Abstract
The strength and mechanism of destruction are studied for low-alloy steel 09G2S subjected to a combined treatment using an extrusion and screw pressing (ESP) of bulk billets at room temperature and at a temperature of 213 K. Data concerning the mechanical properties of steel at room temperature and 213 K in the initial state and state after ESP are given. The mechanism of destruction of steel 09G2S in different states is described.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Ivanova, V.S. and Gordienko, L.K., Novye puti povysheniya prochnosti metallov (New Approaches to Improve Durability of Metals), Moscow: Nauka, 1964.
Gulyaev, A.P., Structural changes occurring during thermomechanical treatment of steel and their influence on the mechanical properties, Met. Sci. Heat Treat., 1966, vol. 7, no. 11, pp. 709–717.
Bernshtein, M.L., Termomekhanicheskaya obrabotka metallov i splavov (Thermochemical Processing of Metals and Alloys), Moscow: Metallurgiya, 1968, vol.1.
Grigor’ev, A.K. and Kodzhaspirov, G.E., Termomekhanicheskoe uprochnenie stali v zagotovitel’nom proizvodstve (Thermomechanical Strengthening of Steel in Production of Billets), Moscow: Mashinostroenie, 1985.
Bridgman, P.W., Studies in Large Plastic Flow and Fracture: With Special Emphasis on the Effects of Hydrostatic Pressure, New York: McGraw-Hill, 1952.
Segal, V.M., Reznikov, V.I., Kopylov, V.I., Pavlik, D.A., and Malyshev, V.F., Plastic Structuring of Metals, Minsk: Navuka i Tekhnika, 1994.
Valiev, R.Z. and Aleksandrov, I.V., Nanostrukturnye materialy, poluchennye intensivnoi plasticheskoi deformatsiei (Nanomaterials Obtained by Intensive Plastic Deformation), Moscow: Logos, 2000.
Salishchev, G.A., Valiakhmetov, O.R., and Galeyev, R.M., Formation of submicrocrystalline structure in the titanium alloy VT8 and its influence on mechanical properties, J. Mater. Sci., 1993, vol. 28, no. 11, pp. 2898–2902.
Zhu, Y.T., Jiang, H., Huang, J., and Lowe, T.C., A new route to bulk nanostructured metals, Metall. Mater. Trans. A, 2001, vol. 32, pp. 1559–1562.
Sastry, Sh.M.L., Dobatkin, S.V., and Sidorova, S.V., Formation of a submicrocrystalline structure in 10G2FT steel upon equal-channel angular pressing followed by heating, Russ. Metall. (Engl. Transl.), 2004, vol. 2004, no. 2, pp. 129–134.
Lotkov, A.I., Grishkov, V.N., Dudarev, E.F., Girsova, N.V., and Tabachenko, A.N., Ultrafine grained structure, martensite transformations and inelastic properties of titanium nickelide after abc pressing, Vopr. Materialoved., 2008, no. 1 (53), pp. 161–165.
Stolyarov, V.V., Features of deformation behavior at rolling and tension under current in TiNi alloy, Rev. Adv. Mater. Sci., 2010, vol. 25, pp. 194–202.
Li, L. and Virta, J., Ultrahigh strength steel wires processed by severe plastic deformation for ultrafine grained microstructure, Met. Sci. Heat Treat., 2011, vol. 27, no. 5, pp. 845–862.
Maier, G.G., Astafurova, E.G., Maier, H.J., et al., Annealing behavior of ultrafine grained structure in low-carbon steel produced by equal channel angular pressing, Mater. Sci. Eng., A, 2013, vol. 581, no. 1, pp. 104–107.
Donic, T., Martikán, M., and Hadzima, B., New unique ECAP system with ultrasound and backpressure, IOP Conf. Ser.: Mater. Sci. Eng., 2014, vol. 63, no. 1, art. ID 012047. https://doi.org/iopscience.iop.org/1757-899X/63/1/012047.
Park, K.-T., Park, L., Kim, H.J., Kim, S.B., and Lee, C.S., Analysis on dynamic tensile extrusion behavior of UFG OFHC Cu, IOP Conf. Ser.: Mater. Sci. Eng., 2014, vol. 63, no. 1, art. ID 012144. https://doi.org/iopscience.iop.org/1757-899X/63/1/012144.
Beigel’zimer, Ya.E., Varyukhin, V.N., Orlov, D.V., and Synkov, S.G., Vintovaya ekstruziya—protsess nakopleniya deformatsii (Screw Extrusion as the Process of Accumulation of Deformations), Donetsk: TEAN, 2003.
Ivanov, A.M., The combination of thermoplastic methods in steel processing, Fundam. Prikl. Probl. Tekh. Tekhnol., 2012, no. 2–4 (292), pp. 25–33.
Ivanov, A.M., Syromyatnikova, A.S., and Petrova, N.D., Strengthening by intensive plastic deformation and destruction of structural steel, Uprochnyayushchie Tekhnol. Pokrytiya, 2012, no. 3, pp. 39–42.
Ivanov, A.M., Petrova, N.D., and Lepov, V.V., Effect of extrusion and screw pressing on the structure and mechanical properties of low-alloy steel, Nauka Obraz., 2015, no. 4 (80), pp. 87–90.
Ivanov, A.M., Mechanical properties, patterns of deformation, and the destruction mechanism of superinvar under deformation processing by a combined method, Perspekt. Mater., 2017, no. 9, pp. 72–80.
Serebryanyi, V.N. and Dobatkin, S.V., Improvement of plasticity and deformability of magnesium alloys by intensive plastic deformation. Part 1: Influence of the structure. A review, Materialovedenie, 2013, no. 12, pp. 13–26.
Serebryanyi, V.N. and Dobatkin, S.V., Improvement of plasticity and deformability of magnesium alloys by intensive plastic deformation. Part 2. Influence of the texture. A review, Materialovedenie, 2015, no. 11, pp. 9–22.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © A.M. Ivanov, 2018, published in Materialovedenie, 2018, No. 2, pp. 13–17.
Rights and permissions
About this article
Cite this article
Ivanov, A.M. Strength and Destruction Mechanism of Low-Alloy Steel Subjected to a Combined Deformation Treatment. Inorg. Mater. Appl. Res. 9, 741–745 (2018). https://doi.org/10.1134/S2075113318040135
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1134/S2075113318040135