Abstract
The applications of functional ceramics are significantly limited by the brittleness and low reliability. Recent studies have shown that compressive residual stress can be created in ceramics by shot peening, which improves the contact strength and fatigue of ceramic components. However, the formation mechanism of residuals stress in shot peening is yet to understand. In this study, a pressure-dependent plasticity model has been incorporated into a finite element simulation model of shot peening to understand the process mechanism underpinning the residual stress formation. Since shot velocity is the key process parameter to dominate the impact energy which determines the deformation state of the peened surface and the resultant residual stress, a new kinematic model of shots has also been developed by incorporating air drag and travel distance inside and outside the peening nozzle. The results have shown that the shot velocity model can be used to predict shot velocity. The experiment-based model may help understand the process mechanism underpinning the residual stress formation.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ferraris E, Vleugels J, Guo YB, Bourell D, Kruth JP, Lauwers B (2016) Shaping of engineering ceramics by electro, chemical and physical processes. CIRP Ann Manuf Technol 65(2):761–784
Pfeiffer W, Frey T (2002) Shot peening of ceramics: damage or benefit? CFI-Ceramic Forum Int 79(4):E25–E28
Moon W, Ito T, Uchimura S, Saka H (2004) Toughening of ceramics by dislocation sub-boundaries. Mat Sci Eng A-Struct 387–389:837–839
Tomaszewski H, Godwod K, Diduszko R, Carrois F, Duchazeaubeneix J (2006) Shot peening—a new method for improving mechanical properties of structural ceramics. Key Eng Mater 317:277–280
Pfeiffer W, Frey T (2006) Strengthening of ceramics by shot peening. J Eur Ceram Soc 26(13):2639–2645
Takahashi K, Nishio Y (2012) Improvement of the contact strength of Si3N4/SiC by a combination of shot peening and crack-healing. JSME Int J Ser A 6(2):144–153
Tanaka K, Akiniwa Y, Morishita Y (2005) Residual stress distribution in the sub-surface region of shot-peened ceramics. Transe Jpn Soc Mech Eng 71:1714–1721
Takahashi K, Nishio Y, Kimura Y, Ando K (2010) Improvement of strength and reliability of ceramics by shot peening and crack healing. J Eur Ceram Soc 30(15):3047–3052
Kirk D (2007) Generation of air-blast shot velocity. Shot Peener 21(1):24–30
Li HZ, Wang J, Fan JM (2009) Analysis and modelling of particle velocities in micro-abrasive air jet. Int J Mach Tool Manu 49(11):850–858
Almen J, Black JPH (1963) Residual stresses and fatigue in metals. McGraw-Hill
Miao HY, Larose S, Perron C, Lévesque M (2010) An analytical approach to relate shot peening parameters to Almen intensity. Surf Coat Tech 205(7):2055–2066
Al-Obaid YF (1990) Three-dimensional dynamic finite element analysis for shot-peening mechanics. Comput Struct 36(4):681–689
Meguid S, Shagal G, Stranart J (2007) Development and validation of novel FE models for 3D analysis of peening of strain-rate sensitive materials. J Eng Mater-T ASME 129(2):271–283
Kim T, Lee H, Kim M, Jung S (2012) A 3D FE model for evaluation of peening residual stress under angled multi-shot impacts. Surf Coat Tech 206(19–20):3981–3988
Hong T, Ooi JY, Shaw BA (2008) A numerical study of the residual stress pattern from single shot impacting on a metallic component. Adv Eng Softw 39(9):743–756
Miao HY, Larose S, Perron C, Lévesque M (2009) On the potential applications of a 3D random finite element model for the simulation of shot peening. Adv Eng Softw 40(10):1023–1038
Frija M, Hassine T, Fathallah R, Bouraoui C, Dogui A (2006) Finite element modelling of shot peening process: prediction of the compressive residual stresses, the plastic deformations and the surface integrity. Mat Sci Eng A-Struct 426(1–2):173–180
Bagherifard S, Ghelichi R, Guagliano M (2012) Numerical and experimental analysis of surface roughness generated by shot peening. Appl Surf Sci 258(18):6831–6840
Gangaraj SMH, Guagliano M, Farrahi GH (2014) An approach to relate shot peening finite element simulation to the actual coverage. Surf Coat Tech 243:39–45
Thomas PJ (1999) Simulation of industrial processes for control engineers. Butterworth-Heinemann
Momber A (2008) Blast cleaning technology. Springer
Rajaratnam N (1976) Turbulent Jets. Elsevier
Johnson GR, Holmquist TJ (1994) An improved computational constitutive model for brittle materials. High-pressure science and technology, Colorado Springs, CO, USA, AIP Conference Proceedings
Anderson C, Johnson G, Holmquist T (1995) Ballistic experiments and computations of confined 99.5% Al2O3 ceramic tiles. Proceedings of the 15th International Symposium on Ballistics, Israel, Jerusalem.
Guo YB, Sealy MP, Guo C (2012) Significant Improvement of corrosion resistance of biodegradable metallic implants processed by laser shock peening. CIRP Ann Manuf Technol 61(1):583–586
Deshpande VS, Gamble EAN, Compton BG, McMeeking RM, Evans AG, Zok FW (2011) A constitutive description of the inelastic response of ceramics. J Am Ceram Soc 94:s204–s214
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Liu, Z.Y., Huang, C., Zhao, Y. et al. Kinematic modeling and deformation mechanics in shot peening of functional ceramics. Int J Adv Manuf Technol 93, 1669–1683 (2017). https://doi.org/10.1007/s00170-017-0661-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0661-y