Abstract
The adhesion between rubber compound and brass-plated steel cord of rubber-brass composites with different cure levels was investigated in relation to the formation and growth of their adhesion interphase examined with AES spectroscopy. The optimum-cured adhesion sample showed a maximum pullout force, but the pullout forces of samples under-cured and over-cured were low. The adhesion property of under-cured adhesion samples enhanced with humidity aging due to further curing of rubber and supplementary growth of the adhesion interphase. Cure level exhibiting good adhesion was discussed based on the composition and structure of the adhesion interphase and the crosslinking density of the rubber layer attached to the interphase.
Article PDF
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
References
Cho, P. L., Jeon, G. S., Ryu, S. K. and Seo, G., “Adhesion between Rubber Compound and Copper-Füm-Plated Steel Cord”,J. Adhesion,70, 241 (1999).
Fernando, M. S. D., Cudby, P. E. F. and Cook, S., “The Influence of Moulding Temperature on the Strength of Natural Rubber to Metal Bonded Joints”,Kautsch. Gummi, Kunstst.,53, 194 (2000).
Hammer, G. E., “A New Look at the Steel Cord-Rubber Adhesive Interphase by Chemical Depth Profiling”,J. Vac. Sci. Technol. A,19, 2846 (2001).
Holtkamp, D., Elschner, A., Muller, G. and Pieroth, M., “Novel Model System to Study the Influence of Rubber Compound Formulation on the Structure and Composition of the Rubber-Brass Interphase”,Surf. Interface Anal,23, 155 (1995).
Jeon, G. S., Han, M. H. and Seo, G, “Enhancing Adhesion Properties between Rubber Compound and Brass-Plated Steel Cord by Incorporating Silica into Rubber”,J. Adhesion Sci. Technol.,13, 153 (1999).
Jeon, G. S. and Seo, G, “Influence of Cure Conditions on the Adhesion of Rubber Compound to Brass-Plated Steel Cord. Part I. Cure Temperature”,J. Adhesion,76, 201 (2001a).
Jeon, G. S. and Seo, G, “Influence of Cure Conditions on the Adhesion of Rubber Compound to Brass-Plated Steel Cord. Part II. Cure Time”,J. Adhesion,76, 223 (2001b).
Jeon, G. S. and Seo, G., “Promotion Effect of a Chlorotriazine Derivative on the Adhesion Between Rubber Compounds and a Brass-Plated Steel Cord”,J. Adhesion Sci. Technol.,15, 689 (2001c).
Kurbatov, G. G., Beshenkov, V. G. and Zaporozchenko, V. L., “AES and Factor Analysis Study of Cord-Oxidized Brass Layers and Rubber-to-Brass Interface Chemical Composition”,Surf. Interface Anal,17, 779 (1991).
Persooner, P., De Volder, P. and De Gryse, R, “The Influence of Cobalt on the Oxysulfidation of Brass”,Solid State Commun.,92, 675 (1994).
Seo, G., “Stabilizing the Adhesion Interphase between Rubber Compound and Brass Film by the Addition of Resorcinol Formaldehyde Resin to the Rubber”,J. Adhesion Sci. Technoi,11, 1433 (1997).
van Ooij, W. J., “Fundamental Aspects of Rubber Adhesion to Brass-Plated Steel Tire Cords”,Rubber Chem. Technoi,52, 605 (1979).
Author information
Authors and Affiliations
Corresponding author
Additional information
This paper is dedicated to Professor Hyun-Ku Rhee on the occasion of his retirement from Seoul National University (Gon Seo).
Rights and permissions
About this article
Cite this article
Jeon, G.S., Seo, G. Effects of cure levels on adhesion between rubber and brass in the composites made up of rubber compound and brass-plated steel cord. Korean J. Chem. Eng. 20, 496–502 (2003). https://doi.org/10.1007/BF02705555
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF02705555