Abstract
Based on the superiority of self-developed cermet micro-mill over commercial cemented tungsten micro-mill in our previous work, the cutting characteristics, machined channel quality, and tool wear were investigated in this work, aiming at the evaluation of tool performance of this cermet micro-mill during micro-milling aluminum alloy 2024. Burrs and dimensional accuracy of machined channels, tool wear, and chip morphology were analyzed at various cutting parameters. The machining and forming mechanism related with cermet micro-mill were thoroughly discussed. It indicated that the cutting conditions can be optimized to enhance the performance of cermet micro-mills. The optimum cutting parameter can produce not only the good quality and high dimensional accuracy of channel with few small burrs but also the tool wear to a small degree ever after micro-milling of 10–20 min. The cermet micro-mill also exhibited the good capacity to break the chip. The good performance of cermet micro-mill was attributed to its good chemical stability and high hardness, especially the gained sharper tool tips and edges, and their better stability.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Davim JP (2014) Modern mechanical engineering. Springer, London
Gupta MC, Li B, Gadag S, Chou KC (2010) Laser micromachining for fatigue and fracture mechanics applications. Opt Lasers Eng 48:441–447
Jan AC, Reichenbach IG, Schuler GM (2012) Manufacture and application of ultra-small micro end mills. CIRP Ann-Manuf Technol 61:83–86
Zhan ZB, He N, Li L, Shrestha R, Liu JY, Wang SL (2015) Precision milling of tungsten carbide with micro PCD milling tool. Int J Adv Manuf Technol 77:2095–2103
Suzuki H, Okada M, Fujii K, Matsui S, Yamagata Y (2013) Development of micro milling tool made of single crystalline diamond for ceramic cutting. CIRP Ann Manuf Technol 62:59–62
Cheng X, Wang ZG, Nakamoto K, Yamazaki K (2010) Design and development of PCD micro straight edge end mills for micro/nano machining of hard and brittle materials. J Mech Sci Tech 24:2261–2268
Cheng X, Wang Z, Nakamoto K, Yamazaki K (2011) A study on the micro tooling for micro/nano milling. Int J Adv Manuf Technol 53:523–533
Egashira K, Hosono S, Takemoto S, Masao Y (2011) Fabrication and cutting performance of cemented tungsten carbide micro-cutting tools. Precis Eng 35:547–553
Aurich JC, Reichenbach IG, Schüler GM (2012) Manufacture and application of ultra-small micro end mills. CIRP Ann-Manuf Technol 61:83–86
Cuba AR, Autenrieth H, Strau T, Deuchert M, Hoffmeister J (2012) Characterization of the transition from ploughing to cutting in micro machining and evaluation of the minimum itchiness of cut. J Mater Process Technol 212:594–600
Fernanado DO, Alessandro RR, Reginaldo TC, Adriano FS (2015) Size effect and minimum chip thickness in micromilling. Int J Mach Tools Manuf 89:39–54
Annoni M, Biella G, Rebaioli L, Semeraro Q (2013) Microcutting force prediction by means of a slip-line field force model. Procedia CIRP 8:558–563
Mamedov A, Lazoglu I (2016) An evaluation of micro milling chip thickness models for the process mechanics. Int J Adv Manuf Technol 87:1843–1849
Nakamoto K, Katahira K, Ohmori H, Yamazaki K, Aoyama TY (2012) A study on the quality of micro-machined surfaces on tungsten carbide generated by PCD micro end-milling. CIRP Ann-Manuf Technol 61:567–570
Ucun I, Aslantas K, Bedir F (2013) An experimental investigation of the effect coating material on tool wear in micro milling of Inconel 718 super alloy. Wear 300:8–19
Kiswanto G, Zariatin DL, Ko TJ (2014) The effect of spindle speed, feed-rate and machining time to the surface roughness and burr formation of aluminium alloy 1100 in micro-milling operation. J Manuf Process 16:435–450
Kuram E, Ozcelik B (2013) Multi-objective optimization using Taguchi based grey relational analysis for micro-milling of Al 7075 material with ball nose end mill. Measurement 46:1849–1864
Zou B, Zhou HJ, Xu KT, Huang CZ, Wang J, Li SS (2014) Study of a hot-pressed sintering preparation of Ti(C7N3)-based composite cermets materials and their performance as cutting tools. J Alloy Compd 611:363–371
Xu KT, Zou B, Wang YS, Guo P, Huang CZ, Wang J (2016) An experimental investigation of micro-machinability of aluminium alloy 2024 using Ti(C7N3)-based cermet micro end-mill tools. J Mater Process Technol 235:13–17
Park SS, Malekian M (2009) Mechanistic modeling and accurate measurement of micro end milling forces. CIRP Ann-Manuf Technol 58:49–52
Filiz S, Conley MC, Wasserman MB, Ozdoganlar OB (2007) An experimental investigation of micro-machinability of copper 101 using tungsten carbide micro-endmills. Int J Mach Tools Manuf 47:1008–1100
Li P, Zdebski D, Langen HH, Hoogstrate AM (2011) Micromilling of thin ribs with high aspect ratios. J Micromech Microeng 20:13–23
Mamedov A, Lazoglu I (2016) An evaluation of micro milling chip thickness models for the process mechanics. Int J Adv Manuf Technol 87:1843–1849
Rezaei H, Sadeghi MH, Budak E (2018) Determination of minimum uncut chip thickness under various machining conditions during micro-milling of Ti-6Al-4V. Int J Adv Manuf Technol 95:1617–1634
Sooraj V, Mathew J (2011) An experimental investigation on the machining characteristics of microscale end milling. Int J Adv Manu Technol 56:951–958
Acknowledgments
This project was supported by Shandong Science Fund for Distinguished Young Scholars (JQ201715) and the National Natural Science Foundation of China (no. 51575322).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Li, S., Zou, B., Xu, K. et al. Machined channel quality and tool life using cermet micro-mill in micro-milling aluminum alloy. Int J Adv Manuf Technol 101, 2205–2216 (2019). https://doi.org/10.1007/s00170-018-3120-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-3120-5