Abstract
Initiated at the interface of dissimilar elemental metal foils, a self-propagating, high-temperature synthesis (SHS) reaction can be used to produce a fully dense, well-bonded metal-intermetallic layered composite. In the research described here, aluminum foils were sandwiched between metal foils (Fe, Ni, Ti) and heated in a hot press to approximately the melting point of aluminum. An SHS reaction occurred at the metal-aluminum interface, consuming all of the aluminum foil and part of the metal foil, resulting in a strongly bonded metal-aluminide interface. Tensile tests conducted at room temperature revealed that composites can be designed to behave in a high-strength and high-toughness manner by altering the thicknesses of the elemental foils.
Similar content being viewed by others
References
J.H. Walters and H.E. Cline, “The Effect of Solidification Rate on Structure and High-Temperature Strength of the Eutectic NiAl-Cr,” Metal l. Trans. A, 1A (1970), pp. 1221–1229.
J.J. Brennen, “Increasing the Impact Strength of Si3N4 Through Fibre Reinforcement,” Special Ceramics 6, ed. P. Popper (Stoke-on-Trent, U.K.: British Ceramic Research Association, 1975), p. 123.
E. Fitzer and W. Remmele, “Possibilities and Limits of Metal Reinforced Refractory Suicides Especial ly Molybdenum Disilicide,” Proc. 5th Int. Conf. Comp. Matls.—ICCM-V, ed. W.C. Harrigan, Jr., J.R. Strife, and A.K. Dhingra (Warrendal e, PA: TMS, 1985), pp. 515–530.
P. Hing and G.W. Groves, “The Strength and Fracture Toughness of Polycrystal line Magnesium Oxide Containing Metal lic Particles and Fibres,” J. Mater. Sci., 7 (1972), pp. 427–434.
J.L. Chermant and F. Osterstock, “Fracture Toughness and Fracture of WC-Co Composites,” J. Mater. Sci., 11 (1976), pp. 1939–1951.
H.E. Deve et al., “Ductile Reinforcement Toughening of TiAl: Effects of Debonding and Ductility,” Acta Metal l, et Mater., 38 (1990), pp. 1491–1502.
V.C. Nardone and J.R. Strife, “NiAl-Based Microstructural ly Toughened Composites,” Metal l. Trans. A, 22A (1991), pp. 183–189.
M.J. Mal oney and R.J. Hecht, “Development of Continuous-Fiber-Reinforced MoSi2-Base Composites,” Mater. Sci. Engr., A155 (1992), pp. 19–31.
M.G. Mendiratta, J.J. Lewandowski, and D.M. Dimiduk, “Strength and Ductile-Phase Toughening in the Two-Phase Nb/ Nb5Si3 Al loys,” Metal l. Trans. A, 22A (1991) pp. 1573–1583.
K.T. VenkateswaraRao, W.O. Soboyejo, and R.O. Ritchie, “Ductile-Phase Toughening and Fatigue-Crack Growth in Nb Reinforced Molybdenum Disilicide Intermetal lic Composites,” Metal l. Trans. A, 23A (1992), pp. 2249–2257.
D.E. Al man, “The Effect of Ductile Phase (Nb) Reinforcement Morphology on the Mechanical Behavior of an Intermetal lic Matrix (MoSi2),” Ph.D. thesis, au]Rensselaer_Polytechnic Institute, Troy, New York (1992).
D.E. Alman et al., “Processing, Structure and Properties of MoSi2-Base Composites,” Mater. Sci. Engr., A155 (1992), pp. 85–93.
R.G. Rowe and D.W. Kelly, “The Synthesis and Eval uation of Nb3Al-Nb Laminated Composites,” Intermetal lic Matrix Composites II, ed. D.B. Miracle, D.L. Anton, and J.A. Graves (Pittsburgh, PA: MRS, 1992), pp. 411–416.
D.A. Hardwick, and R.C. Cordi, “Intermetal lic Matrix Composites by Physical Vapor Deposition,” Intermetal lic Matrix Composites, ed. D.L. Anton et al. (Pittsburgh, PA: MRS, 1990), pp. 65–70.
Z.A. Munir, “Synthesis of High Temperature materials by Self-Propagating Combustion Methods,” Bull. Amer. Ceram. Soc, 67(2) (1988), pp. 342–349.
Z.A. Munir, “Reaction Synthesis Process: Mechanisms and Characterization,” Metal l. Trans. A., 23A (1992), pp. 7–13.
Z.A. Munir, “The Synthesis and Consolidation of Powders by Self-Propagating Combustion Method,” Reviews in Particulate materials, 1 (1993), pp. 41–74.
A. Bose et al., “Elemental Powder Approaches to Ni3Al-Matrix Composites,“ /. Metal s, 40(9) (1988), pp. 14–17.
J.C. Rawers and W.R. Wrzesinski, “Reaction-Sintered Hot-Pressed TiAl,” J. Mater. Sci., 27 (1992), pp. 2877–2886.
D.E. Alman and N.S. Stoloff, “Powder Fabrication of Monolithic and Composite NiAl,” Intl. J. Powder. Met., 27 (1) (1991), pp. 29–41.
D.E. Alman and N.S. Stoloff, “Preparation of MoSi2/SiC Composites from Elemental Powders by Reactive Co-Synthesis,” Scripta Metal l. et Mater., 28 (1993), pp. 1525–1530.
G. Wang and M. Dahms, “Synthesizing Gamma-TiAl Al loys by Reactive Powder Processing,” JOM, 45(6) (1993), pp. 52–56.
L. Lu et al., “Reaction Synthesis of NbAl 3 Matrix Composites, Intermetal lic Matrix Composites, ed. D.L. Anton et al. (Pittsburgh, PA: MRS, 1990), pp. 79–87.
J. Kajuch, J.D. Rigney, and J.J. Lewandowski, “Processing and Properties of Nb5Si3 and Tough Nb5Si3/Nb Laminates,” Mater. Sci. Engr., A155 (1992), pp. 59–65.
H.E. Maupin and J.C. Rawers, “Metal-Intermetal lic Composites Formed by Reaction-Sintering Elemental Powders,” J. Mater. Sci. Letts., 12 (1993), pp. 540–541.
D.M. Matson and Z.A. Munir, “Combustion Synthesis of Intermetal lic Compounds Using Ti, Ni and Cu Wires,” Mater. Sci. Engr., A153 (1992), pp. 700–705.
U. Anselmi-Tamburini and Z.A. Munir, “The Propagation of a Solid-State Combustion Wave in Ni-Al Foils,” J. Appl. Phys., 66(10) (1989), pp. 5039–5045.
J.C. Rawers, D.E. Al man, and J.A. Hawk, “Overview: Layered Meta-Intermetal lic-Composites Formed by SHS Reactions,” Intl. J. Self-Prop. High Temp. Syn., 2 (1) (1993), pp. 12–24.
D.E. Alman, J.A. Hawk, and J.C. Rawers, “Microstructural and Failure Characteristics of Metal-Intermetal lic Layered Sheet Composites,” submitted to Metal. Trans. A (1993).
J.C. Rawers et al., “Formation of Sheet Metal-Intermetal lic Composites by Self-Propagating, High-Temperature Reactions,” submitted to J. Mater. Sci. Letts. (1993).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Alman, D.E., Hawk, J.A., Petty, A.V. et al. Processing intermetallic composites by self-propagating, high-temperature synthesis. JOM 46, 31–35 (1994). https://doi.org/10.1007/BF03220646
Issue Date:
DOI: https://doi.org/10.1007/BF03220646