Abstract
Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.
To address this, Metso’s HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Gerrard, M., Costello, B., and Morley, C., 2004, “Operational experiences and performance assessment of HPGR technology at Argyle Diamond Mine,” The AusIMM New Leaders’ Conference, April 21–22, 2004, Ballarat, Victoria, Australia, pp. 63–73.
Hart, S., Parker, B., Rees, T., Manesh, A., and Mcgaffin, I., 2011, “Commissioning and ramp up of the HPGR circuit at Newmont Boddington Gold,” Proceedings of 2011 International Autogenous Grinding Semiautogenous Grinding and High Pressure Grinding Roll Technology, Vancouver, British Columbia, Canada, Paper No. 041.
Herman, V.S., Harbold, K.A., Mular, M.A., and Biggs, L.J., 2015, “Building the world’s largest HPGR–the HRC3000 at the Morenci Metcalf concentrator,” SAG 2015 Conference Proceedings, Vancouver, British Columbia, Canada.
Klymowsky, R., Patzelt, N., Knecht, J., and Burchardt, E., 2006, “An Overview of HPGR Technology,” Proceedings of SAG 2006, Vancouver, British Columbia, Canada, IV-11–IV-26.
Knorr, B., Elkin, N., Mayfield, N., Mular, M.A., and Whalen, D., 2015, “Pilot study of various HPGR circuit arrangements and crusher configurations,” SAG 2015 Conference Proceedings, Vancouver, British Columbia, Canada.
Knorr, B., Herman, V., and Whalen, D., 2013, “HRC™: Taking HPGR Efficiency to the Next Level by Reducing Edge Effect,” Procemin 2013, Santiago, Chile.
Morley, C., 2006, “High pressure grinding rolls–a technology review,” Advances in Comminution, Society for Mining, Metallurgy and Exploration Inc., Englewood, CO, pp. 15–39.
Morley, C., 2010, “HPGR-FAQ,” The Journal of The Southern African Institute of Mining and Metallurgy, Vol. 110, March 2010, pp. 107–115.
Morrell, S., Lim, W., Shi, F., and Tondo, L., 1997, “Modelling of the HPGR Crusher,” SME Annual Conference & Expo, Society for Mining, Metallurgy and Exploration Inc., Englewood, CO, pp. 117–126.
Mular, M.A., Hoffert, J.R., and Koski, S.M., 2015, “Design and operation of the Metcalf Concentrator comminution circuit,” SAG 2015 Conference Proceedings, Vancouver, British Columbia, Canada.
Rosario, P., and Hall, R., 2008, “A structured approach to the evaluation of the energy requirements of HPGR and SAG mill circuits in hard ore applications,” Proceedings of Comminution 2008.
Van der Meer, F., 2010, “High pressure grinding rolls scale-up and experiences,” XXV International Mineral Processing Congress (IMPC) 2010 Proceedings, Brisbane, Queensland, Australia, Paper No. 194.
Author information
Authors and Affiliations
Additional information
Paper number MMP-15-031.
Discussion of this peer-reviewed and approved paper is invited and must be submitted to SME Publications Dept. prior to Aug. 31, 2016.
Rights and permissions
About this article
Cite this article
Knorr, B., Herman, V. & Whalen, D. A closer look at increasing HPGR efficiency through reductions in edge effect. Mining, Metallurgy & Exploration 33, 1–6 (2016). https://doi.org/10.19150/mmp.6461
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.19150/mmp.6461