Abstract
The formation of elementary chip in the cutting of difficult machines is investigated. A method is developed for determining the optimal cutting conditions on the basis of the temperature of best tool performance with elementary-chip formation.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Zelinskii, A.N. and Nazarov, A.K., Influence of the geometric parameters of the tool on the type of chip, Almazno-abrazivnaya obrabotka: Konf. instrumental’shchikov Zapadnogo Urala (Diamond–Abrasive Machining: Conference of Western Ural Tool Specialists), Perm, 1967, pp. 128–131.
Petrushin, S.I. and Proskokov, A.V., Theory of constrained cutting: Chip formation with a developed plastic-deformation zone, Russ. Eng. Res., 2010, vol. 30, no. 1, pp. 45–50.
Afonasov, A.I. and Lasukov, A.A., Elementary chip formation in metal cutting, Russ. Eng. Res., 2014, vol. 34, no. 3, pp. 152–155.
Rozenberg, A.M. and Zimin, Yu.P., Dynamics of fast cutting, Stanki Instrum., 1951, no. 9, pp. 11–13.
Proskuryakov, S.L., More Efficient Machining of High-Temperature Alloys by Optimizing the Cutting Conditions, Cand. Sci. Dissertation, Gorky, 1989.
Priemyshev, A.V., Shchukin, A.N., and Priemyshev, A.A., Chip morphology in grinding and microcutting, Instrum. Tekhnol., 2011, no. 5/6, p. 45.
Antic, A., Petrovic, P.B., Zeljkovic, M., et al., The influence of tool wear on the chip-forming mechanism and tool vibrations, Mater. Technol., 2012, vol. 46, pp. 279–285.
Guohe, L., Minjie, W., and Chunzheng, D., Adiabatic shear critical condition in the high-speed cutting, J. Mater. Proc. Technol., 2009, vol. 209, pp. 1362–1367.
Krivoukhov, V.A. and Chubarov, A.D., Obrabotka rezaniem titanovykh splavov (Cutting of Titanium Alloys), Moscow: Mashinostroenie, 1970.
Sozinov, A.I., Theoretical Principles of More Efficient Rough Cutting of Titanium-Alloy Blanks, Doctoral Dissertation, Moscow, 1994.
Bobrov, V.F. and Sedel’nikov, A.I., Influence of the type of chip and buildup on the wear of hard-alloy cutters, Stanki Instrum., 1976, no. 7, pp. 30–32.
Zelinskii, A.N., Improvement in Machining Productivity by Controlling Cut-Layer Deformation, Cand. Sci. Dissertation, Tula, 1974.
Artamonov, E.V. and Efimovich, I.A., Laser-interferometric data regarding the stress–strain state of tools in nonsteady cutting, Optiko-geometricheskie metody issledovaniya deformatsii i napryazhenii: Sb. Vsesoyuzn. nauch.-tekhn. konf. (Optical–Geometric Methods of Stress and Strain Investigation: Proceedings of a National Conference), Chelyabinsk, 1986, pp. 95–96.
Artamonov, E.V., Prochnost’ i rabotosposobnost’ smennykh tverdosplavnykh plastin sbornykh rezhushchikh instrumentov (Strength and Performance of Replaceable Hard-Alloys Plates in Composite Cutting Tools), Tyumen’: Vektor Buk, 2003.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © A.A. Lasukov, 2015, published in Vestnik Mashinostroeniya, 2015, No. 6, pp. 74–77.
About this article
Cite this article
Lasukov, A.A. Selection of machining conditions in terms of the temperature dependence of chip formation. Russ. Engin. Res. 35, 679–681 (2015). https://doi.org/10.3103/S1068798X15090129
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X15090129