Abstract
The gradient-index (GRIN) Luneburg lens antenna offers significant benefits, e.g. high aperture efficiency, low-power, minimal cost, wide beam scanning angle and broad bandwidth, over phased array antennas and reflector antennas. However, the spherical shape of the Luneburg lens geometry complicates the integration of standard planar feed sources and poses significant implementation challenge. To eliminate the feed mismatch problem, the quasi-conformal transformation optics (QCTO) method can be adopted to modify the lens’ spherical feed surface into a planar one. However, Luneburg lenses designed with QCTO method are limited to poor performance due to the presence of the reflections and beam broadening arising from the quasi-conformal mapping. In this paper, we present a new method of implementing QCTO-enabled modified Luneburg lens antenna by designing a broadband anti-reflective layer along with the modified lens’s planar excitation surface. The proposed anti-reflector layer is inherently broadband in nature, has a continuously tapered inhomogeneous dielectric permittivity profile along its thickness, and ensures broadband impedance matching. To show the new QCTO modified Luneburg lens antenna, an example lens antenna was designed at Ka-band (26–40 GHz) and fabricated using fused deposition modeling (FDM) based additive manufacturing technique. Electromagnetic performance of the lens antenna was experimentally demonstrated.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction
Modern wireless communication systems are increasingly focusing on high gain, agile, wide-angle, multiband and multibeam beamscanning antenna elements for applications in radar, electronic warfare, wireless and satellite communication systems1,2,3,4. Conventionally, these properties have been exclusively achieved by using either electronically steerable phased array antenna technology or mechanically steerable reflector antenna systems. Electronically steered phased array antenna system is very sophisticated and agile,however, this technology requires all the antenna elements to be active simultaneously and utilizes phase shifters at every antenna element for electronic beam steering. These antenna elements and phase shifters consume significant amount of DC electrical power making the phased array technology very expensive. On the other hand, the mechanically scanning reflector antennas are widely used for their simplicity, however, these antennas use mechanical rotating device to move the reflector toward the intended signal direction and the spinning speed of the rotary joint used in the reflector antenna constraints the antenna’s agile beamscanning capability. Additionally, the presence of the antenna feed at the front of the reflector creates signal blockage and requires a subreflector to avoid the feed blockage which makes the overall system cost-inefficient and bulky. An alternative to both the mechanically scanning reflector antennas and electronically scanning phased array antenna system is the use of the gradient-index (GRIN) lens-based antenna such as the Luneburg lens antenna. The Luneburg lens is a spherical-shaped graded dielectric structure in which electromagnetic energy from a feed source placed on one surface of the lens radiates as plane wave from the opposite surface of the sphere. This focusing nature of the Luneburg lens allows it to be used as wide-angle beam scanning antenna element for multifunctional wideband antenna applications and beam scanning is simply achieved by switching between an array of antenna feeds placed along the lens’s surface. The benefits include high antenna gain, broad bandwidth, multiple simultaneous beams and reduced electrical power consumption. In particular, the ability to form multiple simultaneous beams without any mechanical moving parts and the presence of the feed source at the back of the antenna make the Luneburg lens an attractive choice to use as wide-angle, multi-beam, multiband antenna applications such as wireless communications and direction finding.
Although the Luneburg lens offers significant potential benefits over phased array systems and reflector antennas to use as a high gain, multibeam multiband antenna element, the lens in its spherical shape is incompatible for practical antenna applications. The spherical geometry of the Luneburg lens structure poses a significant implementation challenge as it complicates the integration of the standard planar feed sources (e.g. waveguides, antenna arrays, detectors) to the lens’s spherical surface. To eliminate this feed mismatch problem between the spherical Luneburg lens and planar feed elements, a more convenient approach is to use a modified Luneburg lens antenna in which the lens’s spherical feed surface is transformed into a planar surface to successfully integrate the lens with planar feed sources and other external back-end electronics1,3,4. To design such a modified Luneburg lens antenna while maintaining the spherical lens’s original electromagnetic performances, the recently developed transformation optics method has drawn great interests among the antenna and electromagnetic community5,6. Transformation Optics (TO) is an emerging technology which enables to control the propagation of electromagnetic waves inside an electromagnetic structure and has been adopted in many electromagnetic designs1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59 including graded-index (GRIN) lenses1,2,3,4,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29. TO method employs the form-invariance principle of Maxwell’s equations under coordinate transformation and spatially transforms the constitutive parameters (i.e. permittivities and permeabilities) of an electromagnetic structure which goes through some level of geometric modifications5.
However, the material parameters required to implement the transformation optics device are anisotropic with both the electric and magnetic responses (i.e. inhomogeneous permittivity and inhomogeneous permeability materials) and requires the use of resonant metamaterials5. To practically realize such a complex anisotropic material, especially the inhomogeneous permeability magnetic material, is very difficult and an implementation challenge. Besides, the requirement of using metamaterials restricts the device functionality to a narrow frequency band. To alleviate the implementation problem associated with the anisotropic TO-based materials, an approximated concept of transformation optics, called quasi-conformal transformation optics (QCTO), was introduced6. In the QCTO approximation, the anisotropic nature of the TO-based medium is eliminated by approximating the material’s magnetic responses (i.e. inhomogeneous permeability) to that of free space (i.e. µr = 1) while retaining the material’s electric responses (i.e. positive inhomogeneous permittivity material) to achieve the same functionality. The advantages include the reduction of the anisotropic medium into an isotropic medium which makes the device implementation much easier and the absence of resonant metamaterials which allows the practically realized device to operate over broad frequency band. It is worth mentioning that the quasi-conformal mapping is limited in two-dimensional configurations and have been widely adopted in antenna applications1,2,3,4,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59. For example, a two-dimensional modified Luneburg lens using QCTO method was demonstrated in the X-band3. A method to extend the two-dimensional QCTO method to design three-dimensional electromagnetic structure was proposed6 and a three-dimensional realization of QCTO modified Luneburg lens antennas were demonstrated in the Ku-band (12.4–18 GHz) and Ka-band frequency (26–40 GHz)1,4.
While the QCTO method offers significant benefits to implement a modified Luneburg lens antenna with a planar feed surface using all-dielectric materials, this technique is offset by the presence of reflections6 and these reflections arise from the permittivity mismatches between the lens’s planar feed surface and air. In the original transformation optics method, the transformation medium requires both electric and magnetic responses, and the magnetic responses ensure uniform impedance matching and polarization independence. As the magnetic responses are absent in the QCTO method to make the device realization easier, the reflections are simply generated by the electric responses, i.e. inhomogeneous permittivity, achieved in quasi-conformal mapping. To minimize the reflections of the QCTO modified Luneburg lens and improve the antenna gain over a broad frequency band, the feed sources of the modified lens antenna need to be designed very carefully, e.g. implementing dielectrically loaded antenna feed array, to ensure uniform impedance matching and high gain. However, implementing an array of dielectrically loaded antenna feeds will be very difficult due to the inhomogeneous nature of the antenna feed surface’s permittivity profile.
In this work, we show that the reflections present in QCTO method can be mitigated by incorporating a broadband anti-reflective (AR) layer along with the QCTO modified Luneburg lens’s planar excitation surface. Here, we designed a broadband anti-reflective layer and implemented with the modified lens antenna. Like the Luneburg lens structure, the AR layer has a graded-index (GRIN) permittivity distribution which minimizes the impedance mismatches between the QCTO lens antenna and feed sources. The AR layer enabled modified Luneburg lens antenna shows a high aperture efficiency while maintain a relatively high degree of beam scanning over a broad frequency band. To demonstrate the broadband anti-reflective layer enabled new QCTO Luneburg lens design methodology, an example modified lens antenna was designed using quasi-conformal mapping and implemented with the broadband anti-reflective layer to operate in the Ka-band (26–40 GHz). The modified lens antenna was realized using the fused deposition modeling (FDM) based additive manufacturing technique4 to operate in the Ka-band frequency range (26–40 GHz). The electromagnetic performance of the fabricated lens antenna was experimentally measured and compared with the simulated predictions. Through the design of the broadband anti-reflective layer, we were able to mitigate the impedance mismatches present in QCTO modified Luneburg lens antenna and improve the antenna gain values significantly at most of the feed locations along the QCTO modified Luneburg lens’s planar excitation surface.
Results
QCTO modified Luneburg lens antenna design
The Luneburg lens is a spherical shaped graded-index (GRIN) dielectric structure in which the dielectric permittivity values changes radially, expressed as \({\varepsilon }_{r}=2-{\left(r/a\right)}^{2}\); where r is the radial distance from the center of the lens, and a is the radius of the sphere60. To design a modified Luneburg lens antenna, where portion of the lens’s spherical feed surface is transformed into a flat surface, the quasi-conformal transformation optics (QCTO) method was utilized. As QCTO method is restricted in two-dimensional geometry, here, we conducted a quasi-conformal mapping of the two-dimensional Luneburg lens to modify it into a two-dimensional flat-bottom lens. Figure 1a represents the virtual space, a two-dimensional spherical Luneburg lens structure surrounded by the air and Fig. 1b is the physical space representing the two-dimensional modified Luneburg lens. The two lenses have the same boundaries except the region CDE and C′D′E′. The boundary CDE in virtual space is quasi-conformally mapped into the region C′D′E′ in physical space and the mapping was performed in the physical space by solving the inverse Laplace’s equations subject to Dirichlet–Neumann boundary conditions:
The QCTO mapping was carried out numerically using the COMSOL Multiphysics solver and the new material parameters of the modified two-dimensional Luneburg lens were calculated as:
Here, Λ is the Jacobian transformation matrix which relates the coordinate transformation between the physical space and the virtual space. Figure 1a shows the dielectric permittivity distribution of the two-dimensional original Luneburg lens and Fig. 1b presents the calculated permittivity profile of the modified Luneburg lens antenna. The three-dimensional realization of the permittivity profile (Fig. 1c) was achieved by axisymetrically revolving the two-dimensional profile (Fig. 1b) along its center axis.
To demonstrate the electromagnetic performance of the modified Luneburg lens antenna (Fig. 1c), full-wave electromagnetic simulations were conducted, and the lens’s gain patterns and beam-steering angle were calculated at Ka-band (26–40 GHz). To excite the lens, an open-ended waveguide feed was placed at the lens’s flat-bottom surface and the waveguide feed was mechanically moved along the planar surface. To show the beam-steering angle and gain patterns, the lens antenna was excited at five feed locations as shown in Fig. 2a and at each location, the lens’s radiation patterns were calculated using COMSOL™ numerical solver. Figure 2b–f represents the calculated 3D radiation patterns at 30 GHz for the five waveguide feed sources. From the simulated results it is observed that, the lens showed a relatively wide beamscanning angle (from − 55° to + 55°) with a continuously reduced gain value as the feed moves from the outward edges to the center.
The modified Luneburg antenna designed with quasi-conformal mapping was practically realized using fused deposition modeling (FDM) based additive manufacturing (AM) technique4,61. Here, AM is used to generate small scale changes (i.e. less than wavelength) in polymer which results in an effective local permittivity as a function of the local volume fraction of printed material to air. By changing the material volume fraction spatially, the graded permittivity distribution of the QCTO modified Luneburg lens was realized. Figure 3a presents the fabricated QCTO-enabled flat-bottom Luneburg lens antenna and Fig. 3b shows the permittivity variation as a function of volume fraction of the dielectric material. The details description of the fabrication method is described in Ref.4.
To compare the electromagnetic performance of the fabricated modified lens antenna with the simulated predictions, the lens antenna was experimentally characterized by measuring the mismatch losses and the gain patterns as a function of frequency, beam scanning angle and location of the feed source. An open-ended waveguide (WR28) was used as a feed source in the measurement and the waveguide feed was mechanically moved along the planar surface from the outward edge toward the center of the lens. Due to the rotational symmetry of the lens antenna, we are presenting the results at only three feed locations here. Figure 4a compares the simulated and measured gain patterns as a function of beam scanning angle at 30 GHz for the three feed locations (pos − 2, pos − 1, pos 0). It is obvious that the lens showed similar beam-steering performances (0° to − 55°) as the simulated predictions. The rotational symmetry of the Luneburg lens allows similar performance from 0° to + 55°. However, from the measurement and simulation, it is also clear that the quasi-conformally mapped modified Luneburg lens antenna showed a continuous reduction in the maximum gain value as the waveguide feed was moved from the outward edge (pos − 2) toward the center (pos 0) of the lens. This is because of the mismatch losses present in quasi-conformal mapping and the losses are generated by the permittivity mismatches between the modified lens’s planar feed surface and free space. As the permittivity mismatch was highest at the center of the lens (εlens = 2.89 and εair = 1), the reflections were also greater at that location resulting in the lowest gain value. As the permittivity values gradually become lower from the center of the lens toward the outward edges, the mismatch losses start minimizing which increases the gain value. The lens antenna showed a highest gain value at the outward edge (pos − 2) where the permittivity value of the lens’s planar surface is closer to the air. Figure 4b presents the measured reflection coefficients (S11) of the QCTO modified Luneburg lens antenna for the three open-ended waveguide feeds and the free-space waveguide losses without the inclusion of the lens.
In addition to the mismatch losses present in QCTO mapping, it was also observed that the interaction between the higher dielectric constant and the waveguide feed signal results in wider half-power (3 dB) beamwidth which further reduces the lens’s overall gain value significantly. Since, the modified lens antenna had a highest permittivity value at the center (pos 0), the half-power beamwidth became wider at that location (26°) and the beamwidth was lowest at the edge (16°) where the dielectric constant was nearer to the air. Figure 4c demonstrates the measured half-power (3 dB) beamwidth of the QCTO modified Luneburg lens’s radiation patterns at three feed locations (pos − 2, pos − 1, pos 0). Because of the mismatch losses and beam widening, the modified lens antenna showed a lower aperture efficiency (less than 20%) at the center feed location (pos 0) and the aperture efficiency gradually became higher as the feed moved toward the edge (pos − 2) from the center (pos 0). The lens antenna had a highest aperture efficiency of more than 50% at the edge. Figure 4d demonstrates the measured aperture efficiencies of the modified Luneburg lens antenna at three feed locations over the entire Ka-band (26–40 GHz).
Broadband anti-reflective (AR) layer with QCTO modified Luneburg lens
The mismatch losses and half-power beamwidth broadening problem present in QCTO modified Luneburg lens antenna can be mitigated by incorporating an anti-reflective (AR) layer between the modified lens’s planar surface (Fig. 5a) and free space. A quarter-wave long anti-reflective layer is the simplest way to counter the mismatch losses; however, this technique will limit the lens’s functionality to only narrow frequency bands. To minimize the mismatches over broad frequency bands and increase the lens’s gain value at all feed locations, we designed and implemented a broadband anti-reflective layer in conjunction with the QCTO modified Luneburg lens antenna. Like the Luneburg lens, the designed anti-reflective layer has an inhomogeneous permittivity profile which tapers the permittivity values of the modified lens’s flat-bottom surface to that of free space and mitigates the impedance mismatches over a broad frequency band at all feed locations across the planar surface. Besides, the AR layer narrows the half power (3 dB) beamwidth and further increase the lens’s gain value. To design such a broadband anti-reflective layer with a continuously tapered permittivity distribution, we explored the Klopfenstein impedance mitigation method described for microwave transmission lines and implemented the Klopfenstein tapered impedance profile in context of the QCTO modified Luneburg lens’s permittivity distribution. A Klopfenstein profile describes the changes in the characteristic impedances along a microwave transmission line with length L, expressed as62
And the permittivity values required to mimic the Klopfenstein characteristic impedance along the AR layer’s thickness L can be expressed as58,62,63:
Here, εs represents the inhomogeneous permittivity profile of the modified Luneburg lens’s flat-bottom surface (Fig. 5a) and εi is the permittivity value of air (εr = 1). L is the optimum thickness of the anti-reflective layer required to minimize the mismatch losses. The function Φ (x, A) is defined as
where I1 is the first kind modified Bessel function of order one. The maximum reflection (Гm) and initial reflection coefficient (Г0) are defined as7,62:
To implement the anti-reflective layer, the two-dimensional Klopfenstein permittivity profile of the AR layer was calculated using the COMSOL-MATLAB interface and incorporated with the two-dimensional QCTO modified Luneburg lens antenna (Fig. 1b). To ensure a uniform impedance matching at all feed locations and maintain a wide beam scanning angle with high gain value, the optimum thickness of AR layer is very crucial. After conducting several parametric studies, it was found that a λ/2 (at lowest frequency) long anti-reflective layer provides the optimum performance of the modified Luneburg lens antenna in terms of high gain and wide beam scanning angle. Figure 5b presents the calculated two-dimensional permittivity profile of the λ/2 long broadband Klopfenstein anti-reflective layer and Fig. 5c shows the changes in all the permittivity values of the QCTO lens’s bottom surface along the thickness of the AR layer. The two-dimensional AR layer was incorporated with the modified two-dimensional Luneburg lens antenna and Fig. 5d demonstrates the two-dimensional permittivity profile of the AR layer incorporated QCTO modified Luneburg lens antenna. The three-dimensional realization of the permittivity distribution (Fig. 5e) was generated by axisymetrically rotating the two-dimensional profile (Fig. 5d) along its center axis. The broadband anti-reflective layer enabled modified Luneburg lens antenna was fabricated using fused deposition modeling (FDM) based additive manufacturing technique as described in the previous section and Fig. 5f represents the fabricated lens antenna with the broadband anti-reflective layer.
To show the broadband impedance mismatch mitigation and compare the electromagnetic performance, full-wave electromagnetic simulations were conducted at Ka-band using the COMSOL numerical solver. To excite the lens antenna, a waveguide port was used as a feed source at the same five feed locations as used in the QCTO Luneburg lens without the AR layer, along the AR layer’s flat-bottom surface as shown in Fig. 6a. At each location, the far-field radiation pattern was calculated using the COMSOL solver. Figure 6b–f demonstrates the calculated three-dimensional radiation patterns at 30 GHz frequency corresponding to each feed location. From the simulated results, it is evident that the presence of the half-wave long (at 26 GHz) anti-reflective layer mitigates the impedance mismatches and improves the lens’s maximum gain value significantly at most of the feed locations while maintaining the lens’s wide beam scanning angle (± 55°).
The fabricated lens antenna (Fig. 5f) was measured experimentally to compare with the simulated predictions. Figure 6g compares the measured and simulated gain patterns of the AR layer enabled QCTO modified Luneburg lens antenna at 30 GHz frequency at three feed locations (pos -2, pos -1, pos 0). We are presenting the results for three feed locations as the rotational symmetry of the lens antenna allows similar performance at all other feed locations along the entire planar feed surface. From the results, it is obvious that the anti-reflective layer mitigates the mismatch losses present in quasi-conformal mapping and increases the gain value significantly. Additionally, the AR layer’s permittivity profile reduces the half-power (3 dB) beamwidth and increases the lens’ overall gain value. Figure 6h shows the measured half-power (3 dB) beamwidth of the modified lens antenna with and without the presence of AR layer at the center feed location. We are presenting the result for the waveguide feed located at the center as the beamwidth was widest at that location compared to outward edges (Fig. 4c).
Even though the anti-reflective layer mitigates the reflections present in quasi-conformal mapping and increases the lens’ gain value at most of the feed positions, the incorporation of the anti-reflective layer with the QCTO modified Luneburg lens antenna reduces the lens’s maximum gain value at the outward edge feed location (pos − 2). This is because the modified lens antenna without the presence of the AR layer (Fig. 1c) had a minimum permittivity mismatch at the outward edges which resulted in maximum gain value at the edges (pos − 2). As the anti-reflective layer is included with the lens antenna to mitigate the mismatch losses at most of the feed locations (pos − 1, pos 0), the focal point of the lens located at the outward edge (pos − 2) moves away by the AR layer’s thickness and the shift in the focal point at the edge results in scattering and side lobes with a lower gain value.
To show the broadband nature of the designed anti-reflective layer, we measured the gain patterns over the entire Ka-band (26–40 GHz). Figure 7a compares the measured and simulated gain patterns of the lens antennas (i.e. with and without the presence of AR layer) as a function of frequency. For brevity, the results for the center feed location are presented here. From Fig. 7a it is obvious that the designed anti-reflective layer has a broadband impedance mitigation and increases the lens’s gain value over the entire frequency band. These results are consistent at most of the feed locations across the lens’s planar excitation surface except for the outward edges where the lens showed a reduced gain value. Figure 7b compares the measured aperture efficiencies of the modified lens antennas for the feed source located at the center of the lenses over the entire Ka-band. It is evident that the incorporation of the broadband anti-reflective layer with the QCTO modified Luneburg lens antenna enhances the lens’s aperture efficiency significantly from less than 20% to about 60% at the center feed location.
Anti-Reflective layer’s thickness effect on lens’s beam-steering performance
The incorporation of the broadband anti-reflective (AR) layer does mitigate the impedance mismatches and increases the gain value at most of the excitation locations; however, a higher thickness (greater than λ/2) AR layer reduces the lens’s wide beam-scanning angle. For example, in Fig. 8, we designed the QCTO modified Luneburg lens antenna with three different thickness AR layer (i.e. L = λ/2, λ, 1.25*λ). Figure 8(a-c) demonstrates the cross-section view of the permittivity distribution of the lens antenna with anti-reflective layer. Each antenna was excited with a waveguide port at two feed locations and at each location, the gain patterns were calculated at 30 GHz. Figure 8d compares the simulated gain patterns of each of the three lens antennas at two feed locations (pos -2 and pos 0) as a function of the beam-scanning angle. From the simulated results, it is observed that with the increase of the AR layer’s thickness (from λ/2 to 1.25*λ), the lens’s maximum gain value increases significantly (2.5 dBi) for the feed location at the center (pos 0). This is because with the increase of the AR layer thickness, the impedance matching becomes more gradual. However, an increase in the AR layer’s thickness does reduce the lens’s maximum beam scanning angle (6° in this design) when the waveguide feed is located at the outward edges (pos − 2). This is due to the fact that like the Luneburg lens antenna, the anti-reflective layer has a graded-index (GRIN) dielectric profile and with an increase in the thickness, the AR layer starts behaving like a GRIN lens resulting in a reduction in wide beamscanning angle. Also, a higher thickness AR layer does reduce the lens’s maximum gain value at the outward edges (3.4 dBi in Fig. 8d). This is because, an increase in the AR layer’s thickness moves the feed source away from the focal point at the outward edge. But the anti-reflective layer improves the lens’s high gain value and wide beam scanning angle at other feed locations.
Conclusion
In this work, we have showed the design and implementation of a flat-bottom modified Luneburg lens antenna for practical beam scanning antenna applications. The spherical Luneburg lens antenna was modified into a flat-bottom antenna using the quasi-conformal transformation optics (QCTO) method. The modified lens antenna designed with the quasi-conformal mapping suffered from reflection problem due to the permittivity mismatches between the lens’s feed surface and air. Additionally, the interaction of the incident wave on the higher permittivity feed location widens the lens’s half-power (3 dB) beamwidth resulting in further reduction in gain value and aperture efficiency. The broadband anti-reflective layer used in this design mitigates the impedance mismatches significantly over the entire Ka-band and narrows the lens’s half-power (3 dB) beamwidth at the feed location where the permittivity value is higher than the free space.
The only drawback of the design method is that if the anti-reflective layer becomes longer than λ/2 (at lowest frequency), the device’s maximum beam scanning angle starts reducing due to the gradient-index (GRIN) nature of the anti-reflective layer. Also, a higher thickness AR layer reduces the lens’s maximum gain value at the outward edges due to the shift in the lens’s focal point at those locations. However, the anti-reflective layer does improve the lens’s gain value at most of the feed locations except the edges indicating a broadband impedance mitigation at the lens’s planar feed surface. The anti-reflective layer enabled QCTO modified Luneburg lens design method was validated by designing and fabricating a lens antenna designed to operate at Ka frequency band (26–40 GHz). From the measurement and simulated predictions, it was observed that the anti-reflective layer incorporated QCTO modified Luneburg lens antenna showed a wide-angle beam scanning (-55º to + 55º) with high gain value at most of the feed locations. The lens antenna showed a relatively high aperture efficiency at most feed locations compared to the QCTO Luneburg lens antenna without an anti-reflective layer. Implementing the broadband AR layer with the QCTO modified Luneburg lens antenna resulted in an aperture efficiency of more than 60% at most of the feed locations except at the outward edges. The lens antenna showed an aperture efficiency of about 40% at the extreme outward edges due to the shift in lens’s focal point.
In this work, we showed the broadband impedance mitigation method to compensate the reflections present in the quasi-conformally mapped electromagnetic structure and implemented it in the context of the QCTO-enabled gradient-index (GRIN) modified Luneburg lens antenna. We expect that this anti-reflective layer-based new QCTO device design methodology will have practical applicability and can be extended to many other areas of electromagnetic designs28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53 which make use of the quasi-conformal transformation optics (QCTO) method. The incorporation of the broadband anti-reflective layer along with the QCTO designs will improve the device electromagnetic performance significantly and become a robust alternative to the conventional QCTO-based designs which suffer from reflections. Here, we demonstrated the calculation of the proposed anti-reflective layer’s permittivity distribution based on the Klopfenstein impedance taper profile. However, we believe, many other continuously tapered permittivity profiles such as Exponential profile or Gaussian profile can also be exploited to calculate the AR layer’s inhomogeneous permittivity distributions.
Methods
The numerical simulations such as the 2D QCTO mapping was performed by solving the Laplace’s equations using COMSOL Mathematics module. The calculation of the QCTO permittivity distribution and the first order partial derivatives of the Jacobian transformation matrix was achieved via the COMSOL solver. The calculation and implementation of the anti-reflective layer was performed by using the COMSOL-MATLAB Livelink interface. The 3D full-wave electromagnetic performance of the 3D Luneburg lens antenna was evaluated using COMSOL 3D RF module.
The antenna gain patterns were measured by using an Agilent PNA E83684B vector network analyzer. Here, the transmission coefficients of the lens antenna with respect to a fixed standard gain horn antenna was measured from − 90° to + 90° in 1° increment. To minimize the reflections in the measurement, radar absorbing material was used surrounding the measurement system.
Change history
01 March 2021
A Correction to this paper has been published: https://doi.org/10.1038/s41598-020-77618-6
References
Ma, H. F. & Cui, T. J. Three-dimensional broadband and broad-angle transformation-optics lens. Nat. Commun. 1, 124 (2010).
Lei, J. et al. Experimental demonstration of conformal phased array antenna via transformation optics. Sci. Rep. 8, 3807 (2018).
Kundtz, N. & Smith, D. R. Extreme-angle broadband metamaterial lens. Nat. Mater. 9, 129–132 (2010).
Biswas, S. et al. Realization of modified Luneburg lens antenna using quasi- conformal transformation optics and additive manufacturing. Microw. Opt. Technol. Lett. 61, 1022–1029 (2019).
Pendry, J. B., Schurig, D. & Smith, D. R. Controlling electromagnetic fields. Science 312, 1780–1782 (2006).
Landy, N. I., Kundtz, N. & Smith, D. R. Designing three-dimensional transformation optical media using quasiconformal coordinate transformations. Phys. Rev. Lett. 105, 193902 (2010).
Biswas, S. Design and additive manufacturing of broadband beamforming lensed antennas and load bearing conformal antennas. PhD Thesis, University of Delaware (2019).
Smith, D. R., Urzhumov, Y., Kundtz, N. B. & Landy, N. I. Enhancing imaging systems using transformation optics. Opt. Express 18, 21238–21251 (2010).
Jiang, Z. H., Turpin, J. P., Morgan, K., Lu, B. & Werner, D. H. Spatial transformation-enabled electromagnetic devices: from radio frequencies to optical wavelengths. Phil. Trans. R. Soc. A 373, 20140363 (2015).
Liu, Y., Zentgraf, T., Bartal, G. & Zhang, X. Transformational plasmon optics. Nano Lett. 10, 1991–1997 (2010).
Hunt, J. et al. Broadband wide angle lens implemented with dielectric metamaterials. Sensors 11, 7982–7991 (2011).
Mei, Z. L., Bai, J. & Cui, T. J. Experimental verification of a broadband planar focusing antenna based on transformation optics. New J. Phys. 13, 063028 (2011).
Driscoll, T. et al. Performance of a three dimensional transformation-optical-flattened Luneburg lens. Opt Express 20, 13262–13273 (2012).
Liua, Y. & Zhang, X. Recent advances in transformation optics. Nanoscale 4, 5277 (2012).
Werner, D. H. et al. Gradient-index lens design with quasi-conformal transformation optics for energy concentration. Proc. SPIE 8834, 88340F (2013).
Biswas, S & Mirotznik, M. S. Customized shaped Luneburg lens design by additive fabrication. 18th International Symposium on Antenna Technology and Applied Electromagnetics (ANTEM), pp. 1–2 (2018).
Wu, L., Tian, X., Ma, H., Yin, M. & Li, D. Broadband flattened Luneburg lens with ultra-wide angle based on a liquid medium. Appl. Phys. Lett. 102, 074103 (2013).
Jiang, W. X., Cui, T. J., Ma, H. F., Yang, X. M. & Cheng, Q. Layered high-gain lens antennas via discrete optical transformation. Appl. Phys. Lett. 93, 221906 (2008).
Li, Y. & Zhu, Z. Luneburg lens with extended flat focal surface for electronic scan applications. Opt. Express 24, 7201–7211 (2016).
Jain, S., Mittra, R. & Pandey, S. Flat-base broadband multibeam Luneburg lens for wide-angle scan. J. Electromagn. Waves Appl. 29, 1329–1341 (2015).
Arigong, B., Zhou, R., Kim, H., Lin, Y. & Zhang, H. Plasmonic slot nano-waveguides with flattened Luneburg lens-based optical couplers. Proc. SPIE 8988, 89881L (2014).
Mei, Z. L., Bai, J. & Niu, T. M. A planar focusing antenna design using quasi-conformal mapping. Prog. Electromagn. Res. M 13, 261–273 (2010).
Gao, J., Wang, C., Zhang, K., Hao, Y. & Wu, Q. Beam steering performance of compressed Luneburg lens based on transformation optics. Results in Phys. 9, 570–575 (2018).
Biswas, S. & Mirotznik, M. 3D modeling of transformation optics based flattened Luneburg lens using Comsol multiphysics modeling software. Comsol Conference. 1–1 (2018).
Liu, K., Ghasemifard, F. & Teruel, O. Q. Broadband Metasurface Luneburg Lens Antenna Based on Glide-Symmetric Bed of Nails. 11th European Conference on Antennas and Propagation (EUCAP). (2017)
Su, Y. & Chen, Z. N. A flat dual-polarized transformation-optics beamscanning Luneburg lens antenna using PCB-stacked gradient index metamaterials. IEEE Trans. Antennas Propag. 66, 5088–5097 (2018).
Zhou, F. et al. Additive manufacturing of a 3D terahertz gradient-refractive index lens. Adv. Opt. Mater. 4, 1034–1040 (2016).
Aghanejad, I., Abiri, H. & Yahaghi, A. High-gain planar lens antennas based on transformation optics and substrate-integrated waveguide (SIW) technology. Prog. Electromagn. Res. C 68, 45–55 (2016).
Ebrahimpouri, M. & Teruel, O. Q. Bespoke lenses based on quasi-conformal transformation optics technique. IEEE Trans. Antennas Propag. 65, 2256–2264 (2017).
Schurig, D. et al. Metamaterial electromagnetic cloak at microwave frequencies. Science 314, 977–980 (2006).
Zheng, B. et al. Concealing arbitrary objects remotely with multi-folded transformation optics. Light Sci. Appl. 5, e16177 (2016).
Liu, R. et al. Broadband ground-plane cloak. Science 323, 366–369 (2009).
Liu, H. L., Zhu, X. Q., Liang, L., Zhang, X. M. & Yang, Y. Tunable transformation optical waveguide bends in liquid. Optica 4, 839–846 (2017).
Wei, P. et al. Metasurface-loaded waveguide for transformation optics applications. J. Opt. 18, 044015 (2016).
Jiang, W. X. et al. Design of arbitrarily shaped concentrators based on conformally optical transformation of nonuniform rational B-spline surfaces. Appl. Phys. Lett. 92, 264101 (2008).
Sadeghi, M. M., Xu, L., Nadgaran, H. & Chen, H. Optical concentrators with simple layered designs. Sci. Rep. 5, 11015 (2015).
Chen, H. et al. Design and experimental realization of a broadband transformation media field rotator at microwave frequencies. Phys. Rev. Lett. 102, 183903 (2009).
Yang, R., Tang, W. & Hao, Y. Wideband beam-steerable flat reflectors via transformation optics. IEEE Antennas Wirel. Propag. Lett. 10, 1290–1294 (2011).
Liang, L. & Hum, S. V. Wide-angle scannable reflector design using conformal transformation optics. Opt. Express 21(2), 2133–2146 (2013).
Kwon, D. H. & Werner, D. H. Polarization splitter and polarization rotator designs based on transformation optics. Opt. Express 16, 18731–18738 (2008).
Shin, D., Urzhumov, Y., Lim, D., Kim, K. & Smith, D. R. A versatile smart transformation optics device with auxetic elasto-electromagnetic metamaterials. Sci. Rep. 4, 4084 (2014).
Dong, H. Y. et al. Realization of broadband acoustic metamaterial lens with quasi-conformal mapping. Appl. Phys. Express 10, 087202 (2017).
Berry, E. A., Cutierrez, J. J. & Rumpf, R. C. Design and simulation of arbitrarily shaped transformation optic devices using a simple finite-difference method. Prog. Electromagn. Res. B 68, 1–16 (2016).
Zhang, P., Jin, Y. & He, S. Inverse transformation optics and reflection analysis for two-dimensional finite-embedded coordinate transformation. IEEE J. Sel. Top. Quantum Electron. 16, 427–432 (2010).
Liu, D., Gabrielli, L. H., Lipson, M. & Johnson, S. G. Transformation inverse design. Opt. Express 21, 14223–14243 (2013).
Chang, Z., Zhou, X., Hu, J. & Hu, G. Design method for quasi-isotropic transformation materials based on inverse Laplace’s equation with sliding boundaries. Opt. Express 18, 6089–6096 (2010).
Tichit, P. H., Burokur, S. N., Germain, D. & Lustrac, A. D. Design and experimental demonstration of a high-directive emission with transformation optics. Phys. Ref. B 83, 155108 (2011).
Campbell, S. D., Nagar, J., Brocker, D. E. & Werner, D. H. On the use of surrogate models in the analytical decompositions of refractive index gradients obtained through quasi conformal transformation optics. J. Opt. 18, 044019 (2016).
Yao, K. & Jiang, X. Designing feasible optical devices via conformal mapping. JOSA B 28, 1037–1042 (2011).
Junqueira, M. A. F. C., Gabrielli, L. H. & Spadoti, D. H. Comparison of anisotropy reduction strategies for transformation optics designs. IEEE Photon. J. 7, 6500110 (2015).
Junqueira, M. A. F. C., Gabrielli, L. H. & Spadoti, D. H. Anisotropy minimization via least squares method for transformation optics. Opt. Express 22, 18490–18498 (2014).
Wu, Qi., Turpin, J. P. & Werner, D. H. Quasi-conformal transformation electromagnetics enabled flat collimating lenses. Proc. Of the IEEE International Symposium on Antennas and Propag. 1–2 (2012).
Morgan, K. L., Brocker, D. E., Campbell, S. D. & Werner, D. H. Transformation-optics-inspired anti-reflective coating design for gradient index lenses. Opt. Lett. 40, 2521–2524 (2015).
He, Y. & Eleftheriades, G. V. Matched, Low-Loss, and Wideband Graded-Index Flat Lenses for Millimeter-Wave Applications. IEEE Trans. Antennas Propag. 66(3), 1114–1123 (2018).
Yi, H., Qu, S. W., Ng, K. B., Chan, C. H. & Bai, X. 3-D Printed Millimeter-Wave and Terahertz Lenses with Fixed and Frequency Scanned Beam. IEEE Trans. Antennas Propag. 64(2), 442–449 (2016).
Chiotellis, N., Zhang, S., Vardaxoglou, Y. C. & Grbic, A. X wave radiator implemented with 3D printed metamaterials. IEEE Trans. Antennas Propag. 1, 1–1 (2020).
Bjorkqvist, O., Zetterstrom, O. & Teruel, O. Q. Additive manufactured dielectric Gutman lens. Electron. Lett. 55(25), 1318–1320 (2019).
Biswas, S., & Mirotznik, M. Quasi-conformal transformation optics (QCTO) enabled modified Luneburg lens design using broadband anti-reflective layer. Comsol Conference. (2019).
Wang, C., Xia, Y., Guo, G., Nasir, M., & Zhu, Q. Ellipsoidal Luneburg lens binary array for wide-angle scanning. IEEE Trans. Antennas Propag. (2020)
Luneburg, R. K. Mathematical Theory of Optics 187 (University of California Press, Berkeley, 1966).
Biswas, S., Larimore, Z. & Mirotznik, M. Additively manufactured Luneburg lens based conformal beamformer. Proc. IEEE Antennas Propag. 1, 1–1 (2018).
Klopfenstein, R. W. A transmission line taper of improved design. Proc. IRE 44, 31–35 (1956).
Grann, E. B., Moharam, M. G. & Pommet, D. A. Optimal design for antireflective tapered two-dimensional subwavelength grating structures. JOSA A 12, 333–339 (1995).
Author information
Authors and Affiliations
Contributions
S.B. developed the concept, designed, and conducted the numerical modeling. S.B. performed the measurement and wrote the manuscript. M.M. supervised the fabrication process.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Biswas, S., Mirotznik, M. High gain, wide-angle QCTO-enabled modified Luneburg lens antenna with broadband anti-reflective layer. Sci Rep 10, 12646 (2020). https://doi.org/10.1038/s41598-020-69631-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-020-69631-6
- Springer Nature Limited
This article is cited by
-
Design and optimization of metamaterial-based highly-isolated MIMO antenna with high gain and beam tilting ability for 5G millimeter wave applications
Scientific Reports (2024)
-
Analytical design of wideband dielectric polygonal directional beam antennas
Optical and Quantum Electronics (2023)
-
High gain, wide-angle QCTO-enabled modified Luneburg lens antenna with broadband anti-reflective layer
Scientific Reports (2020)