Abstract
In this paper, to improve the power conversion efficiencies (PCEs) of quantum dot-sensitized solar cells (QDSSCs) based on CdS-sensitized TiO2 nanotube (TNT) electrodes, two methods are employed on the basis of our previous work. First, by replacing the traditional single-sided working electrodes, double-sided transparent TNT/ITO (DTTO) electrodes are prepared to increase the loading amount of quantum dots (QDs) on the working electrodes. Second, to increase the light absorption of the CdS-sensitized DTTO electrodes and improve the efficiency of charge separation in CdS-sensitized QDSSCs, copper indium disulfide (CuInS2) is selected to cosensitize the DTTO electrodes with CdS, which has a complementary property of light absorption with CdS. The PCEs of QDSSCs based on these prepared QD-sensitized DTTO electrodes are measured. Our experimental results show that compared to those based on the CdS/DTTO electrodes without CuInS2, the PCEs of the QDSSCs based on CdS/CuInS2-sensitized DTTO electrode are significantly improved, which is mainly attributed to the increased light absorption and reduced charge recombination. Under simulated one-sun illumination, the best PCE of 1.42% is achieved for the QDSSCs based on CdS(10)/CuInS2/DTTO electrode, which is much higher than that (0.56%) of the QDSSCs based on CdS(10)/DTTO electrode.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Background
Quantum dots-sensitized solar cells (QDSSCs) for converting solar energy directly to electricity have been attracting extensive interest for potential photovoltaic application [1–4]. In QDSSCs, the TiO2 is widely used as the working electrode due to its non toxicity, high stability, wide availability, and good electronic properties. However, it is known that the TiO2 mainly absorbs the ultraviolet light due to its large band gap of 3.2 eV. Therefore, various types of quantum dots (QDs) with different optical absorption properties, such as CdS [5–7], CdTe [8–10], CdSe [4, 11–14], PbS [15, 16], PbSe [17], and CuInS2 [3, 18], have been synthesized to sensitize the TiO2 in order to extend the light absorption of the TiO2 into the visible region. To further increase the light absorption of QD-sensitized TiO2, increasing the loading amount of QDs through the improvement of the TiO2 photoelectrode structures is an effective way. Recently, a novel electrode structure, i.e., double-sided transparent TiO2 nanotube/ITO (DTTO) photoelectrodes were successfully fabricated by our group to enhance light absorption of CdS QD-sensitized TiO2 photoelectrodes mainly due to the increase of CdS deposition amount [19], in which the TiO2 nanotube arrays are fabricated on the double-sided transparent ITO substrates. However, for these CdS QD-sensitized DTTO (CdS/DTTO) photoelectrodes, there is still a room for further improvement in light absorption capacity because the CdS/DTTO photoelectrodes mainly absorb visible light with wavelengths less than 550 nm [19]. Hence, for the CdS/DTTO photoelectrodes, there is a prevailing need to find a suitable semiconductor material with a lower band gap than that (2.4 eV) of CdS to harvest more light with wavelengths longer than 550 nm. Copper indium disulfide (CuInS2) with a narrow band gap of about 1.6 eV is used as the absorption materials in solar cells from its excellent electric and optical properties [3]. Our previous work has shown that the CuInS2 can be used as a co-sensitizer to extend the spectral response of CdS-sensitized TiO2 nanotubes (TNTs) on the Ti substrate into the 500–700 nm wavelength region [18]. Moreover, it has also found that the CuInS2 can reduce the charge recombination in CdS/CuInS2-sensitized TNTs/Ti electrode. Nevertheless, there is still an issue to be resolved. Due to the opaque Ti substrate, only the QDs deposited on one side of the TNTs/Ti electrode can absorb the sunlight. Obviously, the light-harvesting ability of the opaque TNTs/Ti photoelectrode should be weaker than that of the DTTO photoelectrode.
In this study, we expand our previous work [18, 19]. Considering the advantage of the DTTO photoelectrode in the light-harvesting ability and the complementary effect of CdS and CuInS2 on the light absorption, the CdS/CuInS2-co-sensitized DTTO photoelectrodes are prepared for the QDSSCs. The detailed synthetic strategy is illustrated in Fig. 1. The surface morphology, optical, and photoelectrochemical properties of as-prepared CdS/CuInS2/DTTO photoelectrodes are systematically studied. The obtained experimental results demonstrate that, compared to the CdS/DTTO photoelectrodes, the light absorption abilities and photoelectrochemical activities of the CdS/CuInS2/DTTO photoelectrodes are increased and the power conversion efficiencies (PCEs) of the QDSSCs based on the CdS/CuInS2/DTTO photoelectrodes are significantly enhanced.
Methods
Materials
Indium tin oxide (ITO, ≤15 Ω/∀) sheet glass, titanium foil (Ti, Sigma-Aldrich, 0.25-mm thickness, 99.7% purity), ammonium fluoride (NH4F, Sigma-Aldrich, 98 + %), ethylene glycol (Junsei Chemical Co, 99.0%), cadmium chloride (CdCl2, Kanto Chemical Co, 98.0%), indium choride (InCl3, Sigma-Aldrich, 99.999%), sodium sulfide nonahydrate (Na2S, Sigma-Aldrich, 98.0%), cupric chloride (CuCl2, Junsei Chemical co., Ltd, >97.0 + %), and Ti(OCH2CH2CH2CH3)4 (Ti(OBu)4, Sigma-Aldrich, 97%). All the materials were used directly without further purification.
Synthesis of Double-Sided Transparent TNT/ITO Films
The TiO2 nanotube arrays (TNTs) were prepared by electrochemical anodization of the Ti foils. First, the electrolyte consisting of 0.5 wt% NH4F and 1.5 wt% distilled (DI) water in ethylene glycol (EG) was prepared. Before use, the electrolyte was stirred for 3 h at room temperature. After that, the cleaned Ti foils were anodized at a constant potential of 60 V in prepared electrolyte for 5 h in a two-electrode configuration with a platinum cathode [18]. Then, the formed TNTs were detached from the Ti substrate by intense ultrasonication in DI water. After that, the detached TNTs were adhered onto both sides of ITO glass with a drop of TiO2 sol. The process for the preparation of TiO2 sol containing Ti(OBu)4 and polyethylene glycol has been described in our previous work [19]. Finally, the as-prepared films were annealed at 450 °C for 2 h in air to crystallize the TiO2 tubes, after which the samples were naturally cooled down to room temperature to obtain the double-sided transparent TNT/ITO films (i.e., DTTO films).
Synthesis of CdS/DTTO and CdS/CuInS2/DTTO Electrodes
CdS and CuInS2 QDs were deposited on the TNTs by CBD method and SILAR progress, respectively, as described in our previous papers [18, 20]. The CuInS2 was first deposited on the DTTO films by SILAR progress. The precursors are a 5 mM InCl3 aqueous solution, a 5 mM CuCl2 aqueous solution, and a 50 mM Na2S aqueous solution. The detailed one-cycle synthesis of CuInS2 can be obtained from previous publication [18]. In this study, the SILAR cycle was repeated two times.
CdS QDs were deposited on the DTTO and CuInS2/DTTO electrodes by CBD method. The precursors are a 50 mM Na2S aqueous solution and a 50 mM CdCl2 aqueous solution. The electrode was first dipped into 50 mM Na2S aqueous solution for 1 min, and then rinsed with DI water. After that, the electrode was dipped into 50 mM CdCl2 aqueous solution for another 1 min, and then rinsed again with DI water. Such a soaking and cleaning process is a typical CBD cycle of CdS deposition. The DTTO and CuInS2/DTTO electrodes after n cycles of CdS deposition are denoted as CdS(n)/DTTO and CdS(n)/CuInS2/DTTO, respectively.
Characterization
The SEM images were recorded on a field-emission scanning electron microscopy (FESEM, FEI, Nova230). UV–vis absorption spectra were recorded using a UV–vis spectrophotometer (UV-2550, Shimadzu Corporation, Kyoto, Japan). Transmission electron microscope (TEM) analysis was done on a Tecnai G2 F30 TEM (FEI Company). Photoelectrochemical reactions of as-prepared samples were carried out in a 250-mL quartz cell, using a two-electrode configuration with the as-prepared samples as working electrode and a Pt counter electrode. A 3-m double-sided adhesive tape sandwiched between the work electrode and the Pt electrode is used to fix the distance between these two electrodes. The photocurrent–voltage characteristics of as-prepared samples with an effective surface area of 0.1 cm−2 were recorded using an electrochemical workstation (CHI660E, Shanghai Chenhua Instruments Co., Ltd., Shanghai, China) under simulated AM 1.5G illumination (100 mW cm−2) provided by a solar simulator equipped with a 500 W Xe lamp. The electrolyte was 1.0 M Na2S aqueous solution.
Results and Discussion
Figure 2a, b shows the top-view SEM image of prepared DTTO film and the cross-section SEM image of the detached TNTs from Ti substrate, respectively. As shown in Fig. 2a, the highly ordered TNTs with an average inner diameter of ~100 nm and a wall thickness of ~20 nm are formed. From Fig. 2b, the TNTs with a length up to about 30 μm can be observed. Figure 2c displays the top-view image of the CuInS2/DTTO film. It can be observed from Fig. 2c that some CuInS2 nanoparticles were dispersed on the surface of CuInS2/DTTO film. Moreover, compared to the TiO2 nanotube in the DTTO film, the inner diameter of CuInS2/TiO2 nanotube decreased slightly due to the deposition of CuInS2. Figure 2d displays a SEM image of one single CuInS2/TiO2 nanotube. It can be seen that the CuInS2 nanoparticles are deposited on the surface of the nanotube and form a CuInS2 thin film, which is consistent with the reported results [21]. By comparing the inner diameters of TiO2 nanotube and CuInS2/TiO2 nanotube, it can be obtained that the thickness of the CuInS2 thin film is about 10 nm. Figure 2e, f shows the top-view images of the CdS(10)/CuInS2/DTTO and CdS(15)/CuInS2/DTTO films, respectively. For both films, it can be clearly seen that CdS QDs have been deposited on the TNTs. Furthermore, by comparing Fig. 2e with Fig. 2f, it can be found that more CdS QDs are deposited onto the surface of the CdS(15)/CuInS2/DTTO film after 15 CBD cycles, indicating that the deposition amount of CdS QDs increases with the cycle number n.
Figure 3a, b shows the low- and high-magnification TEM images of the CdS(5)/CuInS2/DTTO film, respectively. As shown in Fig. 3a, b, the CdS QDs deposited onto the inner wall of the TiO2 tube are observed. The average size of the CdS QDs is about 10 nm. Moreover, as shown in the inset of Fig. 3a, the parallel lattice fringes in the wall of CuInS2/TiO2 nanotube are observed. After careful measurement, the interplanar spacing of these lattice fringes is 1.06 nm, corresponding to the (001) plane of tetragonal CuInS2 (JCPDS 38-0777). The inset of Fig. 3b shows a high-resolution transmission electron microscopy (HRTEM) image of the CdS QDs in the nanotube. The measured lattice spacing for observed fringes is 0.357 nm, which corresponds to the (100) lattice planes of hexagonal CdS (JCPDS 80-0006).
Figure 4a shows the UV–vis spectra of the DTTO, CuInS2/DTTO, CdS(n)/CuInS2/DTTO films (n = 5, 10, and 15). It can be seen that DTTO film absorbs the light with wavelengths less than 400 nm due to the wide bandgap of TiO2 (3.0 eV). While CuInS2 are deposited, the absorption spectrum of the CuInS2/DTTO film is extended from 400 to 700 nm, which is consistent with the previous result [18]. Compared to the CuInS2/DTTO film, the absorbance of the spectra of the CdS(n)/CuInS2/DTTO film significantly increases in the 375–515 nm wavelength region, which can be attributed to the light absorption of CdS. Furthermore, the absorbance of the CdS(n)/CuInS2/DTTO increases with an increase in CBD cycles, which is mainly due to the increased deposition amount of CdS. These results are similar to those reported in CdS-sentized TNTs [20, 22]. To further investigate the effect of the CuInS2 on the CdS/DTTO film, the absorption spectra of the CdS(n)/DTTO and CdS(n)/CuInS2/DTTO films were measured and compared. As an example, Fig. 4b shows the absorption spectrum of the CdS(5)/DTTO and CdS(5)/CuInS2/DTTO films, which clearly displays that the absorbance of the spectra of the CdS(5)/CuInS2/DTTO film are enhanced compared with the CdS(5)/DTTO film. In particular, the deposited CuInS2 significantly extended the response of the CdS(5)/DTTO into the 500–700 nm wavelength region [22], confirming that the CuInS2 layer can effectively improve the light absorption property of the CdS/DTTO films.
Figure 5 shows the J–V characteristics of the QDSSCs based on prepared CdS(n)/DTTO and CdS(n)/CuInS2/DTTO electrodes under illumination (n = 5, 10, and 15). Four performance parameters for the measured QDSSCs, open-circuit voltage (V oc), short-circuit photocurrent (J sc), fill factor (FF), and PCE, have been shown in Table 1.
For the cells based on the CdS(n)/DTTO electrodes, the parameters J sc and PCE are increased with the increase of cycle number n from 5 to 10 and decreased with the further increase of n from 10 to 15. On increasing n from 5 to 15, the J sc first increases to 4.35 and then decreases to 3.9 mA cm−2. This highest J sc (i.e., 4.35 mA cm−2) is higher than that of CdS-sensitized TiO2 nanorod electrode for QDSSCs [23]. Similarly, the PCE first increases from 0.47 to 0.65% and then decreases to 0.56%. The highest PCE of 0.65% is achieved for the cell based on the CdS(10)/DTTO electrode. Moreover, the effects of the cycle number n on the values of both V oc and FF are not obvious. These results may be explained as follows: As shown in Fig. 4, the amount of CdS loading increases with the increase of n from 5 to 10, which helps to strengthen the light absorption and therefore increase the photocurrent. However, as the cycle number n increased further (n > 10), the electron-transfer resistance in deposited CdS QDs becomes greater as the loading amount of CdS increases (Fig. 2f) and therefore leads to a more serious charge recombination between the photo-generated electrons in CdS and the redox ions in the electrolyte. Therefore, the J sc, V oc, and FF may decrease with the further deposition of CdS although the light absorption increases.
For the cells based on the CdS(n)/CuInS2/DTTO electrodes with CuInS2 thin film, it can be seen from Fig. 5 that the effect of the cycle number n on V oc is also not obvious. However, the V oc of the cell based on the CdS(n)/CuInS2/DTTO electrode is significantly higher than that of the cell based on the CdS(n)/DTTO electrode, indicating that the CuInS2 can effectively reduce the charge recombination. The parameters J sc, FF, and PCE first increase and then decrease with the increase of n from 5 to 15. On increasing n from 5 to 10, the J sc increases from 4.6 to 5.18 mA cm−2, while FF increases from 0.32 to 0.38. As n increases further from 10 to 15, the J sc and FF decrease to 5.01 mA cm−2 and 0.33, respectively. Compared to the cells based on the CdS(n)/DTTO electrodes, for a certain cycle n, all four parameters V oc, J sc, FF, and PCE of the cells based on the CdS(n)/CuInS2/DTTO electrodes are improved. As shown in Table 1, the highest PCE of 1.42% is obtained for the cell based on the CdS(10)/CuInS2/DTTO electrode, which is 2.2 times than that (0.65%) of the cell based on the CdS(10)/ DTTO electrode. Apparently, the PCEs of the cells based on the CdS(n)/CuInS2/DTTO electrodes have been enhanced largely by the CuInS2 layer. On one hand, as shown in Fig. 4, optical absorption of the CdS(n)/CuInS2/DTTO electrodes was improved in the wavelengths greater than 500 nm compared to the CdS(n)/DTTO electrodes, which would lead to an increased photocurrent. On the other hand, the charge recombination may be reduced through the deposited CuInS2. For the purpose of facilitating discussion, Fig. 6 shows the energy diagram of the CdS/CuInS2/DTTO electrode. As shown in Fig. 6, the conduction energy level of CuInS2 lies between that of CdS and that of TiO2, which suggests that the photo-generated electrons in CdS can be easily injected into the TiO2 through the CuInS2 layer. At the same time, it is difficult for the injected electrons in TiO2 to recombine with redox ions in the electrolyte because there exists an energy barrier at the interface between the TiO2 and CuInS2, which leads to a reduced charge recombination in the CdS(n)/CuInS2/DTTO electrodes and therefore enhances the V oc, J sc, and FF.
Conclusions
In conclusion, the CdS/CuInS2 quantum dots-sensitized double-sided transparent TiO2 nanotube electrodes are fabricated for the QDSSCs. Our experimental results showed that the deposited CuInS2 enhanced the light absorption of the CdS/DTTO electrodes and reduced the charge recombination in the QDSSCs. These two factors resulted in improved photovoltaic performance of the QDSSCs based on the CdS(n)/CuInS2/DTTO electrodes.
Abbreviations
- DTTO:
-
Double-sided transparent TNT/ITO
- FF:
-
Fill factor
- J sc :
-
Short-circuit photocurrent
- PCEs:
-
Power conversion efficiencies
- QDs:
-
Quantum dots
- QDSSCs:
-
Quantum dots-sensitized solar cells
- TNT:
-
TiO2 nanotube
- V oc :
-
Open-circuit voltage
References
Kamat PV (2008) Quantum dot solar cells. Semiconductor nanocrystals as light harvesters. J Phys Chem C 112:18737–18753
Guenes S, Sariciftci NS (2008) Hybrid solar cells. Inorg Chim Acta 361:581–588
Han M, Jia J, Wang W (2016) Pulsed laser deposition of Bi2S3/CuInS2/TiO2 cascade structure for high photoelectrochemical performance. RSC Adv 6:70952–70959
Zhang B, Zheng J, Li X, Fang Y, Wang LW, Lin Y, Pan F (2016) Tuning band alignment by CdS layers using a SILAR method to enhance TiO2/CdS/CdSe quantum-dot solar-cell performance. Chem Commun 52:5706–5709
Prabakar K, Seo H, Son M, Kim H (2009) CdS quantum dots sensitized TiO2 photoelectrodes. Mater Chem Phys 117:26–28
Lee JC, Kim TG, Lee W, Han SH, Sung YM (2009) Growth of CdS nanorod-coated TiO2 nanowires on conductive glass for photovoltaic applications. Cryst Growth Des 9:4519–4523
Chen C, Zhai Y, Li F, Ling L (2015) Photocurrent enhancement of the CdS/TiO2/ITO photoelectrodes achieved by controlling the deposition amount of Ag2S nanocrystals. Appl Surf Sci 356:574–580
Gao XF, Li HB, Sun WT, Chen Q, Tang FQ, Peng LM (2009) CdTe quantum dots-sensitized TiO2 nanotube array photoelectrodes. J Phys Chem C 113:7531–7535
Lee HJ, Kim DY, Yoo JS, Bang J, Kim S, Park SM (2007) Anchoring cadmium chalcogenide quantum dots (QDs) onto stable oxide semiconductors for QD sensitized solar cells. B Kor Chem Soc 28:953–958
Seabold JA, Shankar K, Wilke RHT, Paulose M, Varghese OK, Grimes CA, Choi KS (2008) Photoelectrochemical properties of heterojunction CdTe/TiO2 electrodes constructed using highly ordered TiO2 nanotube arrays. Chem Mater 20:5266–5273
Kim JY, Choi SB, Noh JH, HunYoon S, Lee S, Noh TH, Frank AJ, Hong KS (2009) Synthesis of CdSe-TiO2 nanocomposites and their applications to TiO2 sensitized solar cells. Langmuir 25:5348–5351
Fan SQ, Kim D, Kim JJ, Jung DW, Kang SO, Ko J (2009) Highly efficient CdSe quantum-dot-sensitized TiO2 photoelectrodes for solar cell applications. Electrochem Commun 11:1337–1339
Shen Q, Arae D, Toyoda T (2004) Photosensitization of nanostructured TiO2 with CdSe quantum dots: effects of microstructure and electron transport in TiO2 substrates. J Photochem Photobiol 164:75–80
Yun HJ, Paik T, Diroll B, Edley ME, Baxter JB, Murray CB (2016) Nanocrystal size-dependent efficiency of quantum dot sensitized solar cells in the strongly coupled CdSe nanocrystals/TiO2 system. ACS Appl Mater Interfaces 8:14692–14700
Lee H, Leventis HC, Moon SJ, Chen P, Ito S, Haque SA, Torres T, Nuesch F, Geiger T, Zakeeruddin SM, Gratzel M, Nazeeruddin MK (2009) PbS and US quantum dot-sensitized solid-state solar cells: “old concepts, new results”. Adv Funct Mater 19:2735–2742
Hoyer P, Konenkamp R (1995) Photoconduction in porous TiO2 sensitized by Pbs quantum dots. Appl Phys Lett 66:349–351
Tvrdy K, Kamat PV (2009) Substrate driven photochemistry of CdSe quantum dot films: charge injection and irreversible transformations on oxide surfaces. J Phys Chem A 113:3765–3772
Chen C, Ali G, Yoo SH, Kum JM, Cho SO (2011) Improved conversion efficiency of CdS quantum dot-sensitized TiO2 nanotube-arrays using CuInS2 as a co-sensitizer and an energy barrier layer. J Mater Chem 21:16430–16435
Chen C, Li FM, Li GQ, Tan FR, Li SJ, Ling LY (2014) Double-sided transparent electrodes of TiO2 nanotube arrays for highly efficient CdS quantum dot-sensitized photoelectrodes. J Mater Sci 49:1868–1874
Chen C, Xie Y, Ali G, Yoo SH, Cho SO (2011) Improved conversion efficiency of CdS quantum dots-sensitized TiO2 nanotube array using ZnO energy barrier layer. Nanotechnology 22:015202
Chang HY, Tzeng WJ, Cheng SY (2009) Modification of TiO2 nanotube arrays by solution coating. Solid State Ionics 180:817–821
Li TL, Lee YL, Teng HS (2011) CuInS2 quantum dots coated with CdS as high-performance sensitizers for TiO2 electrodes in photoelectrochemical cells. J Mater Chem 21:5089–5098
Wan J, Rong L, Tong Y, Chen S, Hu Y, Wang B, Yang X, Hao W (2016) Hydrothermal etching treatment to rutile TiO2 nanorod arrays for improving the efficiency of CdS-sensitized TiO2 solar cells. Nanoscale Res Lett 11:1–9
Acknowledgements
We gratefully acknowledge Dr. Guoqiang Li and Dr. Furui Tan for the permission to use the optical measurement system.
Funding
This work was mainly supported by Henan University Distinguished Professor Startup Fund, National Natural Science Foundation of China-Talent Training Fund of Henan (U1404616), Seed Fund of Young Scientific Research Talents of Henan University (CX0000A40540), and Research Fund of Henan University (2013YBZR046).
Authors’ Contributions
CC carried out the experiments, participated in the sequence alignment, and drafted the manuscript. FL participated in the device preparation and performed the statistical analysis. LL helped to draft the manuscript. All authors read and approved the final manuscript.
Competing Interests
The authors declare that they have no competing interests.
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Chen, C., Ling, L. & Li, F. Double-Sided Transparent TiO2 Nanotube/ITO Electrodes for Efficient CdS/CuInS2 Quantum Dot-Sensitized Solar Cells. Nanoscale Res Lett 12, 4 (2017). https://doi.org/10.1186/s11671-016-1787-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s11671-016-1787-9