Abstract
Micro injection molding presents many challenges in the injection-molding community. When the dimensions of the part (and thus the cavity of the mold) are small, micro-scale factors such as mold surface roughness may play an important role in the filling of polymer melt. This paper investigates the effects of mold surface roughness on cavity filling of polymer melt in micro injection molding. A disk insert, which has two halves with different surface roughness but with the same roughness mean lines, was used in the investigations. The ratio of flow area of the rougher half with the total flow area of the molded part is used to evaluate the significance of surface roughness effect. The experimental results revealed that mold surface roughness does resist the cavity filling of polymer melt in micro injection molding. For the limited range of injection rate investigated, it is not significant on the surface roughness effects. The increase of mold temperature will decrease surface roughness effects. The change of melt temperature within the range allowed by the process is insignificant for surface roughness effects.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Yu LY, Koh CG, Lee LJ, Koelling DW (2002) Experimental investigation and numerical simulation of injection molding with micro-features. Int Comm Heat Mass Transfer 42(5):871–888
Zhao J, Mayes RH, Chen G, Xie H, Chan PS (2003) Effects of process parameters on the micro molding process. Polymer Eng Sci 43(9):1542–1554
Shen YK, Wu WY (2002) An analysis of the three-dimensional micro-injection molding. Int Comm Heat Mass Transfer 29(3):423–431
Ong NS, Koh YH (2005) Experimental investigation into micro injection molding of plastic parts. Mater Manuf Process 20:1–9
Kleinstreuer C, Koo J (2004) Computational analysis of wall roughness effects for liquid flow in micro-conduits. J Fluids Eng 126:1–9
Theilade UR, Kjaer EM, Hansen HN (2003) The effect of mold surface topography on plastic part in-process shrinkage in injection molding. ANTEC 1:463–467
Smialek CD, Simpson CL (1998) Flow instabilities in thin-wall injection molding of thermoplastic polyurethane. ANTEC 3:3373–3377
Griffiths CA, Dimov SS, Pham DT (2006) Micro injection moulding: the effects of tool surface finish on melt flow behaviour. Multi Mater Micro Manuf Proc, Elsevier, Amsterdam, pp 1–4
Croce G, Agaro PD (2004) Numerical analysis of roughness effect on microtube heat transfer. Supperlattice Microst 35:601–616
Koo J, Kleinstreuer C (2003) Liquid flow in microchannels: experimental observations and computational analysis of microfluidics effects. J Micromech Microeng 13:568–579
Koo J, Kleinstreuer C (2005) Analysis of surface roughness effects on heat transfer in micro-conduits. Int J Heat Mass Transfer 48:2625–2634
Hu YD, Werner C, Li DQ (2003) Influence of three-dimensional roughness on pressure-driven flow through microchannels. J Fluids Eng 125:871–879
Qu WL, Mala GH, Li DQ (2000) Heat transfer for water flow in trapezoidal silicon microchannels. Int J Heat Mass Transfer 43:3925–3936
Mala GM, Li D (1999) Flow characteristics of water in microtubes. Int J Heat Fluid Flow 20(2):142–148
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zhang, H.L., Ong, N.S. & Lam, Y.C. Mold surface roughness effects on cavity filling of polymer melt in micro injection molding. Int J Adv Manuf Technol 37, 1105–1112 (2008). https://doi.org/10.1007/s00170-007-1060-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-007-1060-6