Abstract
To achieve cost-effective patterning of microfeatures on the nonplanar surfaces, a modified through-mask electrochemical micromachining process (TMEMM) was developed in which a layer of flexible insulating media with interconnected micropores is filled in the interelectrode gap and presses the through mask, considerably facilitating the mechanically attachment of the reusable through mask to the complex workpieces during EMM. A uniquely special tool cathode with a variety of outlet passages was correspondingly designed to significantly alleviate mass transfer limitation because of introduction of the flexible media. Some numerical and experimental investigations were then carried out to evaluate this proposed TMEMM process, with the focus on analyzing the dimension distribution uniformity of the machined microdimples. It is showed that the modified active TMEMM process exhibits favorable machinability and applicability to produce microdimples with significantly uniform geometric profiles on the planar and nonplanar surfaces.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
West AC, Madore C, Matlosz M, Landolt D (1992) Shape changes during through-mask electrochemical micromachining of thin metal films. J Electrochem Soc 139(2):499–506
Shenoy RV, Datta M, Romankiw LT (1996) Investigation of island formation during. through-mask electrochemical micromachining. J Electrochem Soc 143(7):2305–2309
Datta M (1998) Microfabrication by electrochemical metal removal. IBM J Res Dev 42(5):655–670
Datta M, Landolt D (2000) Fundamental aspects and applications of electrochemical microfabrication. Electrochim Acta 45(15):2535–2558
McCrabb H, Lozano-Morales A, Snyder S (2009) Through mask electrochemical machining. ECS Trans 19(26):19–33
Zhu D, Qu NS, Li HS et al Electrochemical micromachining of microstructures of micro hole and dimple array. CIRP Ann Manuf Technol 58(1):177–180
Qian SQ, Zhu D, Qu NS (2010) Generating micro-dimples array on the hard chrome-coated surface by modified through mask electrochemical micromachining. Inter J Adv Manuf Technol 47(9–12):1121–1127
Chen XL, Qu NS, Li HS, Xue ZX (2015) Pulsed electrochemical micromachining for generating micro-dimple arrays on a cylindrical surface with a flexible mask. Appl Surf Sci 343:141–147
Chauvy PF, Madore C, Landolt D (1999) Electrochemical micromachining of titanium through a patterned oxide film. Electrochem Solid-state Lett 2(3):123–125
Chauvy PF, Hoffmann P, Landolt D (2001) Electrochemical micromachining of titanium through a laser patterned oxide film. Electrochem Solid-State Lett 4(5):C31–C34
Chauvy PF, Hoffmann P, Landolt D (2003) Applications of laser lithography on oxide film to titanium micromachining. ApplSurf Sci 208:165–170
Schönenberger I, Roy S (2005) Microscale pattern transfer without photolithography of substrates. Electrochim Acta 51(5):809–819
Costa HL, Hutchings IM (2009) Development of a maskless electrochemical texturing method. J Mater Process Technol 209:3869–3878
Parreira JG, Gallo CA, Costa HL (2012) New advances on maskless electrochemical texturing (MECT) for tribological purposes. Surf Coat Technol 212:1–13
Zhu D, Qu NS, Li HS (2009) Electrochemical micromachining of microstructures of micro hole and dimple array. CIRP Ann Manuf Technol 58:177–180
Li DL, Zhu D, Li HS (2011) Effects of mask wall angle on matrix-hole shape changes during electrochemical machining by mask. J Cent South Uni Tech 18:1115–1120
Li DL, Zhu D, Li HS (2011) Microstructure of electrochemical micromachining using inert metal mask. Int J Adv Manuf Technol 55:189–194
Qu NS, Chen XL, Li HS, Zeng YB (2014) Electrochemical micromachining of micro-dimple arrays on cylindrical inner surfaces using a dry-film photoresist. Chin J Aeronaut 27:612–618
Zhang X, Qu NS, Li HS (2015) Investigation of machining accuracy of micro-dimples fabricated by modified microscale pattern transfer without photolithography of substrates. Int J Adv Manuf Techno 81(9–12):1475–1485
Qu NS, Zhang XF, Chen XL (2015) Modified microscale pattern transfer without photolithography of substrates. J Mater Process Technol 218:71–79
Chen XL, Qu NS, Li HS (2014) The fabrication and application of a PDMS micro through-holes mask in electrochemical micromanufacturing. Adv Mech Eng 6:1–7
Chen XL, Qu NS, Li HS (2015) Removal of islands from micro-dimple arrays prepared by through-mask electrochemical micromachining. Precis Eng 39:204–211
Chen XL, Qu NS, Li HS (2016) Electrochemical micromachining of micro-dimple arrays using a polydimethylsiloxane (PDMS) mask. J Mat Process Technol 229:102–110
Chen XL, Qu NS, Li HS (2015) Pulsed electrochemical micromachining for generating micro-dimple arrays on a cylindrical surface with a flexible mask. Appl Surf Sci 343:141–147
Li DL. Application and fundamental research of multiple holes by electrochemical machining using mask. Nanjing: Nanjing University of Aeronautics and Astronautics (in Chinese)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ming, P., Zhou, W., Zhao, C. et al. Development of a modified through-mask electrochemical micromachining for micropatterning nonplanar surface. Int J Adv Manuf Technol 93, 2613–2623 (2017). https://doi.org/10.1007/s00170-017-0541-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0541-5