Abstract
Compared with traditional isobaric combustion, continuous rotating detonation (CRD) has been theoretically proved to be a more efficient combustion mode with higher thermal cycle efficiency. However, the realization and stable operating of liquid kerosene detonation is still a challenge. As a major component of kerosene pyrolysis products after regenerative cooling, ethylene is a transitional hydrocarbon fuel from kerosene to hydrogen and it is worth studying. In this paper, a series of 2D numerical simulations are conducted to investigate the effects of the injection nozzle on the ethylene-air CRD. Three geometrical parameters of the nozzle are thoroughly tested including the distance between two neighboring nozzle centers, the nozzle exit width, and the slant angle of the nozzle. The results show that an ethylene-air detonation wave is realized and it propagates stably. A small distance between two neighboring nozzle centers is conducive to improving the strength of the CRD wave and leads to greater feedback pressure into the plenum. As the nozzle exit width increases, the strength of the CRD wave and the feedback pressure into the plenum both increase. The CRD wave propagation velocity is greatly improved and the feedback pressure into the plenum is significantly reduced when the slant angle of the nozzle is positive. By contrast, a sizeable reduction in velocity is found when the angle is negative. The co-rotating two-wave propagation mode is observed when the angle is 30°, and the highest CRD propagation velocity and the lowest feedback pressure are both obtained when the angle is 60°.
概要
目的
通过数值模拟分析乙烯-空气连续旋转爆震波的流场特征,探讨喷孔几何参数(喷孔间距、喷孔出口宽度和喷孔倾斜角)对乙烯-空气连续旋转爆震波传播特性的影响,为降低乙烯-空气连续旋转爆震波传播速度亏损及爆震波对上游积气腔的反馈压力提供一些设计思路。
创新点
1. 采用含积气腔和喷孔的喷注模型进行乙烯-空气连续旋转爆震波的数值仿真,观察到了爆震波的模态转换过程并定量分析了爆震波对积气腔的反馈压力;2. 通过改变喷孔的倾斜角,在提高爆震波传播速度的同时减小了积气腔内的反馈压力。
方法
1. 通过FLUENT进行数值仿真,分析乙烯-空气连续旋转爆震波的基本流场结构(图7和9)和爆震波传播模态的转换过程(图17)。2. 通过在积气腔和燃烧室内设置压力监测点,得到积气腔和燃烧室内的压力记录曲线(图8、10、13、14、18和20);通过压力曲线,计算爆震波的平均传播速度和积气腔内压力的相对标准差。3. 通过对比分析,总结喷孔几何参数对爆震波传播速度和积气腔内反馈压力的影响(图11、15和19)。
结论
1. 喷孔间距对连续旋转爆震波的强度和积气腔的反馈压力都有影响;较小的喷孔间距有助于提高爆震波的强度,但也会引起积气腔内更高的反馈压力。2. 随着喷孔出口宽度的增大,爆震波的强度增强,也使积气腔内的反馈压力显著增加。3. 喷孔倾斜角对爆震波的传播特性和积气腔内的反馈压力有重要影响:当喷孔沿爆震波传播方向倾斜时,爆震波的传播速度明显提高;反之,爆震波的传播速度明显降低。采用倾斜喷注时,积气腔内的反馈压力显著降低,并且喷管倾斜程度越大,积气腔内的压力越稳定。4. 倾斜喷注可以引起爆震波传播模态的转变;当倾斜角为30°时,出现了同向双波传播模态。5. 预着火产生的热点和预混气沿爆震波传播方向的分速度有利于形成新的爆震波。
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Change history
07 March 2022
An Erratum to this paper has been published: https://doi.org/10.1631/jzus.A20e0314
References
Anand V, George ACS, Driscoll RB, et al., 2015. Statistical treatment of wave instability in rotating detonation combustors. Proceedings of the 53rd AIAA Aerospace Sciences Meeting. https://doi.org/10.2514/6.2015-1103
Anand V, George AS, Driscoll R, et al., 2016a. Analysis of air inlet and fuel plenum behavior in a rotating detonation combustor. Experimental Thermal and Fluid Science, 70:408–416. https://doi.org/10.1016/j.expthermflusci.2015.10.007
Anand V, George AS, Driscoll R, et al., 2016b. Investigation of rotating detonation combustor operation with H2-air mixtures. International Journal of Hydrogen Energy, 41(2):1281–1292. https://doi.org/10.1016/j.ijhydene.2015.11.041
Bykovskii FA, Vedernikov EF, 1996. Self-sustaining pulsating detonation of gas-mixture flow. Combustion, Explosion and Shock Waves, 32(4):442–448. https://doi.org/10.1007/BF01998496
Cai XD, Liang JH, Deiterding R, et al., 2016. Adaptive mesh refinement based simulations of three-dimensional detonation combustion in supersonic combustible mixtures with a detailed reaction model. International Journal of Hydrogen Energy, 41(4):3222–3239. https://doi.org/10.1016/j.ijhydene.2015.11.093
Davidenko DM, Gökalp I, Kudryavtsev AN, 2007. Numerical simulation of the continuous rotating hydrogen-oxygen detonation with a detailed chemical mechanism. West-east High Speed Flow Field Conference, p.19–22.
Driscoll R, George AS, Gutmark EJ, 2016. Numerical investigation of injection within an axisymmetric rotating detonation engine. International Journal of Hydrogen Energy, 41(3):2052–2063. https://doi.org/10.1016/j.ijhydene.2015.10.055
Frolov SM, Dubrovskii AV, Ivanov VS, et al., 2013. Three-dimensional numerical simulation of the operation of a rotating-detonation chamber with separate supply of fuel and oxidizer. Russian Journal of Physical Chemistry B, 7(1):35–43. https://doi.org/10.1134/S1990793113010119
Fujii J, Kumazawa Y, Matsuo A, et al., 2016. Numerical investigation on detonation velocity in rotating detonation engine chamber. Proceedings of the Combustion Institute, 36(2):2665–2672. https://doi.org/10.1016/j.proci.2016.06.155
Gaillard T, Davidenko D, Dupoirieux F, 2017. Numerical simulation of a rotating detonation with a realistic injector designed for separate supply of gaseous hydrogen and oxygen. Acta Astronautica, 141:64–78. https://doi.org/10.1016/j.actaastro.2017.09.011
Hishida M, Fujiwara T, Wolanski P, 2009. Fundamentals of rotating detonations. Shock Waves, 19(1):1–10. https://doi.org/10.1007/s00193-008-0178-2
Huang SY, Zhou J, Liu SJ, et al., 2019. Effects of pintle injector on ethylene-air rocket-based continuous rotating detonation. Acta Astronautica, 164:311–320. https://doi.org/10.1016/j.actaastro.2019.08.019
Huang W, Chang JT, Yan L, 2020. Mixing and combustion in supersonic/hypersonic flows. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 21(8):609–613. https://doi.org/10.1631/jzus.A20MCSF1
Kindracki J, Wolański P, Gut Z, et al., 2011. Experimental research on the rotating detonation in gaseous fuels-oxygen mixtures. Shock Waves, 21(2):75–84. https://doi.org/10.1007/s00193-011-0298-y
Lei ZD, Chen ZW, Yang XQ, et al., 2020a. Operational mode transition in a rotating detonation engine. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 21(9):721–733. https://doi.org/10.1631/jzus.A1900349
Lei ZD, Yang XQ, Ding J, et al., 2020b. Performance of rotating detonation engine with stratified injection. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 21(9):734–744. https://doi.org/10.1631/jzus.A1900383
Li BX, Wu YW, Weng CS, et al., 2018. Influence of equivalence ratio on the propagation characteristics of rotating detonation wave. Experimental Thermal and Fluid Science, 93:366–378. https://doi.org/10.1016/j.expthermflusci.2018.01.014
Lin W, Zhou J, Liu SJ, et al., 2015. Experimental study on propagation mode of H2/air continuously rotating detonation wave. International Journal of Hydrogen Energy, 40(4):1980–1993. https://doi.org/10.1016/j.ijhydene.2014.11.119
Liu M, Zhou R, Wang JP, 2015. Numerical investigation of different injection patterns in rotating detonation engines. Combustion Science and Technology, 187(3):343–361. https://doi.org/10.1080/00102202.2014.923411
Liu SJ, Lin ZY, Sun MB, et al., 2011. Thrust vectoring of a continuous rotating detonation engine by changing the local injection pressure. Chinese Physics Letters, 28(9): 094704. https://doi.org/10.1088/0256-307X/28/9/094704
Liu SJ, Peng HY, Liu WD, et al., 2020. Effects of cavity depth on the ethylene-air continuous rotating detonation. Acta Astronautica, 166:1–10. https://doi.org/10.1016/j.actaastro.2019.09.038
Liu YS, Wang YH, Li YS, et al., 2015. Spectral analysis and self-adjusting mechanism for oscillation phenomenon in hydrogen-oxygen continuously rotating detonation engine. Chinese Journal of Aeronautics, 28(3):669–675. https://doi.org/10.1016/j.cja.2015.03.006
Meng QY, Zhao NB, Zheng HT, et al., 2018. Numerical investigation of the effect of inlet mass flow rates on H2/air non-premixed rotating detonation wave. International Journal of Hydrogen Energy, 43(29):13618–13631. https://doi.org/10.1016/j.ijhydene.2018.05.115
Morris C, 2005. Axisymmetric modeling of pulse detonation rocket engines. Proceedings of the 41st AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit. https://doi.org/10.2514/6.2005-3508
Naples A, Hoke J, Schauer F, 2015. Experimental investigation of a rotating detonation engine injector temporal response. Proceedings of the 53rd AIAA Aerospace Sciences Meeting. https://doi.org/10.2514/6.2015-1104
Nicholls JA, Cullen RE, Ragland KW, 1966. Feasibility studies of a rotating detonation wave rocket motor. Journal of Spacecraft and Rockets, 3(6):893–898. https://doi.org/10.2514/3.28557
Nikitin VF, Dushin VR, Phylippov YG, et al., 2009. Pulse detonation engines: technical approaches. Acta Astronautica, 64(2–3):281–287. https://doi.org/10.1016/j.actaastro.2008.08.002
Nordeen CA, Schwer D, Schauer F, et al., 2016. Role of inlet reactant mixedness on the thermodynamic performance of a rotating detonation engine. Shock Waves, 26(4):417–428.
Peng HY, Liu WD, Liu SJ, et al., 2019a. The effect of cavity on ethylene-air continuous rotating detonation in the annular combustor. International Journal of Hydrogen Energy, 44(26):14032–14043. https://doi.org/10.1016/j.ijhydene.2019.04.017
Peng HY, Liu WD, Liu SJ, et al., 2019b. Realization of methane-air continuous rotating detonation wave. Acta Astronautica, 164:1–8. https://doi.org/10.1016/j.actaastro.2019.07.001
Rankin BA, Fotia M, Paxson DE, et al., 2015. Experimental and numerical evaluation of pressure gain combustion in a rotating detonation engine. Proceedings of the 53rd AIAA Aerospace Sciences Meeting. https://doi.org/10.2514/6.2015-0877
Schwer D, Kailasanath K, 2011. Numerical study of the effects of engine size on rotating detonation engines. Proceedings of the 49th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition. https://doi.org/10.2514/6.2011-581
Schwer D, Kailasanath K, 2012. Feedback into mixture plenums in rotating detonation engines. Proceedings of the 50th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition. https://doi.org/10.2514/6.2012-617
Schwer D, Kailasanath K, 2013. Fluid dynamics of rotating detonation engines with hydrogen and hydrocarbon fuels. Proceedings of the Combustion Institute, 34(2):1991–1998. https://doi.org/10.1016/j.proci.2012.05.046
Schwer D, Corrigan A, Taylor B, et al., 2013. On reducing feedback pressure in rotating detonation engines. Proceedings of the 51st AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition. https://doi.org/10.2514/6.2013-1178
Shao YT, Liu M, Wang JP, et al., 2010. Numerical investigation of rotating detonation engine propulsive performance. Combustion Science and Technology, 182(11–12): 1586–1597. https://doi.org/10.1080/00102202.2010.497316
Shi W, Tian Y, Zhang WZ, et al., 2020. Experimental investigation on flame stabilization of a kerosene-fueled scramjet combustor with pilot hydrogen. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 21(8):663–672. https://doi.org/10.1631/jzus.A1900565
Singh DJ, Jachimowski CJ, 1994. Quasiglobal reaction model for ethylene combustion. AIAA Journal, 32(1):213–216. https://doi.org/10.2514/3.11972
Smirnov NN, Betelin VB, Nikitin VF, et al., 2015. Accumulation of errors in numerical simulations of chemically reacting gas dynamics. Acta Astronautica, 117:338–355. https://doi.org/10.1016/j.actaastro.2015.08.013
Smirnov NN, Nikitin VF, Stamov LI, et al., 2018. Rotating detonation in a ramjet engine three-dimensional modeling. Aerospace Science and Technology, 81:213–224. https://doi.org/10.1016/j.ast.2018.08.003
Stewart DS, Kasimov AR, 2006. State of detonation stability theory and its application to propulsion. Journal of Propulsion and Power, 22(6):1230–1244. https://doi.org/10.2514/1.21586
Sun J, Zhou J, Liu SJ, et al., 2017. Effects of injection nozzle exit width on rotating detonation engine. Acta Astronautica, 140:388–401. https://doi.org/10.1016/j.actaastro.2017.09.008
Sun J, Zhou J, Liu SJ, et al., 2018a. Numerical investigation of a rotating detonation engine under premixed/non-premixed conditions. Acta Astronautica, 152:630–638. https://doi.org/10.1016/j.actaastro.2018.09.012
Sun J, Zhou J, Liu SJ, et al., 2018b. Plume flowfield and propulsive performance analysis of a rotating detonation engine. Aerospace Science and Technology, 81:383–393. https://doi.org/10.1016/j.ast.2018.08.024
Sun J, Zhou J, Liu SJ, et al., 2019. Effects of air injection throat width on a non-premixed rotating detonation engine. Acta Astronautica, 159:189–198. https://doi.org/10.1016/j.actaastro.2019.03.067
Sun YC, Cai Z, Wang TY, et al., 2020. Numerical study on cavity ignition process in a supersonic combustor. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 21(10):848–858. https://doi.org/10.1631/jzus.A1900419
Taki S, Fujiwara T, 1978. Numerical analysis of two-dimensional nonsteady detonations. AIAA Journal, 16(1): 73–77. https://doi.org/10.2514/3.60859
Voitsekhovskii BV, 1959. Stationary spin detonation. Doklady Akademii Nayk USSR, 129(6):1254–1256.
Wang P, Shen CB, 2019. Characteristics of mixing enhancement achieved using a pulsed plasma synthetic jet in a supersonic flow. Journal of Zhejiang University-SCIENCE A (Applied Physics & Engineering), 20(9): 701–713. https://doi.org/10.1631/jzus.A1900130
Wang YH, Le JL, Wang C, et al., 2018. A non-premixed rotating detonation engine using ethylene and air. Applied Thermal Engineering, 137:749–757. https://doi.org/10.1016/j.applthermaleng.2018.04.015
Xie QF, Wen HC, Li WH, et al., 2018. Analysis of operating diagram for H2/air rotating detonation combustors under lean fuel condition. Energy, 151:408–419. https://doi.org/10.1016/j.energy.2018.03.062
Yao S, Han X, Liu Y, et al., 2017. Numerical study of rotating detonation engine with an array of injection holes. Shock Waves, 27(3):467–476. https://doi.org/10.1007/s00193-016-0692-6
Zhdan SA, 2008. Mathematical model of continuous detonation in an annular combustor with a supersonic flow velocity. Combustion, Explosion, and Shock Waves, 44(6): 690–697. https://doi.org/10.1007/s10573-008-0104-z
Zhdan SA, Mardashev AM, Mitrofanov VV, 1990. Calculation of the flow of spin detonation in an annular chamber. Combustion, Explosion and Shock Waves, 26(2):210–214. https://doi.org/10.1007/BF00742414
Zhdan SA, Bykovskii FA, Vedernikov EF, 2007. Mathematical modeling of a rotating detonation wave in a hydrogen-oxygen mixture. Combustion, Explosion, and Shock Waves, 43(4):449–459. https://doi.org/10.1007/s10573-007-0061-y
Author information
Authors and Affiliations
Contributions
Jin ZHOU and Shi-jie LIU participated in the design of this numerical study. Wei-jie FAN carried out the simulations and analyzed the results under their guidance. Hao-yang PENG provided important suggestions on the improvement of simulation. All authors reviewed and revised the manuscript carefully, and approved the content of the manuscript.
Corresponding author
Additional information
Conflict of interest
Wei-jie FAN, Jin ZHOU, Shi-jie LIU, and Hao-yang PENG declare that they have no conflict of interest.
Project supported by the National Natural Science Foundation of China (Nos. 51776220 and 91541103) and the Postgraduate Scientific Research Innovation Project of Hunan Province, China
Rights and permissions
About this article
Cite this article
Fan, Wj., Zhou, J., Liu, Sj. et al. Effects of the geometrical parameters of the injection nozzle on ethylene-air continuous rotating detonation. J. Zhejiang Univ. Sci. A 22, 547–563 (2021). https://doi.org/10.1631/jzus.A2000314
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1631/jzus.A2000314