Abstract
Specimens of steel 70 are studied before and after alkaline galvanizing and after galvanizing and partial dehydrogenizing. The content of hydrogen and its distribution between the coating and the substrate are estimated. The structures of the substrate metal and of the coating are studied before and after dehydrogenization. Mechanical tests at various rates of deformation of specimens of steel 70 in different initial states are performed. The tests are followed by an analysis of fracture surfaces. The effect of hydrogen on the fracture behavior is evaluated at different rates of deformation of specimens. The effect of reversibility of the structure and properties in “hydrogen charging-dehydrogenization” of the steel is determined and the mechanism of formation of a layered structure of zinc coatings is described.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
O. I. Steklov, N. G. Borodin, V. M. Kushnarenko, and B. V. Perunov, Tests of Steels and Welded Joints in Hydrogen-Charging Media [in Russian], Metallurgiya, Moscow (1992).
Yu. I. Archakov, Hydrogen Corrosion of Steel [in Russian], Metallurgiya, Moscow (1985).
B. A. Kolachev, Hydrogen Brittleness of Metals [in Russian], Metallurgiya, Moscow (1985).
V. V. Kuznetsov, G. V. Khaldeev, and V. I. Kichigin, Hydrogen Charging of Metals [in Russian], Mashinostroenie, Moscow (1993).
G. M. Pressouyre, Current Solutions to Hydrogen Problem in Steels, American Society for Materials International, Materials Park (1982).
V. I. Shapovalov, Effect of Hydrogen on the Structure and Properties of Iron-Carbon Alloys [in Russian], Metallurgiya, Moscow (1982).
Y. Z. Liu, X. T. Zu, C. Li, et al., “Hydrogen embrittlement of a Ti-Al-Zr alloy evaluated by impact test method,” Scr. Mater., 52(9), 821–825 (2005).
L. Yang and R. B. McLellan, “Effect of palladium on the hydrogen embrittlement of B-doped Ni3Al,” J. Mater. Res., 11(4), 862 (1997).
D. A. Berman, “The effect of baking and stress on the hydrogen content of cadmium plated high strength steels,” Mater. Perform., 24, 36–41 (1985).
P. V. Geld, R. A. Ryabov, and E. S. Kodes, Hydrogen and Imperfections in the Structure of Metal [in Russian], Metallurgiya, Moscow (1979).
M. A. Shtremel’, The Strength of Alloys, Part II, Deformation [in Russian], MISiS, Moscow (1997).
V. K. Nosov and B. A. Kolachev, Hydrogen Plasticizing in Hot Deformation of Titanium Alloys [in Russian], Metallurgiya, Moscow (1986).
A.-M. Brass and J. Chêne, “Hydrogen uptake in 3161 stainless steel: consequences on the tensile properties,” Corrosion Sci., 48, 3222–3242 (2006).
V. M. Chertov, “Galvanizing: a cause of hydrogen embrittlement of high-strength steel,” Altern. Energ. Ekolog., 7(27), 28–31 (2005).
Yu. D. Gamburg, Electrodeposited Coatings: An Application Guide [in Russian], Tekhnosphera, Moscow (2006).
V. P. Maksimchuk and S. P. Polovnikov, Hydrogen Cracking of High-Strength Steels after Electrochemical Deposition of Coatings [in Russian], Énergoatomizdat, Moscow (2002).
N. K. Meshkov and V. I. Kholodnyi, “Materials and metallurgical processes for power installations on cryogenic components,” Altern. Energ. Ekol., 2(10), 41–47 (2004).
E. V. Proskurin, V. A. Popovich, and A. T. Moroz, Galvanizing, A Reference Book [in Russian], Metallurgiya, Moscow (1988).
Author information
Authors and Affiliations
Additional information
__________
Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 10, pp. 36–42, October, 2007.
Rights and permissions
About this article
Cite this article
Krishtal, M.M., Yasnikov, I.S., Eremichev, A.A. et al. Effect of reversibility of structure and properties in hydrogen charging of carbon steel and influence of hydrogen on formation of electrodeposited zinc coatings. Met Sci Heat Treat 49, 490–496 (2007). https://doi.org/10.1007/s11041-007-0091-9
Issue Date:
DOI: https://doi.org/10.1007/s11041-007-0091-9