Abstract
In this study, the effects of wind on an Eastern Red Cedar were investigated using numerical simulations. Two different tree models were proposed, each with varying bole lengths and canopy diameters. A total of 18 cases were examined, including different canopy diameters, bole lengths, and wind velocities. Using computational fluid dynamics (CFD) methods, the drag force, deformation, and stress of the tree models were calculated under different wind velocities and geometric parameters. A one-way fluid–structure interaction (FSI) method was used to solve the deformation of the tree. Additionally, velocity and pressure distribution around the tree were obtained. The results indicate that wind velocity and geometric parameters of the tree have a significant impact on deformation, drag force, and stress. As wind velocity increases from 15 to 25 m/s, the force on the tree increases substantially. The results also show that the diameter of the canopy has a bigger effect on stress and strain than the bole length. This study provides insights into tree behavior under wind loading for urban planning and design, informing optimal tree selection and placement for windbreak effectiveness and comfortable environments.
Similar content being viewed by others
Introduction
Ocean levels are rising due to climate change, which is creating an unprecedented amount of catastrophic weather occurrences1,2. The number of people on earth is still rising3, and urban areas are developing and growing4. Most of these listed objectives may be met with environmental and natural methods5. Prior studies have linked environmental issues with solutions to achieve the UN SDGs, including plant protection6, soil and soil science7, and the avoidance of land degradation8. The literature has shown a connection between trees, green areas, and mortality9,10,11,12. In one study, the authors linked the infestation and demise of ash trees in counties throughout the United States to an increase in cardiovascular and respiratory fatalities13. The correct mature kinds of trees planted in the right places can help reduce the particle problem and other types of air pollution, which can help to lower mortality and morbidity in our urban areas. Moreover, trees have impacts on urban planning, design, landscape architecture, and urban climate. Urban trees have the ability to change the temperature, humidity, wind speed, and contaminants in the air14. According to some studies15,16,17,18,19,20, certain specific characteristics, such as the structure and density of the tree, size, shape, and color affect the environment. According to the ways that tree canopies reflect, transmit, and absorb solar radiation and regulate wind speed, they may adapt to microclimates21. In tropical climates, the potential for shifting wind patterns and shadows will alter the microclimate and enhance thermal comfort for people22,23,24. Rows of trees or bushes that act as windbreaks can lessen the wind’s power. They have the ability to lower soil erosion, boost agricultural yields, and shield cattle from the heat and cold. Buildings and roads can be protected from drifting snow by windbreaks. They enhance the environment and give wildlife access to the landscape as well as habitat. Windbreaks can be used as food and wood sources. They can transfer of sand particles, microclimate and soil conditions25. Windbreaks can be made of natural materials, such as trees and vegetation, or industrial materials, like a concrete wall. Vegetation barriers are used to reduce noise pollution and high wind velocity in cities. Despite the low expense of these shelters26, they may not provide enough protection. If the protected building is a low-rise one, one row of trees may be enough to provide enough protection. For higher cases or larger areas, several rows may provide enough protection27. Natural vegetation and especially trees mitigate soil erosion. Soil erosion induces loss of soil nutrients and water, water pollution, and global change28. Soil degradation is one of the most noteworthy natural issues in the world. In semiarid Mediterranean regions, the dry climate leads to a low level of plant cover, which, in turn, leads to low soil structure development29. In China, there are about 3.3 million km2 of desertified lands caused by wind erosion30,31. In combination with field tests, numerical models may give more noteworthy knowledge about the wind-induced drag acting on trees beneath distinctive scenarios. Later improvements in computational fluid dynamics (CFD), experimental and field studies have looked for the complex and energetic wind–tree interaction, in order to gauge the force that the tree can persevere in given areas and evaluate the tree’s situation and the hazard of tree failure. Since the 1950s, researchers have examined the optimization of vegetative windbreaks and found that efficiency is determined by numerous contributing components. Windbreak height is the major controlling factor, and the length of a windbreak ought to be at least ten times its height32. Moreover, windbreaks perpendicular to the approaching speed were found to be more compelling33. A windbreak’s width can also impact its viability (number of rows) and is additionally critical for shielding34. Last but not least, the geometry and density of trees are key factors35. Because of their wide range of agricultural applications, dense canopies have been the focus of many recent transport process studies36,37,38,39. Trees with heights much greater than the spacing of individual plants characterize dense canopies. Pietri et al.40 conducted experiments on dense and sparse canopies to investigate the effect of canopy density on turbulence characteristics within and above canopies. In addition to dense tree canopies, recent research has focused on windbreaks and forest clearings41,42. The horizontal spacing between plants in this type of canopy is greater than the plant height. These types of canopies are useful for erosion control and shelter. Many studies have been carried out to better understand windbreaks and their effects on atmospheric surface-layer flow fields. Speckart and Pardyjak43 developed and implemented models for mean and fluctuating velocities around a windbreak in a simple, empirically based CFD code. Mayaud et al.44 investigated the effects of a single tree, a grass clump, and a shrub on turbulent wind flow and discovered that wind velocity can be reduced by up to 70% in the lee of vegetation. Leenders et al.45 investigated wind velocity patterns and wind-induced soil erosion in the vicinity of five different types of vegetation. Their findings revealed that wind velocity was reduced close to the soil surface for shrubs but increased around the trunk for trees. Numerical studies of sparse canopies have used different methods, including Reynolds Averaged Navier–Stokes (RANS) and Large-Eddy Simulation (LES) solvers. Numerous studies have also been done on numerical wind flow predictions. These were regarded as inefficient in the execution of numerical flow computations because complete descriptions of the geometries of twigs and leaves in tree crowns need a significant amount of computer time. To investigate how the urban canopy layer contributes to the development of a nighttime urban boundary layer, Uno et al.46 devised a second-order turbulence model. Hiraoka47 used ensemble-averaging and spatial averaging approaches based on the eddy-viscosity concept to simulate flows in plants and urban canopies. In order to properly depict the crown penetration characteristics, Shaw and Schumann48 suggested adding the proper source terms to the momentum equations used in flow simulations of the spatial sections of tree crowns. The combined effects of the drag coefficient, leaf density, and combined velocities resulted in the newly introduced drag terms. A 2-D numerical model was also used by Wilson and Flesch49 to simulate flow fields in forests. Comparatively, the in-field results and forecasted wind velocity profiles were in good agreement. Wei et al.50 studied the effect of meteorological parameters in winter and summer and human thermal comfort in different landscapes of an urban park in China. They examined several factors and concluded that in summer, the most comfortable type of landscape space is wood. Wang et al.51 showed the correlation between green space and improvements in adult health. In a similar study, Liu et al.52 investigated the impact of environmental parameters such as trees on the mental and physical health of residents. Drag force, deformation, and stress of a three-dimensional T-shaped flexible beam were investigated numerically and experimentally by Malazi et al.53. They used a two-way fluid–structure interaction (FSI) numerical method for all simulations. A system coupling was employed to connect the fluid and solid domains. Furthermore, an open channel with a high-quality camera was used for the measurement of deformation on a T-shaped flexible beam. Between the numerical and experimental methods, good results were obtained.
In this study, a systematic investigation of windbreaks using CFD simulations has been conducted, and the Eastern Red Cedar was selected as a model tree to evaluate various parameters. The study begins by introducing the numerical simulation methods, followed by a discussion of the analysis results and the selection of optimal design parameters. Finally, conclusions are presented, including a discussion of the novelty and limitations of the study. Additionally, the study provides valuable insights into the behavior of trees under wind loading and the key parameters that influence the performance of trees as windbreaks. This can inform the selection and placement of trees in urban areas to optimize their effectiveness in reducing wind velocities and creating more comfortable environments for residents. Furthermore, the examination of tree deformation and stress on soil can assist in selecting appropriate ground for trees with different bole lengths and crown diameters, which is crucial for selecting soil in parks.
Materials and methods
Governing equations and numerical methods
Ansys Workbench-system coupling was applied for the solution of one-way fluid–structure interaction. First, the fluid domain calculates in the Ansys Fluent part, and the solid domain computes in the Ansys Mechanical part. Then a coupling system connects the two parts together. The forces obtained on the fluid side are transferred to the solid side, and then the displacement, stress, and strain of the solid part can be calculated. In this study, the realizable k–ε turbulence model was used for solving the fluid domain, and the static structure method was employed for solving the solid domain. Details of the models were explained below.
Computational fluid dynamics (CFD)
The turbulent flow simulation in the three-dimensional computational fluid domain was implemented using the realizable k-ɛ turbulence model53,54. The continuity and momentum formulas can be shown as:
where \(\rho \) is the density. \({u}_{i}\, and\, {u}_{j}\) represent the average velocity component of the fluid. P is pressure, Si is the source term for the momentum equation, \(\mu \) represents the dynamic viscosity, \({\mu }_{t}\) represents the eddy viscosity, and it is calculated as \({\mu }_{t}=\rho {C}_{\mu }\frac{{k}^{2}}{\varepsilon }\). The transport equations for \(k\, and \,\varepsilon \) for the realizable k–ɛ model can be written as,
where k represents the turbulent kinetic energy. ɛ represents the rate of dissipation. \({G}_{k}\) is turbulent kinetic energy generation, \({G}_{b}\) is turbulent kinetic energy generation, and \({Y}_{M}\) is fluctuating dilatation contribution to the overall dissipation rate. The model constants for the realizable k-ɛ turbulence model can be written \({C}_{1\varepsilon }=1.44\), \({C}_{2\varepsilon }=1.92\), \({\sigma }_{k}=1.0\), \({C}_{\mu }=0.09\), and \({\sigma }_{\varepsilon }=1.3.\)
Computational structural dynamics (CSD)
A three-dimensional flexible solid structure's deformation is explained by the equation of motion53, which can be given as follows:
where [M] represents the structural mass matrix, [C] represents the structural damping matrix, [K] represents the structural stiffness matrix, and \(\left\{F\right\}\) represents the applied load vector acting on the solid structure caused by fluid. \(\left\{\ddot{u}\right\}\) represents the nodal acceleration vector, \(\left\{\dot{u}\right\}\) represents the nodal velocity vector, and \(\left\{u\right\}\) represents the nodal displacement vector.
Computational model and physical conditions
Eastern Red Cedar has been selected as the tree model. This wood type has very low shrinkage. This species is lightweight, moderately soft, and low in strength when used as a beam or post, and low in shock resistance. The heartwood is very resistant to decay55.
The present study investigates two three-dimensional models of an Eastern Red Cedar tree at various geometry parameters numerically (Fig. 1). The canopy diameter of model 1 and model 2 is 2.432 m and 1.216 m. Both models 1 and 2 are pursued at three various bole lengths (0.5 m, 1.0 m, and 1.5 m) and three various wind velocities (15 m/s, 20 m/s, and 25 m/s) with a constant trunk diameter (0.1 m) and a constant crown length (3 m). In this study, 18 different models are analyzed. The details of the numerical simulations carried out in this study are represented in Table 1. The characteristics of air, trees, and soil have been selected as shown in Table 2.
Figure 2 demonstrates the typical model of the computational domain and boundary conditions. A single tree has been modeled in this analysis. Lc denotes the crown length of the tree (3 m). The height, length, and width of the domain are defined as 6 Lc, 30 Lc, and 10 Lc. The velocity inlet boundary condition is located at 10 Lc upstream of the tree, and the pressure outlet boundary condition is located at 20 Lc downstream of the tree. The free slip boundary condition is selected for the upper part of the model.
Tetrahedron and prism with triangle base mesh were used in the computational fluid domain with high-quality mesh near walls, and tetrahedron mesh is applied in the computational solid domain. As presented in Fig. 3, nearly 13 million elements are used to solve the computational fluid domain, and 6 million elements are applied to solve the solid computational domain.
Simulation methodology and ethical considerations
This study was based solely on computer simulation and did not involve the use of real Red Cedar plants or any experimentation with plants. This simulation had no conflict with relevant institutional, national, and international guidelines and legislation regarding the ethical use of living organisms in research.
Results and discussion
Drag force study
Drag force can act on a body when it is placed in the fluid flow53. Drag force on a tree during wind blowing can be calculated using Eq. (6).
where, \({F}_{D\_pressure}\) is pressure drag, \({F}_{D\_viscous}\) is viscous drag, \(p\) is the pressure, and \(\tau \) is the wall share stress.
Once the drag force has been computed, the drag coefficient can be calculated using Eq. (7).
where CD is the drag coefficient, \({F}_{Drag}\) is the total drag force, ρ is the density of the fluid, U is the velocity of the fluid, and A is the characteristic area of the body (tree frontal area).
Table 3 represents the comparison of the drag coefficient results between this study and others when the wind velocity is 20 m/s. It was realized that Eastern Red Cedar models 1 and 2 presented very close drag coefficients to real trees.
Figure 4 shows the variation of the total force with respect to the wind velocity in tree models at different bole lengths (0.5 m, 1.0 m, and 1.5 m). Total forces increase with increased wind velocity for models 1 and 2. Total forces are increased by nearly 180% at model 1 when wind velocity changes from 15 to 25 m/s. Moreover, total forces are increased by nearly 200% at model 2 when wind velocity changes from 15 to 25 m/s. The total force has its maximum value when the bole length is 1.5 m for both models. The total force of model 1 is nearly 70% greater than that of model 2 when the wind velocity is 25 m/s. It can be concluded that the canopy diameter has a great influence on the total force. As the diameter increases twice, the total force increases by the same ratio. Moreover, the negligible effect of bole length can be concluded too. A comparison of two models reveals that the canopy diameter has a much more significant effect on the total force results as the canopy diameter decreases.
Deformation, stress and strain study
Total deformation can be computed in a three-dimensional flexible solid structure numerically. Total deformation is obtained using Eq. (8).
where \({\mathrm{U}}_{\mathrm{x}}\), \({\mathrm{U}}_{\mathrm{y}}\), and \({\mathrm{U}}_{\mathrm{z}}\) are component deformations in the x, y, and z directions, respectively.
In Fig. 5, the total deformations of the models 1 and 2 with different bole lengths are compared. It can be shown that bole length and canopy diameter have a significant effect on the total deformation. In the same trend, with an increase in wind velocity, this deformation difference with variable length increases considerably. The reduction trend is the same for both models, though the total deformation for model 2 for all bole lengths reduces in comparison with model 1. The deformation of tree models 1 and 2 increased with increasing wind velocity and bole canopy. Maximum deformation occurs when wind velocity and bole length are at their maximum values for models 1 and 2.
Van Mises stress can be computed in a three-dimensional flexible solid structure numerically. Van Mises stress is obtained using Eq. (9).
where \({\upsigma }_{1}\), \({\upsigma }_{2}\) and \({\upsigma }_{3}\) are stress states in the x, y, and z directions, respectively.
Figure 6 depicts the values of Von Mises maximum stress for different wind velocities and bole lengths. It is obvious that the wind velocity has a significant effect on maximum stress in models 1 and 2. As the velocity increases to 25 m/s, the maximum stress increases as much as three times. Moreover, it can be concluded that the bole length effect is more obvious in model 1 than model 2.
Equivalent strain can be computed numerically in a three-dimensional flexible solid structure. Equivalent strain is obtained using Eq. (10).
where \({\upvarepsilon }_{1}\), \({\upvarepsilon }_{2}\) and \({\upvarepsilon }_{3}\) are principal strains in the in the x, y, and z directions, respectively.\({\upsilon }^{\mathrm{^{\prime}}}\) represents effective Poisson’s ratio.
Figure 7 depicts the equivalent strain with respect to wind velocity for different bole lengths. The strain is directly proportional to the bole length and wind velocity for both models. As the bole length increases, the strain increases as well. The increase is also dependent on the diameter.
Contours plots of numerical study
The deformation of tree models is illustrated for various bole lengths (0.5 m, 1 m, and 1.5 m) and various wind velocities (15 m/s, 20 m/s, and 25 m/s) (Fig. 8). The velocity contours of the computational domain are plotted in the (Fig. 9) for different bole lengths (0.5 m, 1 m, and 1.5 m) and different wind velocities (15 m/s, 20 m/s, and 25 m/s). The minimum velocity occurs on the front surface of all tree models because high pressure is created in the front of the tree. Pressure contours of the computational domain are drawn in Fig. 10 for various bole lengths (0.5 m, 1 m, and 1.5 m) and various wind velocities (15 m/s, 20 m/s, and 25 m/s). It was noted that the large pressure happens on the front surface of the trees. It was noted that the large pressure regions happen on the front surface of the tree for all models. The lower pressure regions occur at the top of the tree and between the bottom of the tree and the ground. It was also realized that the pressure on model 1 is greater than on model 2 because of the larger surface.
Conclusions
In this study, two different three-dimensional tree models were examined numerically using various body dimensions. Models 1 and 2 were evaluated under different wind velocities (15 m/s, 20 m/s, and 25 m/s) while varying the bole length from 0.5 to 1.5 m. The realizable k-e turbulence model was used to solve the fluid domain, and a one-way FSI method was employed to calculate both the fluid and solid domains together. The results of the total force, deformation, maximum stress, maximum strain, velocity distribution, and pressure distribution of both tree models were obtained at various geometry parameters and wind velocities. The results indicate that total force, deformation, stress, and strain increased with increasing wind velocity for both models. Additionally, deformation and stress were directly influenced by bole length, canopy diameter, and wind velocity when trunk diameter was constant. It was also observed that a high total force can cause significant deformation and stress in a tree. Model 1 demonstrated a greater total force than model 2 due to its larger diameter. The greatest deformation occurred at a wind velocity of 25 m/s and a bole length of 1.5 m for both models 1 and 2. Overall, it can be concluded that the chosen model tree can effectively hinder wind force, but it is important to note that parameters associated with the physical properties of the tree, such as length and diameter, can affect this function. The results of this study can be applied to urban planning and design by providing valuable information on how trees react to wind loading and which factors determine their effectiveness as windbreaks. This knowledge can help to improve the selection and placement of trees in urban areas, making the environment more comfortable for residents by reducing wind velocities.
Data availability
The datasets used and/or analyzed during the current study available from the corresponding author on reasonable request.
References
Goudie, A. S. Human Impact on the Natural Environment: Past, Present and Future (Wiley, 2019).
Amani-Beni, M., Chen, Y., Vasileva, M., Zhang, B. & Xie, G. D. Quantitative-spatial relationships between air and surface temperature, a proxy for microclimate studies in fine-scale intra-urban areas? Sustain. Cities Soc. 77, 103584 (2022).
United Nations. World Population Prospects: The 2015 Revision (United Nations, Department of Economic and Social Affairs, Population Division, 2015).
Mokhtari, Z., Barghjelveh, S., Sayahnia, R., Qureshi, S. & Russo, A. Dynamic and heterogeneity of urban heat island: A theoretical framework in the context of urban ecology. Land 11(8), 1155 (2022).
Soltanifard, H., Roshandel, T. & Ghodrati, S. Assessment and ranking of influencing factors in the relationship between spatial patterns of urban green spaces and socioeconomic indices in Mashhad urban districts, Iran. Model. Earth Syst. Environ. 6, 1589–1605 (2020).
Sharrock, S. & Jackson, P. W. Plant conservation and the Sustainable development goals: A policy paper prepared for the global partnership for plant conservation. Ann. Mo. Bot. Gard. 102(2), 290–302 (2017).
Keesstra, S. D. et al. The significance of soils and soil science towards realization of the United Nations Sustainable Development Goals. Soil 2(2), 111–128 (2016).
Vlek, P. L. G., Khamzina, A. & Lulseged, T. Land Degradation and the Sustainable Development Goals: Threats and Potential Remedies (International Center for Tropical Agriculture, 2017).
James, P., Hart, J. E., Banay, R. F. & Laden, F. Exposure to greenness and mortality in a nationwide prospective cohort study of women. Environ. Health Persp. 124(9), 1344–1352 (2016).
Nowak, D. J. & Greenfield, E. J. US urban forest statistics, values, and projections. J. Forest. 116(2), 164–177 (2018).
Villeneuve, P. J. et al. A cohort study relating urban green space with mortality in Ontario, Canada. Environ. Res. 115, 51–58 (2012).
Zhang, B., Amani-Beni, M., Shi, Y. & Xie, G.G.-D. The summer microclimate of green spaces in Beijing’ Olympic park and their effects on human comfort index (In Chinese). Ecol. Sci. 37(5), 77–86 (2018).
Donovan, G. H. et al. The relationship between trees and human health: Evidence from the spread of the emerald ash borer. Am. J. Prev. Med. 44, 2 (2013).
Streiling, S. & Matzarakis, A. Influence of single and small clusters of trees on the bioclimate of a city: A case study. J. Arboric. 29, 309–316 (2003).
Abreu-Harbich, L. V., Labaki, L. C. & Matzarakis, A. Different trees and configuration as microclimate control strategy in Tropics. In Proc. International Conference on Passive and Low Energy Architecture (PLEA, 2012).
Bueno-Bartholomei, C. L. & Labaki, L. C. How much does the change of species of trees affect their solar radiation attenuation? In Paper Presented at the Fifth International Conference on Urban Climate (2003).
Correa, E., Ruiz, M. A., Canton, A. & Lesino, G. Thermal comfort in forested urban canyons of low building density. An assessment for the city of Mendoza, Argentina. Build. Environ. 58, 219–230 (2012).
Gulyás, A., Unger, J. & Matzarakis, A. Assessment of the microclimatic and thermal comfort conditions in a complex urban environment: Modeling and measurements. Build. Environ. 41, 1713–1722 (2006).
Scudo, G. Thermal comfort in green spaces. In Green Structures and Urban Planning. http://www.greenstructureplanning.eu/COSTC11/comfort.html (2002).
Shashua-Bar, L., Pearlmutter, D. & Erell, E. The cooling efficiency of urban landscape strategies in a hot dry climate. Landsc. Urban Plan. 92(3–4), 179–186 (2009).
Steven, M., Biscoe, P., Jaggard, K. & Paruntu, J. Foliage cover and radiation interception. Field Crop Res. 13, 75–87 (1986).
Lin, T. P., Matzarakis, A. & Hwang, R. L. Shading effect on long-term outdoor thermal comfort. Build. Environ. 45, 213–221 (2010).
Amani-Beni, M., Khalilnezhad, M. R. & Mahdizadeh, S. Hierarchical access to the edible landscape: The Akbarieh Garden in Iran. Landsc. Res. 47, 333–353 (2021).
Amani-Beni, M., Xie, G., Yang, Q., Russo, A. & Khalilnezhad, M. R. Socio-cultural appropriateness of the use of historic Persian gardens for modern urban edible gardens. Land 11, 38 (2022).
Liu, B., Qu, J., Zhang, W., Tan, L. & Gao, Y. Numerical evaluation of the scale problem on the wind flow of a windbreak. Sci. Rep. 4, 20–22. https://doi.org/10.1038/srep06619 (2014).
Mahgoub, A. O. & Ghani, S. Numerical and experimental investigation of utilizing the porous media model for windbreaks CFD simulation. Sustain. Cities Soc. 65, 102648 (2021).
Brandle, J. R., Hodges, L. & Wight, B. Windbreak Practices 79–118 (North American Agroforestry, 2009).
Zuazo, V. & Pleguezuelo, C. Soil-erosion and runoff prevention by plant covers. A review. Agron. Sustain. Dev. 28(1), 65–86 (2008).
Díaz, E., Roldán, A., Lax, A. & Albaladejo, J. Formation of stable aggregates in degraded soils by amendment with urban refuse and peat. Geoderma 63, 277–288 (1994).
Zhong, D. Dynamical Evolution of Sand Sea in China (Gansu Culture Press, 1998).
Zhong, D. & Qu, J. Recent developmental trend and prediction of sand deserts in China. J. Arid. Environ. 53(3), 317–329 (2003).
Brandle, J. R., Hodges, L. & Zhou, X. H. Windbreaks in North American agricultural systems. Agrofor. Syst. 61–62(1–3), 65–78 (2004).
Wang, H., Takle, E. S. & Shen, J. Shelterbelts and windbreaks: Mathematical modeling and computer simulations of turbulent flows. Adv. Mech. 33(1), 549–586 (2003).
Heisler, G. M. & Dewalle, D. R. Effects of windbreak structure on wind flow. Agric. Ecosyst. Environ. 22(88), 41–69 (1988).
Zhu, J., Jiang, F., Fan, Z. & Zhou, X. Optimization of spatial arrangements and patterns for shelterbelts or windbreaks. Chin. J. Appl. Ecol. 14(8), 1205 (2003).
Finnigan, J. Turbulence in plant canopies. Annu. Rev. Fluid Mech. 32, 519–571 (2000).
Cescatti, A. & Marcolla, B. Drag coefficient and turbulence intensity in conifer canopies. Agric. For. Meteorol. 121, 197–206 (2004).
Cava, D. et al. Buoyancy and the sensible heat flux budget within dense canopies. Bound. Layer Meteorol. 118, 217–240 (2006).
Poggi, D. & Katul, G. An experimental investigation of the mean momentum budget inside dense canopies on narrow gentle hilly terrain. Agric. For. Meteorol. 144, 1–13 (2007).
Pietri, L., Petroff, A., Amielh, M. & Anselmet, F. Turbulence characteristics within sparse and dense canopies. Environ. Fluid Mech. 9(3), 297 (2009).
Miller, N. E., Stoll, R., Mahaffee, W. F., Neill, T. M. & Pardyjak, E. R. An experimental study of momentum and heavy particle transport in a trellised agricultural canopy. Agric. For. Meteorol. 211–212, 100–114 (2015).
Poette, C. et al. The impact of landscape fragmentation on atmospheric flow: A wind-tunnel study. Bound. Layer Meteorol. 163(3), 393–421 (2017).
Speckart, S. & Pardyjak, E. A method for rapidly computing windbreak flow field variables. J. Wind Eng. Ind. Aerodyn. 132, 101–108 (2014).
Mayaud, J. R., Wiggs, G. F. & Bailey, R. M. Characterizing turbulent wind flow around dryland vegetation. Earth Surf. Proc. Land. 41(10), 1421–1436 (2016).
Leenders, J., Van Boxel, J. & Sterk, G. The effect of single vegetation elements on wind speed and sediment transport in the sahelian zone of Burkina Faso. Earth Surf. Process Landforms 32, 1454–1474 (2007).
Uno, I., Ueda, H. & Wakamatsu, S. Numerical modeling of the nocturnal urban boundary layer. Bound. Layer Meteorol. 49, 77–98 (1989).
Hiraoka, H. Modelling of turbulent flows within plant/urban canopies. J. Wind Eng. Ind. Aerod. 46–47, 173–182 (1993).
Shaw, R. H. & Schumann, U. Large-eddy simulation of turbulent flow above and within a forest. Bound. Layer Meteorol. 61, 47–64 (1992).
Wilson, J. D. & Flesch, T. K. Wind and remnant tree sway in forest cutblocks. III. A window model to diagnose spatial variation. Agric. For. Meteorol. 93, 259–282 (1999).
Wei, D., Yang, L., Bao, Z., Lu, Y. & Yang, H. Variations in outdoor thermal comfort in an urban park in the hot-summer and cold-winter region of China. Sustain. Cities Soc. 77, 103535 (2022).
Wang, R. et al. Exploring the impacts of street-level greenspace on stroke and cardiovascular diseases in Chinese adults. Ecotoxicol. Environ. Saf. 243, 113974 (2022).
Liu, J., Yang, L., Xiao, L. & Tao, Z. Perceived neighborhood environment impacts on health behavior, multi-dimensional health, and life satisfaction. Front. Public Health 10, 850923 (2022).
Tabatabaei Malazi, M., Eren, E. T., Luo, J., Mi, S. & Temir, G. Three-dimensional fluid–structure interaction case study on elastic beam. J. Mar. Sci. Eng. 8, 714 (2020).
Olcay, A. B. & Tabatabaei Malazi, M. The effects of a longfin inshore squid’s fins on propulsive efficiency during underwater swimming. Ocean Eng. 128, 173–182 (2016).
USDA. Wood Handbook, Wood as an Engineering Material, General Technical Report FPL-GTR-190 508 (U.S. Department of Agriculture, Forest Service, Forest Products Laboratory, 2010).
Young, D. F., Munson, B. R., Okiishi, T. H. & Huebsch, W. W. A Brief Introduction to Fluid Mechanics 5th edn. (Wiley, 2010).
Cengel, Y. A. & Cimbala, J. M. Fluid Mechanics: Fundamentals and Applications 2nd edn. (McGraw-Hill, 2009).
Acknowledgements
This research was supported by the National Natural Science Foundation of China (Grant No. 52150410414).
Author information
Authors and Affiliations
Contributions
M.A.B. and M.T.M. and K.D. and L.D. wrote the main manuscript text, and K.D. prepared the figures. M.A.B. and M.T.M. and K.D. and L.D. revised the manuscript. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Amani-Beni, M., Tabatabaei Malazi, M., Dehghanian, K. et al. Investigating the effects of wind loading on three dimensional tree models using numerical simulation with implications for urban design. Sci Rep 13, 7277 (2023). https://doi.org/10.1038/s41598-023-34071-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-023-34071-5
- Springer Nature Limited