Abstract
The effects of gas velocity (0.10–0.68 m/s), distributor geometry (opening area ratio, number of orifices and hole sizes) and the particle size distribution (wide and narrow) of polyethylene on the pressure fluctuation of the distributor and the local pressure drop in the beds have been determined in a gas-solid fluidized bed of 0.07-m I.D. and 0.7 m in height. The mean amplitude and the normalized standard deviation of the local pressure drop were determined by analyzing pressure fluctuation in the bed. The variation of the mean amplitude of the local pressure drop with the gas velocity is independent on the different distributors. The normalized standard deviation of the local pressure drop increased with increasing the ratio of the excess gas velocity to the minimum fluidization velocity and the lumped parameter of the distributor, hD. Also, the normalized standard deviation of the local pressure drop of polyethylene polymerized by Metallocene catalyst (narrow) is higher than that of polyethylene polymerized by Ziegler-Natta catalyst (wide).
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Burdett, I.D., Eisinger, R. S., Cai, P. and Lee, H.H., “Gas-Phase Fluidization Technology for Production of Polyolefins,” Fluidization, X., Kwauk, M., Li, J. and Yang, W. C., eds., United Eng. Found., New York, 39 (2001).
Cho, H., Han, G. and Ahn, G., “Characteristics of Slug Flow in a Fluidized Bed of Polyethylene Particles,”Korean J. Chem. Eng.,19, 183 (2001).
Cho, H., Han, G. and Ahn, G., “The Slug Flow Behavior of Polyethylene Particles Polymerized by Ziegler-Natta and Metallocene Catalysts,”Korean J. Chem. Eng.,18, 561 (2001).
Ergun, S., “Fluid Flow through Packed Columns,”Chem Eng. Prog.,48, 89 (1952).
Jiang, P., Bi, H., Liang, S. C. and Fan, L. S., “Hydrodynamic Behavior of Circulating Fluidized Bed with Polymeric Particles,”AIChE J.,40, 193 (1994).
Kunii, D. and Levenspiel, O., “Fluidization Engineering,” 2nd ed., Butterworth-Heinemann (1992).
Lee, S. H., Lee, D. H. and Kim, S. D., “Slug Characteristics of Polymer Particles in a Gas-Solid Fluidized Bed,”Korean J. Chem. Eng.,19, 351 (2002).
Lee, S. H., Lee, D. H. and Kim, S. D., “Slug Characteristics of Polymer Particles in a Fluidized Bed with Different Distributors,”Korean J. Chem. Eng.,18, 387 (2001).
Mcauley, K. B., Talbot, J. P. and Harris, T. J., “A Comparison of Two-Phase and Well-Mixed Models for Fluidized Polyethylene Reactors,”Chem. Eng. Sci.,49, 2035 (1994).
Stewart, P. S. B. and Davidson, J. F., “Slug Flow in Fluidized Beds,”Powder Techn.,1, 61 (1967).
Tsuchiya, K. and Nakanishi, O., “Gas Holdup Behavior in a Tall Bubble Column with Perforated Plate Distributors,”Chem. Eng. Sci.,47, 3347 (1992).
Yamashida, F. and Inoue, H., “Gas Holdup in Bubble Columns,”J. Chem. Eng. Japan,8, 334 (1975).
Author information
Authors and Affiliations
Corresponding author
Additional information
This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.
Rights and permissions
About this article
Cite this article
Yang, D.H., Lee, D.H. & Han, G.Y. Pressure fluctuation characteristics of polyethylene particles in a gas-solid fluidized bed with different distributors. Korean J. Chem. Eng. 19, 1112–1116 (2002). https://doi.org/10.1007/BF02707241
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF02707241