Sound Vib. 214, 395–412 (1998)
Quinn, D.D., Segalman, D.J.: Using series-series Iwan-type models for understanding joint dynamics. J. Appl. Mech. 72, 666–673 (2005)
Cigeroglu, E., Lu, W., Menq, C.H.: One-dimensional dynamic microslip friction model. J. Sound Vib. 292, 881–898 (2006)
Filippi, S., Akay, A., Gola, M.M.: Measurement of tangential contact hysteresis during microslip. J. Tribol. 126, 482–489 (2004)
Koh, K-H., Filippi, S., Griffin, J.H., Akay, A.: Characterization of turbine blade friction dampers. J. Eng. Gas Turbines Power 127, 856–862 (2005)
Menq, C.H., Griffin, J.H.: A comparison of transient and steady state finite element analyses of the forced response of a frictionally damped beam. J. Vib. Acoust. Stress Reliab. Des. 107, 19–25 (1985)
Tanri kulu, Ö., Kuran, B., Özgüven, H.N., Imregün, M.: Forced harmonic response analysis of nonlinear structures using describing functions. AIAA J. 31, 1313–1320 (1993)
Sanliturk, K.Y., Ewins, D.J., Elliott, R., Green, J.S.: Friction damper optimization: simulation of rainbow tests. J. Eng. Gas Turbines Power 123, 930–939 (2001)
Ciugerouglu, E., Özgüven, H.N.: Nonlinear vibration analysis of bladed disks with dry friction dampers. J. Sound Vib. 295, 1028–1043 (2006)
Yang, M.T., Griffin, J.H.: A reduced order approach for the vibration of mistuned bladed disk assemblies. J. Eng. Gas Turbines Power 119, 161–167 (1997)
Bladh, R., Castanier, M.P., Pierre, C.: Component-mode-based reduced order modeling techniques for mistuned bladed disks-part I: theoretical models. J. Eng. Gas Turbines Power 123, 89–99 (2001)
Bladh, R., Castanier, M.P., Pierre, C.: Component-mode-based reduced order modeling techniques for mistuned bladed disks-part I: application. J. Eng. Gas Turbines Power 123, 100–108 (2001)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Cigeroglu, E., An, N. & Menq, CH. A microslip friction model with normal load variation induced by normal motion. Nonlinear Dyn 50, 609–626 (2007). https://doi.org/10.1007/s11071-006-9171-4
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11071-006-9171-4