Abstract
Lead-free solders, including Sn-58Bi, Sn-52In, and Sn-3.5Ag, are potential replacements for Sn-37Pb solder in low-cost electronic assembly. This paper reviews the literature on the microstructure and mechanical properties of these alloys. Because of the processing and testing conditions, many of the data are not predictive for electronic assembly applications. However, eutectic Sn-Bi seems to have properties approaching those of eutectic Sn-Pb under most conditions, while eutectic Sn-In seems far inferior in most respects. Eutectic Sn-Ag has many promising characteristics, but its relatively high melting temperature may preclude its use for this type of application.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
B.R. Allenby, et al.Proc. Surface Mount Intl. 1992, p. 1.
P.G. Harris and M.A. Whitmore,Circuit World 19 (2), 25 (1993).
C. Melton, A. Skipor and J. Thome,NepconWest. ’93, p. 1489.
R.W. Wild.Tech. Rpt. 171200408, IBM Federal Systems Division Laboratory, Owego NY 1971.
J.H. Vincent et al.,Circuit World 19 (3), 32 (1993).
Z. Mei and J.W. Morris, Jr.,ASME Winter Annual Meeting, Dec. 1–6, 1991, Atlanta, GA, 91-WA-EEP-20.
J. Seyyedi,Soldering and Surface Mount Tech. 13 (2), 26 (1993).
Z. Mei and J.W. Morris, Jr.,J. Electron. Mater. 21,599(1992).
E.W. Hare, R. Corwin and E.K. Riemer,Proc. ASM Intl. Elec. Packaging Math, and Processes Conf., Oct. 1985, (Materials Park, OH: ASM Intl., 1986), p. 109.
K. Seelig, D. Sklarski. L. Johnson and J. Sartell,Nepcon East. 1987.
Z. Mei and J.W. Morris, Jr.,J. Electron. Mater. 21,401(1992).
J.L. Freer and J.W. Morris, Jr.,J. Electron. Mater. 21, 647 (1992).
J.L. Freer Goldstein and J.W. Morris. Jr., submitted toMet. Trans. A.
M.E. Warwick and S.J. Muckett,Circuit World 9 (4), 5 (1983).
J. Haimovich,Weld. Res. Supp. March, 102s (1989).
L.E. Felton, C.H. Raeder and D.B. Knorr.JOM 45 (7), 28 (1993).
A.D. Romig, F.G. Yost and P.F. Hlava,Microbeam Analysis— 1984, eds. A.D. Romig, Jr. and J.I. Goldstein, (San Francisco Press, 1984), p. 87.
G. Humpston and D.M. Jacobson,Principles of Soldering and Brazing, (Materials Park, OH: ASM Intl., 1993).
R. Satoh,Thermal Stress and Strain in Microelectronics Packaging, ed. J.H. Lau, (New York: Van Nostrand Reinhold, 1993), p. 500.
K.G. Schmitt-Thomas andS.Wege,Brazing and Soldering 11, Autumn, 27(1986).
R. Strauss and S. Smernos,The Bulletin of the Bismuth Institute 49, 1 (1986).
C.A. MacKay and W.D. von Voss,Mater. Sci. Technol. 1, 240 (1985).
P.T. Vianco, F.M. Hosking and J.A. Rejent,Nepcon West 1992, p. 1730.
W.J. Tomlinson and I. Collier,Mater. Sci. Eng. 1835 (1987).
F.M. Hosking, P.T. Vianco, C.L. Hernandez and J.A. Rejent,Proc. Surf. Mount Intl., San Jose, CA, Aug. 29–Sept. 2, 1993, p. 476.
C. Melton,Proc. 43rd ECTC, June 1–4, 1993 Orlando, FL (New York: IEEE), p. 1008.
F.M. Hosking, P.T. Vianco and D.R. Frear,Sandia National Laboratories Rpt. No. SAND90-3248C.
J.W. Morris, Jr. and Z. Mei,Solder Mechanics-A State of the Art Assessment, eds., D.R. Frear et al., (Warrendale, PA: The Minerals, Metals and Materials Society, 1991).
J.S. Hwang and R.M. Vargas,Soldering and Surf. Mount Tech. 4(2)27(1990).
C.J. Thwaites and W.B. Hampshire,Weld. Res. Supp. (1976), p. 323s.
W.J. Tomlinson and A. Fullylove,J Mater. Sci. 27, 5777 (1992).
L.E. Felton. C.H. Raeder. C.K. Havasy and D.B. Knorr,1992 IEEE/CHMTInt’l. Eke. Mfg. Tech. Symp., Sept. 28–30,1992, Baltimore, MD, p. 300.
R.W. Wild,NEPCON1974, p. 105.
M. Warwick,Brazing and Soldering 8, Spring, 20 (1985).
Z. Guo, A.F. Sprecher, Jr., H. Conrad and M. Kim,Materials Developments in Microelectronic Packaging, (Materials Park, OH: ASM, 1991).
L. Quan, D.R. Frear, D. Grivas and J.W. Morris, Jr.,J. Electron. Mater. 16, 203 (1987).
D.R. Frear, Ph.D. Thesis, University of California-Berkeley, June 1987.
S. Pattanaik and V. Raman,Materials Developments in Micro- electronic Packaging: Performance and Reliability, (Materials Park: OH: ASM Intl., 1991), p. 251.
J.R. Getten and R.C. Senger.IBMJ. Res. Dev. 26,379 (1982).
J. London and D.W. Ashall,Brazing and Soldering 10, Spring 17 (1986).
J.L. Freer Goldstein and J.W. Morris, Jr.,J. Elect. Mater. 23, 477 (1994).
C. Lea,A Scientific Guide to Surface Mount Technology, (Ayr, Scotland: Electrochemical Publications, 1988).
S. Wege,Proc. Conf. Weichloeten in Forschung und Praxis Munich. Feb. 1986, DVS Berichte nr. 104, p. 134.
J.W. Morris, Jr., J.L. Freer Goldstein and Z. Mei,The Mechan- ics of Solder Alloy Interconnects, eds., D.R. Frear, H. Morgan, S. Burchett and J.H. Lau, (New York: Van Nostrand Reinhold, 1994), p. 7.
D.M. Jarboe,Bendix Kansas City Div. internal report, 1980, DBX-613-2341. Referenced in D.R. Frear,Solder Mechanics- A State of the Art Assessment, eds., D.R. Frear. et al. (Warrendale, PA: The Minerals, Metals and Materials Society, 1991).
J.L. Marshall and S.R. Walter,Intl. J. Hybrid Microelectron. 10, 11 (1987).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Glazer, J. Microstructure and mechanical properties of Pb-free solder alloys for low-cost electronic assembly: A review. J. Electron. Mater. 23, 693–700 (1994). https://doi.org/10.1007/BF02651361
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02651361