Abstract
The effects of velocity and gas type on foam flow through porous media have yet to be completely elucidated. Pressure drop and capillary pressure measurements were made at ambient conditions during a series of foam quality scan experiments in a homogenous sandpack while foam texture was simultaneously visualized. New insights into foam-flow behavior in porous media were discovered. Previously accepted “limiting” capillary pressure theory is challenged by the findings in this work, and the “limiting” terminology is replaced with the word “plateau” to reflect these novel observations. Plateau capillary pressure \({(P}_{c})\) and transition foam quality were found to increase with velocity. Transition foam quality was found to depend mostly on liquid velocity rather than gas velocity and is physically linked to foam type (continuous vs. discontinuous) and texture (fine vs. coarse). Distinct rheological behaviors also arose in the low- and high-quality foam regimes as a function of velocity. Foam flow was found to be strongly shear thinning in the low-quality regime where foam texture was fine and discontinuous. In the high-quality regime, the rheology was weakly shear thinning to Newtonian for coarsely textured foam and continuous-gas flow respectively. When all other variables were held constant, at ambient conditions, CO2 foam was found to be weaker with also lower capillary pressures than N2 foam and the differences in gas solubility is a likely explanation.
Similar content being viewed by others
Introduction
Foams have numerous promising applications in porous media ranging from enhanced oil recovery to CO2 storage in geologic formations1,2,3,4. A growing body of literature is dedicated to understanding the complexities of foam flow in porous media. The prediction of pressure gradient and liquid saturations for a given foam-flow system for a set of flow conditions is a general, yet elusive, goal in this field. The challenge lies in the complex interplay among relevant variables such as surfactant formulation, porous media type, and non-aqueous phase type.
Because the interactions among these variables are complex, fundamental studies are needed to deduce the true nature of foam in porous media and to identify it by simplifying relationships among the pertinent variables. One such study by Khatib and colleagues provided evidence for a “limiting” capillary pressure5. This theory greatly simplified foam models, as the capillary pressure could essentially remain a fixed variable. Another study by Hirasaki and Lawson laid the groundwork for predicting apparent viscosities of foams in porous media via a capillary tube model6. Falls et al. later extended these relationships to complex porous media with converging–diverging geometries7. In a separate work, Falls and colleagues clearly identified pertinent aspects of the shape and size of foam bubbles and related these features to mechanisms resulting in creation or destruction of bubbles8. Rossen identified a minimum pressure gradient required to mobilize foam9,10. Osterloh and Jante also clearly laid out the regimes in which foam flow becomes independent of either the gas or the liquid velocity11. Kam and Rossen identified the multiple steady states of certain foams12. Other works have explored the effects of relevant variables such as surfactant type and concentration13,14,15,16,17, salinity17,18, porous media heterogeneity19, porous media permeability20,21, and gas type22,23,24. These studies and others have significantly advanced understanding of foam flow in porous media, but predictive modeling capabilities have yet to be achieved25,26.
The aim of the present study is to further improve understanding of foam flow in porous media by examining fundamental relationships among capillary pressure, pressure gradient, apparent viscosity, and foam texture in a simple foam flow system that can be compared with several others from the literature5,11,16,27,28. To accomplish this, a large body of data was collected during foam quality scan experiments conducted at fixed gas velocities, in the style of Khatib et al.5, during which pre-generated foam was injected into a high-permeability sandpack and capillary pressure was measured via probe while in-situ observations of the foam were made.
Materials and methods
Chemicals and porous media
The surfactant selected for the study was Alpha olefin sulfonate AOS14-16 (activity = 39.03 wt%, Lot#7653919, Stepan®). A fresh solution of 1 wt% AOS14–16 was prepared with 3 wt% NaCl in Milli-Q® ultrapure water for each foam-flow test. Dry N2 gas (Airgas, 99.999% purity) and Bone-Dry CO2 gas (Airgas, 99.999% purity) were supplied by Matheson.
Properties of the sand pack and foam pre-generators for foam-flooding system testing are summarized in Table 1. The main body of the sand pack was constructed from a transparent polycarbonate tube with grooved rubber stoppers compressed into both ends. Rubber O-rings and two metal screens contained the sand in the tube. A metal compression cage prevented fluid leaks around the stoppers and ensured the sand remained in place. A capillary pressure probe was installed half-way down the length of the sand pack and was sealed into the main body by a rubber stopper with a silicone-gasket plug. The overall pressure drop across the sand pack was measured with a differential pressure transducer (Validyne). Further details of the pack construction are given in Vavra et al.29.
Foam quality scan experimental procedure at fixed gas flow rate
Foam quality scan protocol
For all experiments, foam quality scans were conducted with constant gas-volumetric flow rates defined at standard conditions. Liquid flow rates varied to change the foam quality given by:
where \({f}_{g}\) is foam quality, \({q}_{g}\)[cm3/s] is evaluated at average-pressure and solubility-compensated gas volumetric flow rate at the midpoint of the pack, and \({q}_{l}\) [cm3/s] is liquid volumetric flow rate. The outlet of the sand pack was assumed to be at atmospheric pressure. The pressure-compensated flow rate, \({q}_{g}^{pressure-compensated}\), was calculated at the mid-length of the pack, where the capillary pressure probe was located, with the following formula:
where \({q}_{g}^{inlet}\) [cm3/s] and \({q}_{g}^{outlet}\) [cm3/s] are the volumetric gas flow rates at the inlet and outlet of the sand pack respectively, \({P}^{outlet}\) [psi] is atmospheric pressure at laboratory conditions, and \(\Delta P\) [psi] is the pressure drop across the sand pack at steady-state. The solubility of CO2 for relevant average pressures was estimated and flow rates were corrected appropriately.
The gas and the aqueous phases were co-injected through a foam pre-generator before entering the sand pack, and the surfactant solution was recycled for each test. All tests were conducted from high-to-low foam quality. N2 gas was injected with flow rates defined at standard conditions of 1 cc/min, 3 cc/min, 9 cc/min, and 18 cc/min corresponding to standard superficial velocities of 2.3 ft/day (8.2 × 10–6 m/s), 7 ft/day (2.5 × 10–5 m/s), 21 ft/day (7.4 × 10–5 m/s), and 42 ft/day (14.8 × 10–5 m/s) respectively. CO2 gas was injected at standard conditions with a flow rate of 11.4 cc/min corresponding to a standard superficial velocity of 26.6 ft/day (9.4 × 10–5 m/s). A capillary pressure probe was sealed into the sand pack 5.6 in (14.25 cm) from the inlet. Details of the probe construction and static validation are provided in Vavra et al.29 Specifics of experimental conditions are given in Table 2.
Pressure measurement and apparent viscosity
Capillary pressure and overall pressure drop were recorded by software every 5 s and averaged over a minimum of 0.25 PV of total injection at each flow condition. The temporal standard deviation was calculated. The apparent viscosity \({\mu }_{app}\) was then calculated from Darcy’s law assuming pseudo-single-phase flow:
where \({\mu }_{app}\) [cP] is apparent viscosity, \(k\) [D] is absolute permeability, A [cm2] is the cross-sectional area of the sand pack, \(\Delta P\) [atm] is the overall pressure drop, and \(L\) [cm] is the length of the sand pack.
In-situ foam texture visualization
The texture of the foam flowing was filmed through the transparent wall of the sand-pack holder through a microscope objective. The visualized location was at the midpoint of the pack at the same distance from the inlet where the probe was located. The “footprint” of the foam directly contacting the wall was filmed at a resolution of 3080 × 1260 at 60 fps and 1290 × 1080 at 240 fps. LED ring lights were placed on the top, bottom, and side of the pack. This lighting configuration allowed for reflections in the plateau borders, where the foam contacted the inside wall of the polycarbonate sand-pack holder, to be visualized. The permeability at the wall of the pack is somewhat higher than that deeper into its center.
Results and discussion
Effect of gas flow rate on foam flow: capillary pressure, pressure gradient, apparent viscosity, and transition foam quality
Capillary pressure in-situ foam observations
The trends presented in Fig. 1 partially concur with those found in the literature, but some findings are different from several widely accepted assumptions of foam flow in porous media. Vavra et al. measured capillary pressure and found it to plateau over a range of foam qualities at a fixed gas velocity29. This finding is seemingly in agreement with Khatib et al. who were the first to measure a plateau in capillary pressure5. They identified the plateau as a “limiting” capillary pressure where the number of lamellae existing in the sand pack was only controlled by coalescence rate while the effect of generation rate was unmentioned. One aspect of evidence given in favor of this assumption by Khatib et al. was that the “limiting” capillary pressure was observed to decrease from 0.55 psi to 0.47 psi with a 2.3 × increase in gas rate5. It was argued that greater mechanical stresses, associated with increasing the gas velocity, resulted in more lamella rupture and thus a lower limiting value for capillary pressure5. Jimenez and Radke also showed that moving lamella rupture easier than when stationary30. Later, Farajzadeh et al. stated “as the lamella velocity increases, the limiting capillary pressure must decrease to compensate for the increase in disjoining pressure as the lamella stretches in passing from a pore throat to a pore body”20. On the other hand, in Fig. 1a, the plateau value for capillary pressure, indicated by a horizontal dashed line, increases from 0.53 psi to 0.82, 1.02, and 1.14 psi with increases in gas flow rate with multiples of 3 ×, 9 ×, and 18 × over the initial 1 × flow rate respectively. This finding suggests, for the tested conditions, similar to the conditions tested by Khatib et al.5, the number of lamellae in the foam at the plateau value is not only a function of coalescence by lamellae rupture, but also a function of other foam creation and/or destruction mechanisms such as lamella division and Ostwald ripening. For example, as gas velocity increases, the rate of lamella rupture could be expected to increase for the aforementioned reasons; however, the rate of foam generation by lamella division might also increase. Hence the term “plateau” is chosen to describe the flattened portion of the capillary pressure curves in Fig. 1a instead of “limiting” implying coalescence by lamella rupture as the dominating mechanism preventing further increase in capillary pressure. Alvarez predicted the “limiting” capillary pressure to increase with liquid velocity31. A similar observation was made by Ouali et al. who estimated capillary pressure from gas saturations measured by CT and found the maximum value, referred to as “\({P}_{c}^{*}\)” despite the lack of a plateau, to increase with increasing total velocity32. In their work, an appreciable plateau in liquid saturation (or capillary pressure) over a substantial range of foam quality was absent, but a peak value was observed much like that found by Kibodeaux and Rossen as well as Føyen et al. for some conditions1,27,32.
Another aspect of this study in agreement with Ouali et al. was measured capillary pressure decreasing with increasing foam quality in the high-quality regime32. For all tested gas rates, the capillary pressure “collapses” above the transition foam quality and converges on the same value of approximately 0.3 psi. The decrease in capillary pressure was observed regardless of velocity implying that, at some transition foam quality, the capillary pressure will always decrease. This process corresponded with foam coarsening, and might occur at an extremely dry foam quality for some foaming systems depending on surfactant formulation, porous media, gas type, etc. This decrease in capillary pressure above \({f}_{g}\) = 0.98 was also observed by Kibodeaux and Rossen for a constant gas rate experiment despite their experiments being with a rock core rather than a sand pack27. Ouali et al. and Føyen et al. observed the decrease in capillary pressure at foam qualities around \({f}_{g}\) = 0.8.1,32
Experiments were conducted at a constant gas rate, but capillary pressure can be visualized in the style of Osterloh and Jante (as a function of the liquid and gas rate) in the contour plots of Fig. 2a and b11 (see Supplemental Video S1). In these plots, the magnitudes of capillary pressures correspond to colors. The points, indicated by circles or shapes, correspond to measurements made with the capillary pressure probe while all other information has been linearly interpolated. Figure 2a is to help in the visualization of capillary pressures for the entire variable space that was measured, and the roughly horizontal rows of points correspond to the various gas rates of the experiments (1 ×, 3 ×, 9 ×, and 18 ×). Figure 2b is plotted with a truncated liquid-rate axis, as found in the literature11,16,31, to better visualize the high-quality regime. Plotted in this way, for slow enough liquid velocities (less than approximately 10 ft/day), capillary pressure is relatively independent of the liquid rate in the low-quality regime where the plateau range occurs and, for fast enough gas velocities (greater than approximately 10 ft/day), relatively independent of the gas rate in the high-quality regime. The symbols indicate the foam type and texture that was observed in situ.
In-situ observations of foam texture and type
Foam texture (coarse vs. fine) and type (continuous vs. discontinuous) have been recognized as playing an important role in foam-flow behavior in porous media5,8,31,33,34. The “strongest” foams in terms of largest pressure gradients, lowest gas mobility, and highest capillary pressures are associated with fine (small bubble size) discontinuous (bubbles separated by lamellae) foams. “Weak” foams are either coarse (large bubble size) discontinuous foams or continuous-gas flow in which continuous gas channels flow through pockets of trapped discontinuous-gas foam pockets. Texture refers to bubble size and type refers to continuous vs. discontinuous gas. Fine foams exist in the low-quality regime. It has also been recognized that foam coarsens in the high-quality regime and becomes coarser with increasing foam quality35. Eventually, at dry enough foam qualities, the bubble size becomes on the order of the length scale of the porous medium, and a continuous-gas foam form. Note that the injection condition is not necessarily reflected in the saturation of the porous medium. In other words, a change in the fractional flow does not mean that there will be a corresponding change in the gas saturation. Fine foams at relatively low foam qualities lead to low gas mobility and low liquid saturations whereas coarse or continuous-gas flow at higher qualities is associated with higher gas mobilities and higher liquid saturations (Fig. 1a). In this study, foam flow states were categorized based on qualitative observations of the microscopy footage taken during foam-quality scan tests (see Supplemental Video S1). Foam flow was broadly categorized into four states given in the order in which the experiment was conducted:
-
1.
State I For the driest and slowest injection conditions, lamellae were essentially stationary during the time over which they were observed. This likely means that most of the gas was flowing as a continuous phase, and any foam that was present was trapped. This condition occurred in the high-quality regime during the 1 × and 3 × flow rate experiments.
-
2.
State II This state is similar to State I, but as injection conditions became wetter and liquid velocity increased, a steady-state “transition” foam type was observed where periodic lamellae movement occurred but was unsustained. This condition occurred in the high-quality regime and may be associated with periodic switching between continuous and discontinuous gas flow where most of the foam remains trapped.
-
3.
State III Another transition foam type occurred in the high-quality regime that involved flowing coarse foam. This foam flow state occurred over a narrow range of conditions and corresponds with a sharp transition in \({P}_{c}\)
-
4.
State IV In the low-quality regime, fine-foam flow was observed.
The in-situ observations, of these foam-flow states, help in explaining the measured trends in capillary pressure, pressure gradient, apparent viscosity as a function of foam quality, liquid velocity, and gas velocity.
Pressure gradient
Pressure gradient curves are given in Fig. 1b for each gas rate evaluated. Each curve is divided into two distinct slopes as marked by a vertical dashed line. The low-quality regime, at foam qualities below the transition foam quality, and the high-quality regime at foam qualities greater than the transition foam quality. The low- and high-quality regimes are analogous to the liquid- and gas-rate independent regimes respectively that were first identified by Osterloh and Jante11. The pressure gradient trend is relatively independent of foam quality in the low-quality regime because the liquid flow rate was changed while the mass flow for the gas flow rate was held constant. Overall, there is a slight positive dependence of pressure gradient on liquid flow rate in the low-quality regime as seen in Fig. 2c. Small changes in gas compressibility with changes in pressure drop could contribute to the slightly positive slope in pressure gradients in this regime. In the high-quality regime in Fig. 1b, pressure gradients decline with foam quality with the steepness of the decline growing sharper with increasing gas rate. As indicated by the symbols in Fig. 2d, this decline in pressure gradients is associated with a transition from a fine foam to a continuous-gas foam with various steady states of coarse foam in between.
Apparent viscosity as a function of gas velocity
For decreasing the liquid rate at a given gas velocity, the apparent viscosity first increased up to a peak before decreasing with increasing foam quality (Fig. 1c). This trend appears identical to that for experiments conducted with total flow velocity fixed36,37,38. This is confirmed by examining Fig. 2e and following the trend in apparent viscosity for a line of either fixed gas velocity (zero slope) or fixed total velocity (slope = − 1). The relatively high apparent viscosities reported here are in accord with the presence of a “strong” foam and the high permeability of the porous medium. The transition foam quality separating the high- and low-quality regimes in apparent viscosity always corresponded to that for the pressure gradient despite changing liquid velocities. In the low-quality regime, changes in the liquid velocity have minimal impact on the apparent viscosity. Conversely, in the high-quality regime, small changes in the liquid velocity led to large changes in apparent viscosity (Fig. 2f).
In the low-quality regime the apparent viscosity decreases with increasing gas velocity due to shear thinning (Fig. 1c). This occurs despite an increase in the plateau capillary pressure with gas velocity (Fig. 1a). Therefore, foam types at the capillary-pressure plateau are not necessarily synonymous with “strong” foam, in terms of high-apparent viscosity. Another way to conceptualize foam strength is in terms of gas relative permeability. The same foam flow condition can be “stronger” in terms of relative gas permeability (i.e. lower gas permeability leads to lower liquid saturation and higher capillary pressures) but simultaneously “weaker” in terms of relative apparent viscosity. In actuality, the foam flow conditions exhibiting higher capillary pressures are stronger. Also of note, in the high-quality regime, where foam states I, II, and III are present (Fig. 2b,d,f), the apparent viscosity curves overlap across all tested gas rates (Fig. 1c). The overlapping region of the curves in the high-quality regime is a linear function of fractional flow as indicated by the diagonal dashed line in Fig. 1c.
Transition foam quality
Transition foam quality has been assumed by some to be independent of total velocity16,39. This assumption is critical for modeling foam flow in porous media and for predicting appropriate injection conditions into a reservoir. In some studies, test results support this assumption5,40. In others, the invariance of transition foam quality with increasing velocity is less clear16,32,39. Osterloh and Jante identified the transition foam quality by eye as the line of constant foam quality roughly separating the gas-rate-independent high-quality regime from the liquid-rate-independent low-quality regime11. This protocol has been followed by others31. In the present study, the transition between low- and high-quality regimes was identified based on the change in slope of the pressure gradient trends and was found to depend on the flow rate (Fig. 1b,c). This assertion is evident when drawing a line connecting the transition points shown as a dashed-black line on Fig. 2b, d, and f. The lines failed to follow a constant foam quality (a straight line passing through the origin). The transition from the low-to-high- quality regime corresponds to the transition from a fine-to-coarse foam texture. Thus, the transition foam quality is found to be physically linked to flow-rate-dependent mechanisms of foam that control foam texture. The transition foam quality generally depends more on changes in the liquid velocity than those in the gas velocity. The findings of Kahrobaei et al. generally agree with this assessment in that, the transition between distinct rheological regimes in the foam was a function of only the liquid velocity16. One hypothesis is that, at low gas rates, most of the gas is flowing continuously (and/or as a coarse foam). With increasing gas flow rate, more stationary bubbles are mobilized and foam generation by lamella or bubble division occurs resulting in a higher transition foam quality. Other factors might be playing a role. The fraction of bubbles that are stationary at any given point in time was observed to decrease with increasing gas velocity at constant foam quality. Also, the rate of bubble coarsening by Ostwald ripening relative to the average rate of bubble translation could be significant.
Foam rheology
In assessing the rheology of foam flow in porous media, a log–log plot of apparent viscosity versus either total or gas superficial/interstitial velocity is commonly constructed for values of constant foam quality6,7,31,32,40. This plot has been constructed in Fig. 3 for both the high-quality and low-quality regimes across all flow rate experiments by interpolating the test results in Fig. 1c. The slope was found to depend on the flow regime of the foam. This dichotomy has been observed by others, and it is linked to the texture and type of foam flow31,40. A slope of − 0.28 was identified in the high-quality regime for \({f}_{g}\) = 0.97 (Fig. 3a). A slope of 0.00 would correspond to a Newtonian fluid. Because the foam in the high-quality regime is flowing as a coarse foam, the number of lamellae per unit length is relatively small, and the influence of these lamellae on apparent viscosity diminishes with decreasing number. As the foam transitions to a completely continuous-gas foam with further increases in \({f}_{g}\), the rheology behavior should become Newtonian. In the low-quality regime, where foam is fine, lamellae heavily influence the rheology. A slope of − 0.9 was identified for \({f}_{g}\) = 0.4 (Fig. 3b). This slope is larger in magnitude than the slope of − 0.67 reported by Falls et al. for bead-pack-generated foam in a glass bead pack, by Hirasaki and Lawson6,7 for “bulk” foam in smooth glass capillaries, and by Pedroni and Nabzar for in-situ generated foam in Fontainebleau sandstone cores40. A slope of − 1.0 would correspond to a perfectly shear-thinning fluid and has been observed by Persoff et al. in a Boise Sandstone41. Because the overall pressure drop was measured and a foam pre-generator was incorporated in the setup reported here, it is possible that end effects are affecting the measured pressure drops. Sand of the same type as that in the main pack was selected for the foam pre-generator to mitigate end effects potentially caused by injected gas slugs being either too small or too large. Indeed, transitions in pressure-drop trends coincided with capillary pressure trends, so end effects should be insignificant. Some researchers have concluded that foam texture will quickly adjust to the final form within a short distance from the entrance of the porous medium42. In-situ observations of foam texture appeared to show that this was also the case for the systems tested here by comparing visuals of the foam near inlet, middle, and outlet of the sandpack.
In Fig. 3c, upon transitioning between the low- and high-quality regimes, with increasing velocity, a distinct shift in slope is observed. This observation may be important in correctly interpreting apparent-viscosity results in that transition between the low- and high-quality foam regimes and could cause misinterpretation of the foam rheology if unrecognized.
Comparison of nitrogen and carbon dioxide foam
As seen in Fig. 4a, the measured capillary pressures for CO2 foam are lower than those of the N2 cases at similar flow rates across all conditions. This finding might be expected because CO2 foam is generally recognized as being “weaker” than N2 foams22,23,24,43,44, and a higher gas mobility, associated with “weaker” foams, would lead to a high liquid-phase saturation and consequently a lower capillary pressure. The plateau in \({P}_{c}\) for the CO2 case appears to be more rounded, and it contains fewer data points than those of the N2 cases.
At the test conditions, the surface tensions of each system are nearly identical. Despite this, CO2 exhibits similar transition foam quality to N2 (Fig. 4b), but CO2 foam also resulted in lower pressure gradients. This might indicate that the foam generation is independent of gas type; however, due to the high solubility of CO2 in the aqueous phase, Ostwald ripening/diffusion coarsening is playing a more significant role in CO2 foam destruction. Zeng et al. found that lamella permeability to gas is predicted to be the primary driver of differences in foam strength (in terms of pressure gradient or apparent viscosity)22. Higher film permeability leads to faster foam destruction by diffusion coarsening, and film permeability is proportional to gas solubility. If Ostwald ripening is the dominant mechanism of foam destruction, then the conventional accepted limiting capillary pressure theory does not accurately describe the foam behavior. This is because lamella rupture, at the limiting capillary pressure, is the only mechanism of bubble destruction considered to prevent foam texture from becoming finer in the established theory. However, it has also been argued that diffusion coarsening plays a small role in foam destruction in porous media under certain conditions, so more experiments are needed to explore if Ostwald ripening is the factor driving the differences among gas types45.
The transition foam qualities are indicated by the vertical dashed lines on Fig. 4b and c. For the CO2 11.4 × flow rate experiment, the transition foam quality occurs around \({f}_{g}\) = 0.93, which is very close to the same value for the comparable N2 case (\({f}_{g}\) = 0.92) and similar to literature reference values of 0.94 from Osterloh and Jante or 0.97 from Khatib et al.5,11. Corresponding to the lower capillary pressures for CO2 foam in Fig. 4a, lower pressure gradients and apparent viscosities are also observed.
Conclusion
Foam quality scans were conducted at fixed gas velocity in a 143-Darcy sand pack with foam pre-generation. A known strong-foaming solution of 1 wt% AOS12-16 in 3 wt% NaCl brine was selected. The overall pressure drop and capillary pressure were measured, and the microscopic foam structure was filmed in-situ. Both N2 and CO2 gas foams were tested. The following insights were gained:
-
1.
A plateau capillary pressure occurs in the low-quality regime across all velocities and test conditions evaluated in these experiments. The plateau values measured for capillary pressure in the N2 system were 0.53, 0.82, 1.02, and 1.14 psi for standard superficial gas velocities of 2.3 ft/day (8.2 × 10–6 m/s), 7 ft/day (2.5 × 10–5 m/s), 21 ft/day (7.4 × 10–5 m/s), and 42 ft/day (14.8 × 10–5 m/s) respectively.
-
2.
The capillary pressure curves of different gas velocities for the N2 foam system decrease in the high-quality regime with increasing foam quality to a convergent value of 0.3 psi.
-
3.
Transitions in capillary pressure and pressure gradient behavior were linked to foam texture (fine vs. coarse) and flow type (discontinuous vs. continuous). Fine foam in the low-quality regime exhibits high pressure gradients and contains a region of plateau capillary pressure. Pressure gradient and capillary pressure for coarse foams or continuous gas flow in the high-quality regime are a strong function of the gas fractional flow and liquid velocity.
-
4.
Transition foam qualities correspond to a transition between a coarse and a fine foam and depend mainly on the liquid velocity.
-
5.
Apparent viscosity curves of different gas velocity collapse onto one another in the high-quality regime and are a linear function of the fractional flow.
-
6.
Foam rheology is significantly shear thinning in the low-quality regime with a power-law exponent of − 0.9 and is closer to Newtonian in the high-quality regime with an exponent of − 0.28. Transitioning between regimes with increases in gas velocity resulted in a shift in the rheological trend for the same foam quality.
-
7.
The CO2 foam expectedly exhibited lower pressure gradients and apparent viscosities than N2 foam while both gas types resulted in similar transition foam quality. Plateau capillary pressure for the CO2 foam was also lower than that of the N2 foam in accord with the lower pressure gradients. The differences between gas types might be due to differences in the permeability of lamellae in the foam to each gas.
Some implications of these conclusions are as follows:
-
1.
In at least some systems in which foam is flowing in porous media, conventional “limiting” capillary pressure theory fails to explain the capillary pressure curve.
-
2.
Because the plateau capillary pressure was measured to be a function of velocity in this work, future studies will likely need to examine this relationship in detail to mathematically describe the relationship between velocity and the capillary pressure curve for foam flow in porous media.
-
3.
Foam rheology is dependent on foam type (continuous vs. discontinuous gas) and texture (fine vs. coarse) and, by extension, the foam flow regime (high vs. low quality). Therefore, foam rheology is nuanced and cannot be described unless the foam texture is known.
-
4.
For foams with highly soluble gas phases, Ostwald ripening should be given more consideration as a foam destruction mechanism. This is not considered in conventional limiting capillary pressure theory.
References
Føyen, T., Brattekås, B., Fernø, M. A., Barrabino, A. & Holt, T. Increased CO2 storage capacity using CO2-foam. Int. J. Greenhouse Gas Control 96, 103016 (2020).
Enick, R. M., Olsen, D., Ammer, J. & Schuller, W. Mobility and conformance control for CO2 EOR via thickeners, foams, and gels: A literature review of 40 years of research and pilot tests. OnePetro https://doi.org/10.2118/154122-MS (2012).
Nguyen, Q. P., Alexandrov, A. V., Zitha, P. L. & Currie, P. K. Experimental and modeling studies on foam in porous media: A review. OnePetro https://doi.org/10.2118/58799-MS (2000).
Ma, K., Ren, G., Mateen, K., Morel, D. & Cordelier, P. Modeling techniques for foam flow in porous media. SPE J. 20, 453–470 (2015).
Khatib, Z. I. et al. Effects of capillary pressure on coalescence and phase mobilities in foams flowing through porous media. SPE Reserv. Eng. 3, 919–926 (1988).
Hirasaki, G. J. & Lawson, J. B. Mechanisms of foam flow in porous media: Apparent viscosity in smooth capillaries. Soc. Petrol. Eng. J. 25, 176–190 (1985).
Falls, A. H., Musters, J. J. & Ratulowski, J. The apparent viscosity of foams in homogeneous bead packs. SPE Reserv. Eng. 4, 155–164 (1989).
Falls, A. H. et al. Development of a mechanistic foam simulator: The population balance and generation by snap-off. SPE Reserv. Eng. 3, 884–892 (1988).
Rossen, W. R. Theories of foam mobilization pressure gradient. In SPE-17358-MS (Society of Petroleum Engineers, 1988). https://doi.org/10.2118/17358-MS.
Rossen, W. R. Minimum pressure gradient for foam flow in porous media: Effect of interactions with stationary lamellae. J. Colloid Interface Sci. 139, 457–468 (1990).
Osterloh, W. T. & Jante, M. J. Jr. Effects of Gas and Liquid Velocity on Steady-State Foam Flow at High Temperature (Society of Petroleum Engineers, 1992). https://doi.org/10.2118/24179-MS.
Kam, S. I. & Rossen, W. A model for foam generation in homogeneous media. SPE J. 8, 417–425 (2003).
Lopez-Salinas, J. L. Transport of Components and Phases in a Surfactant/Foam EOR Process for a Giant Carbonate Reservoir (Rice University, 2012).
Ren, G., Zhang, H. & Nguyen, Q. Effect of surfactant partitioning on mobility control during carbon-dioxide flooding. In SPE-145102-PA (2013). https://doi.org/10.2118/145102-PA.
Yu, G., Rossen, W. R. & Vincent-Bonnieu, S. Coreflood study of effect of surfactant concentration on foam generation in porous media. Ind. Eng. Chem. Res. 58, 420–427 (2019).
Kahrobaei, S., Vincent-Bonnieu, S. & Farajzadeh, R. Experimental study of hysteresis behavior of foam generation in porous media. Sci. Rep. 7, 8986 (2017).
Farajzadeh, R. Enhanced Transport Phenomena in CO2 Sequestration and CO2 EOR (Springer, 2009).
Aronson, A. S., Bergeron, V., Fagan, M. E. & Radke, C. J. The influence of disjoining pressure on foam stability and flow in porous media. Colloids Surf. A 83, 109–120 (1994).
Shah, S. Y., Wolf, K.-H., Pilus, R. M. & Rossen, W. R. Foam generation by capillary snap-off in flow across a sharp permeability transition. SPE J. 24, 116–128 (2018).
Farajzadeh, R., Lotfollahi, M., Eftekhari, A. A., Rossen, W. R. & Hirasaki, G. J. H. Effect of permeability on implicit-texture foam model parameters and the limiting capillary pressure. Energy Fuels 29, 3011–3018 (2015).
Gauglitz, P. A., Friedmann, F., Kam, S. I. & Rossen, W. R. Foam generation in homogeneous porous media. Chem. Eng. Sci. 57, 4037–4052 (2002).
Zeng, Y. Effect of Gas Type and Composition on Foam Rheology in Porous Media for EOR (Springer, 2015).
Solbakken, J. Experimental Studies of N2- and CO2-Foam Properties in Relation to Enhanced Oil Recovery Applications (The University of Bergen, 2015).
Farajzadeh, R. Effect of Gas Type and Composition on Macroscopic Properties of Foam (Springer, 2014).
Abdelgawad, K. Z., Adebayo, A. R., Isah, A. & Muhammed, N. S. A literature review of strength and stability of foam and their relationship with the absolute permeability of porous media. J. Petrol. Sci. Eng. 211, 110195 (2022).
Adebayo, A. R. Foam flow in different pore systems—part 2: The roles of pore attributes on the limiting capillary pressure, trapping coefficient, and relative permeability of foamed gas. SPE J. 26, 3926–3948 (2021).
Kibodeaux, K. R. & Rossen, W. R. Coreflood Study of Surfactant-Alternating-Gas Foam Processes: Implications for Field Design (Society of Petroleum Engineers, 1997). https://doi.org/10.2118/38318-MS.
Adebayo, A. R. Foam flow in different pore systems—part 1: The roles of pore attributes and their variation on trapping and apparent viscosity of foam. SPE J. 26, 3908–3925 (2021).
Vavra, E. et al. Measuring in-situ capillary pressure of a flowing foam system in porous media. J. Colloid Interface Sci. 621, 321–330 (2022).
Jimenez, A. I. & Radke, C. J. Dynamic Stability of a Foam Lamella Flowing Through a Periodically Constricted Tube (Springer, 1987).
Alvarez, J. M., Rivas, H. J. & Rossen, W. R. Unified Model for Steady-State Foam Behavior at High and Low Foam Qualities (Society of Petroleum Engineers, 1999). https://doi.org/10.2118/56825-MS.
Ouali, C., Rosenberg, E., Barré, L. & Bourbiaux, B. A CT-scanner study of foam dynamics in porous media. Oil Gas Sci. Technol. Rev. 74, 33 (2019).
Ettinger, R. A. & Radke, C. J. Influence of texture on steady foam flow in berea sandstone. SPE Reserv. Eng. 7, 83–90 (1992).
Getrouw, N. A. S. The Dynamic and Static Behaviour of Foam in a Model Porous Media (Springer, 2016).
Kam, S. I. Improved mechanistic foam simulation with foam catastrophe theory. Colloids Surf. A 318, 62–77 (2008).
Ma, K. et al. Estimation of parameters for the simulation of foam flow through porous media. Part 1: The dry-out effect. Energy Fuels 27, 2363–2375 (2013).
Zeng, Y. et al. Insights on foam transport from a texture-implicit local-equilibrium model with an improved parameter estimation algorithm. Ind. Eng. Chem. Res. 55, 7819–7829 (2016).
Moradi-Araghi, A., Johnston, E. L., Zornes, D. R. & Harpole, K. J. Laboratory evaluation of surfactants for CO2-foam applications at the south Cowden unit. OnePetro https://doi.org/10.2118/37218-MS (1997).
Grigg, R. et al. Improving Gas Flooding Efficiency. https://www.osti.gov/biblio/953470 (2008). https://doi.org/10.2172/953470.
Pedroni, L. & Nabzar, L. New Insights on Foam Rheology In Porous Media (Springer, 2016).
Persoff, P., Radke, C. J., Pruess, K., Benson, S. M. & Witherspoon, P. A. A laboratory investigation of foam flow in sandstone at elevated pressure. SPE Reserv. Eng. 6, 365–372 (1991).
de Vries, A. S. & Wit, K. Rheology of gas/water foam in the quality range relevant to steam foam. SPE Reserv. Eng. 5, 185–192 (1990).
Aarra, M. G. et al. Experimental study of CO2-and methane-foam using carbonate core material at reservoir conditions. In SPE Middle East Oil and Gas Show and Conference (Society of Petroleum Engineers, 2011).
Farajzadeh, R., Andrianov, A., Bruining, H. & Zitha, P. L. J. Comparative study of CO2 and N2 foams in porous media at low and high pressure−temperatures. Ind. Eng. Chem. Res. 48, 4542–4552 (2009).
Nonnekes, L. E., Cos, S. & Rossen, W. R. Effect of Gas Diffusion on Mobility of Foam for EOR (Society of Petroleum Engineers, 2012). https://doi.org/10.2118/159817-MS.
Acknowledgements
The authors thanks TotalEnergies E&P R&T USA, LLC and the Rice Consortium for Processes in Porous Media for research funding.
Author information
Authors and Affiliations
Contributions
E.V., C.B., and M.P. carried out experiments and wrote the main manuscript. K.M. and K.M. provided conceptualization and funding acquisition. G.J.H. and S.L.B. provided conceptualization, project administration, and reviewed and edited draft.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Supplementary Video 1.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Vavra, E., Bai, C., Puerto, M. et al. Effects of velocity on N2 and CO2 foam flow with in-situ capillary pressure measurements in a high-permeability homogeneous sandpack. Sci Rep 13, 10029 (2023). https://doi.org/10.1038/s41598-023-36345-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-36345-4
- Springer Nature Limited