Abstract
To allow very high turbine inlet gas temperatures, film cooling holes are widely applied in gas turbine engines. Owing to the requirements of high machining efficiency and surface quality, the fabrication of film cooling holes in difficult-to-machine materials is extremely difficult. A tubular electrode electro-discharge high-speed drilling/electrochemical machining (ECM) in situ combined process has been proposed for this task. In this approach, electro-discharge machining (EDM) is efficiently employed to form the holes, following which the recast layer thereby generated is removed from the machined surface by electrochemical dissolution. In this study, a tubular electrode and a specially designed flushing device are used, with internal and side flushing being performed at the same time so that EDM and ECM can be combined in situ. The performance of the technique is investigated on a nickel-based superalloy. To achieve the best performance, the ideal values of EDM parameters (peak current, pulse duration, and pulse interval) are determined. The ECM is employed to remove the rough surface produced by the EDM. Compared with EDM alone, it is found that the EDM/ECM in situ combined process improves the surface quality of the holes and removes the recast layer. It is confirmed that the combined process is suitable for producing film cooling holes without a recast layer.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Bilgi DS, Jain VK, Shekhar R, Mehrotra S (2004) Electrochemical deep hole drilling in super alloy for turbine application. J Mater Process Technol 149(1–3):445–452
Liu K, Yang SF, Han JC (2014) Influence of coolant density on turbine blade film-cooling with axial and compound shaped holes. J Heat Trans-T ASME 136(4):1–5
Fang XL, Qu NS, Li HS, Zhu D (2013) Enhancement of insulation coating durability in electrochemical drilling. Int J Adv Manuf Technol 68(9–12):2005–2013
Ferraris E, Castiglioni V, Ceyssens F, Annoni M, Lauwers B, Reynaerts D (2013) EDM drilling of ultra-high aspect ratio micro holes with insulated tools. Ann CIRP 62(1):191–194
Liu K, Lauwers B, Reynaerts D (2010) Process capabilities of micro-EDM and its applications. Int J Adv Manuf Technol 47(1–4):11–19
Li JZ, Shen FH, Yu ZY, Natsu W (2013) Influence of microstructure of alloy on the machining performance of micro EDM. Surf Coat Tech 228(1):460–465
Nikalje AM, Kumar A, Srinadh KVS (2013) Influence of parameters and optimization of EDM performance measures on MDN 300 steel using Taguchi method. Int J Adv Manuf Technol 69(1–4):41–49
D’Urso G, Maccarini G, Ravasio C (2014) Process performance of micro-EDM drilling of stainless steel. Int J Adv Manuf Technol 72(9–12):1287–1298
Hao Ning C, Wang JJJ (2011) An analysis of overcut variation and coupling effects of dimensional variable in EDM process. Int J Adv Manuf Technol 55(9–12):935–943
Nguyen MD, Rahman M, San Wong Y (2012) An experimental study on micro-EDM in low-resistivity deionized water using short voltage pulses. Int J Adv Manuf Technol 58(5–8):533–544
Wang CC, Chow HM, Yang LD, Lu CT (2009) Recast layer removal after electrical discharge machining via Taguchi analysis: a feasibility study. J Mater Process Technol 209(8):4134–4140
Amineh SK, Tehrani AF, Mohammadi A (2013) Improving the surface quality in wire electrical discharge machined specimens by removing the recast layer using magnetic abrasive finishing method. Int J Adv Manuf Technol 66(9–12):1793–1803
Cusanelli G, Hessler-Wyser A, Bobard F, Demellayer R, Perez R, Flükiger R (2004) Microstructure at submicron scale of the white layer produced by EDM technique. J Mater Process Technol 149(1):289–295
Lee HT, Tai TY (2003) Relationship between EDM parameters and surface crack formation. J Mater Process Technol 142(3):676–683
McGeough JA, Khayry ABM, Munro W, Crookall JR (1983) Theoretical and experimental investigation of the relative effects of spark erosion and electrochemical dissolution in electrochemical arc machining. Ann CIRP 32(1):113–118
Kurita T, Hattori M (2006) A study of EDM and ECM/ECM-lapping complex machining technology. Int J Mach Tool Manuf 46(14):1804–1810
Chung DK, Shin HS, Kim BH, Park MS, Chu CN (2009) Surface finishing of micro-EDM holes using deionized water. J Micromech Microeng 19(4):1–7
Ramasawmy H, Blunt L, Rajurkar K (2005) Investigation of the relationship between the white layer thickness and 3D surface texture parameters in the die sinking EDM process. Precis Eng 29(4):479–490
Zeng Z, Wang Y, Wang Z, Shan D, He X (2012) A study of micro-EDM and micro-ECM combined milling for 3D metallic micro-structures. Precis Eng 36(3):500–509
Klocke F, Klink A, Veselovac D, Aspinwall DK, Soo SL, Schmidt M, Schilp J, Levy G, Kruth J-P (2014) Turbomachinery component manufacture by application of electrochemical, electro-physical and photonic processes. Ann CIRP 63(2):703–726
Thanigaivelan R, Arunachalam RM, Drukpa P (2012) Drilling of micro-holes on copper using electrochemical micromachining. Int J Adv Manuf Technol 61(9–12):1185–1190
Zhu D, Wang W, Fang X, Qu N, Xu Z (2010) Electrochemical drilling of multiple holes with electrolyte-extraction. Ann CIRP 59(1):239–242
Ramasawmy H, Blunt L (2007) Investigation of the effect of electrochemical polishing on EDM surfaces. Int J Adv Manuf Technol 31(11–12):1135–1147
Lauwers B, Klocke F, Klink A, Tekkaya AE, Neugebauer R, McIntosh D (2014) Hybrid processes in manufacturing. Ann CIRP 63(2):561–583
Skoczypiec S, Ruszaj A (2014) A sequential electrochemical-electrodischarge process for micropart manufacturing. Precis Eng 38(3):680–690
Nguyen MD, Rahman M, Wong YS (2012) Simultaneous micro-EDM and micro-ECM in low-resistivity deionized water. Int J Mach Tool Manuf 54:55–65
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, Y., Xu, Z., Zhu, D. et al. Drilling of film cooling holes by a EDM/ECM in situ combined process using internal and side flushing of tubular electrode. Int J Adv Manuf Technol 83, 505–517 (2016). https://doi.org/10.1007/s00170-015-7575-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-015-7575-3