Abstract
The objective of this research is to evaluate and optimize machining parameter of tool electrode vibration on micro-electric discharge machining of polycrystalline diamond. The machining parameters evaluated are charge voltage, capacitance, and vibration of the tool electrode. An orthogonal array, signal-to-noise ratio, and analysis of variance are employed to analyze the effect of these machining parameters. The results show that by application of vibration on tool electrode in machining of polycrystalline diamond, it has significant effect up to 66.48% in increasing material removal rate without increasing surface roughness and tool electrode wear. Using Taguchi method for design of experiment, other significant effects on surface quality and tool electrode wear are also investigated. The results also show that surface roughness is mostly affected by the amount of capacitance (52.24%), and the tool electrode wear is also affected by the amount of capacitance (92.82%).
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Mahardika M, Tsujimoto T, Mitsui K (2008) A new approach on the determination of ease of machining by EDM processes. Int J Mach Tool Manuf 48:746–760
Abbas NM, Solomon DG, Bahari MF (2007) A review on current research trends in electrical discharge machining (EDM). Int J Mach Tool Manuf 47:1214–1228
Prihandana GS, Mahardika M, Hamdi M, Wong YS, Mitsui K (2009) Effect of micro-powder suspension and ultrasonic vibration of dielectric fluid in micro-EDM processes—Taguchi approach. Int J Mach Tool Manuf 49:1035–1041
Davim JP, Maranhao C, Jackson MJ et al (2008) FEM analysis in high speed machining of aluminium alloy (Al7075-0) using polycrystalline diamond (PCD) and cemented carbide (K10) cutting tools. Int J Adv Manuf Technol 39:1093–1100
Muthukrishnan N, Murugan M, Rao KP (2008) An investigation on the machinability of Al-SiC metal matrix composites using PCD inserts. Int J Adv Manuf Technol 38:447–454
Tso PL (2002) Study on PCD machining. Int J Mach Tool Manuf 42:331–334
Cassidy R (2000) PCD grinding optimization. INTERTECH 2000, Staffordshire, United Kingdom
Cheng X, Wang ZG, Kobayashi S, Nakamoto K, Yamazaki K (2008) Development of a six-axis wire electrical discharge machine for the fabrication of micro end mills. Proc IMechE Part B: J Engineering Manufacture 223:121–131
Palanikumar K (2008) Application of Taguchi and response surface methodologies for surface roughness in machining glass fiber reinforced plastics by PCD tooling. Int J Adv Manuf Technol 36:19–27
Ross PJ (1989) Taguchi techniques for quality engineering. McGraw-Hill, New York
Wu FC, Chyu CC (2002) A comparative study on Taguchi’s SN ratio, minimising MSD and variance for nominal-the-best characteristic experiment. Int J Adv Manuf Technol 20:655–659
Mahardika M, Mitsui K (2008) A new method for monitoring micro-electric discharge machining processes. Int J Mach Tool Manuf 48:446–458
Endo T, Tsujimoto T, Mitsui K (2008) Study of vibration-assisted micro-EDM—the effect of vibration on machining time and stability of discharge. Precis Eng 32:269–277
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mahardika, M., Prihandana, G.S., Endo, T. et al. The parameters evaluation and optimization of polycrystalline diamond micro-electrodischarge machining assisted by electrode tool vibration. Int J Adv Manuf Technol 60, 985–993 (2012). https://doi.org/10.1007/s00170-011-3674-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-011-3674-y