Abstract
An investigation has been made of the feasibility of friction stir welding of dissimilar lap joint of an aluminium plate to a copper plate, which is difficult to weld by fusion welding methods because of the formation of brittle intermetallic compounds (IMC). Although the level of bond strength was quite low, it exhibited a general tendency to increase with a rise in rotation speed. Various microstructures with different morphologies and properties were observed in the stirred zone of aluminium and Al/Cu interfacial region. Comparison of the fracture location with the microstructure suggests that IMC formed in the interfacial region was responsible for the low strength of the joints. X-ray diffraction from the fracture surfaces indicate that Al4Cu9, AlCu, and Al2Cu were the main intermetallic compounds formed in the interfacial region. The performance of the joints was improved significantly by using Zn intermediate layer between Al and Cu owing to limiting the formation of the harmful intermetallic compounds and distributing them over wider areas.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Nakui S., Kawakami K., Ueoka T., Tsujino: Welding structure of metal specimens welded using ultrasonic welding systems with linear and complex vibration welding tips, WCU, 2003, Paris, September 7–10, pp. 1273–1274.
Yilbas B.S., Sahin A.Z., Kahraman N., Al-Garni A.Z.: Friction welding of St-Al and Al-Cu materials, Journal of Metal Processing Technology, 1995, vol.49, No. 3–4, pp. 431–443.
Pinto M.A., Cheung N., Ierardi M.C.F., Garcia A.: Microstructural and hardness investigation of an aluminum-copper alloy processed by laser surface melting, Materials Characterization, 2003, vol. 50, No. 2–3, pp. 249–253.
Lee W.B., Yeon Y.M., Jung S.B.: Joint properties of Friction stir welded AZ31B-H24 magnesium alloy Materials Science and Technology, 2001, vol. 19, pp. 785–790.
Juhas M.C., Viswanathan G.B., Fraser H.L.: Microstructural evolution in a titanium alloy friction stir weld, Proc. Second Annual Symposium on Friction Stir Welding, Gothenburg, Sweden, June, 2000.
Won-Bae Lee, Seung-Boo Jung: The joint properties of copper by friction stir welding, Material letters, 2004, No. 58, pp. 1041–1046.
Thomas W.M., Threadgill P.L., Nicholas E.D.: Feasibility of friction stir welding steel, Science and Technology of Welding and Joining, 1999, vol. 4, No. 6, pp. 365–372.
Lienert T.J., Stellwag W.L., Grimmett J.R.B.B., Warke R.W.: Friction stir welding studies on mild steel, Welding Journal, 2003, No. 1, pp. 1–9.
Reynolds A.P., Wei Tang, Gnaupel-Herold T., Prask H.: Structure, properties, and residual stress of 304L stainless steel friction stir welds, Scripta Materialia, 2003, vol. 48, No. 9, pp. 1289–1294.
Ying Li, Murr L.E., McClure J.C.: Flow visualization and residual microstructures associated with the friction-stir welding of 2024 aluminum to 6061 aluminum, Material Science and Engineering A, vol. 271, No. 1–2, 1999, pp. 213–223.
Yoshikawa K., Harano T.: Numerically controlled friction stir welding in layered dissimilar metal materials of aluminum to steel, Proceedings of the third symposium on friction stir welding, Kobe, Japan, September 27–28, 2001.
Takehiko W., Atsushi Y., Hirohumi T.: Bonding of steel and aluminum alloy by interfacial active adhesion bonding method -Interfacial active adhesion bonding of dissimilar material with a rotating needle, Preprints of the national meeting of J.W.S., 2002, No. 71, pp. 446–447, (in Japanese).
Tsubaki M., Fukumoto M., Yasui T.: Evaluation of joining property between steel and aluminum by friction stirring, Preprints of the national meeting of J.W.S., spring 2003, No. 72, pp. 30–31, (in Japanese).
Elrefaey A., Takahashi M., Ikeuch K.: Friction Stir Welding of Aluminum-to-Steel Lap Joint, 175th Meeting of the Technical Commission on Welding Metallurgy, JWS, Doc. WM-1891–04, Feb. 2004.
Karlsson L., Berqvist E.L., Larsson H.: Application of friction stir welding to dissimilar welding, Annual assembly of IIW, Ljubljana, Slovenia, July 8–13, 2001.
Murr L.E., Li Y., Flores R.D., Trillo E.A.: Intercalation vortices and related microstructural features in the friction-stir welding of dissimilar metals, Material Research Innovation, 1998, vol. 2, No. 3, pp. 150–163.
Murr L.E., Flores R.D., McClure J.C., Liu G., Brown D.: Friction-stir welding: microstructral characterization, Material Research Innovation, 1998, vol. 1, No. 4, pp. 211–223.
Elrefaey A., Takahashi M., Ikeuch K.: Preliminary investigation of friction stir welding aluminum/copper lap Joints, IIW Pre Assembly Meeting on FSW, Nagoya, Japan, July 2004, pp. 275–285.
Sato Y.S., Kokawa H., Ikeda K., Enomoto M., Jogan S., Hashimoto T.: Microtexture in the friction-stir weld of an aluminium alloy, Metallurgical and Metals Transactions A, 2001, vol. 32A, No. 4, pp. 941–948.
Jata K.V., Semiatin S.L.: Continuous dynamic recrystallization during friction stir welding of high strength aluminum alloys, Scripta Materialia, 2000, vol. 43, No. 8, pp. 743–749.
Su J.Q., Nelson T.W., Mishra R., Mahoney M.: Microstructral investigation of friction stir welded 7050-T651 aluminum, Acta Materialia, 2003, vol. 51, No. 3, pp. 713–729.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Elrefaey, A., Takahashi, M. & Ikeuchi, K. Preliminary Investigation of Friction Stir Welding Aluminium/Copper Lap Joints. Weld World 49, 93–101 (2005). https://doi.org/10.1007/BF03266481
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF03266481