Abstract
In this study, cashew nut shells (CNS), waste from a cashew nut processing factory, have been used as an adsorbent for Pb(II) ions in water. Treatments of CNS with 1 M of H2SO4, HNO3, and NaOH solutions were performed to modify their surfaces and improve their adsorption capacities. Characterization of untreated and chemical-treated CNS was carried out using nitrogen adsorption isotherm, elemental (CHN) analysis, Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) equipped with energy dispersive X-ray analysis (EDX). In the study of Pb(II) removal, various models of adsorption kinetics and isotherms were evaluated against the experimental data. The results showed that H2SO4-treated CNS exhibited the highest adsorption capacity. The chemical treatment removes impurities, alters the surface functional groups and improves specific surface areas and pore volumes of native CNS significantly. Surface adsorption and intra-particle diffusion steps were found to substantially affect the overall adsorption process of Pb(II) on H2SO4-treated CNS. Owing to its easy preparation and comparable adsorption capacity, H2SO4-treated CNS has the potential to be developed as a low-cost adsorbent for the removal of Pb(II) from contaminated water.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Introduction
Water is a natural resource necessary for living and sustaining our ecosystem. The increases in human population and industrial processes have released more polluted water into the environment unless proper treatments are implemented effectively. Owing to the water solubility of heavy metals under favorable pH/Eh conditions, water is inevitably contaminated with heavy metals, mostly discharged from several industries1. Such contaminated water leads to environmental problems and accumulation of heavy metals in the food chain which finally returns to human beings. Numerous disorders and diseases are caused by the deposition of heavy metals. Ions of lead, mercury, cadmium and chromium have been reported to be at the top of the toxicity list2.
Lead (Pb) ions contaminated in water are highly toxic to humans and the environment. The sources of lead include the steel and metal alloy industries, welding and electroplating processes, and manufactures of batteries, pigments and ammunition2,3,4. The accumulation of lead in the human body at a certain level can seriously destroy the nervous system, organs (i.e., heart, kidneys, and reproductive system) and tissues5,6. The World Health Organization specifies the maximum concentration of lead ions in drinking water as 0.01 mg/L7.
Several methods have been introduced to remove heavy metal ions from contaminated water such as chemical precipitation, membrane filtration, ion-exchange, electrochemical methods, flotation, and adsorption. Many methods have drawbacks which are high capital and operating costs, the requirement of extra chemicals and high energy, generation of hazardous sludge, and low performance for diluted wastewater8. Among these methods, adsorption is very attractive owing to its easy operation and high efficiency to treat water contaminated with low concentrations of heavy metals, i.e., <100 mg/L7.
In the adsorption process, activated carbon has been widely recognized as an effective adsorbent for the removal of various pollutants contaminated in water. However, the industrial use of activated carbon is limited due to expensive manufacturing and regenerating processes9. To reduce the production and operation costs, there have been continuous attempts to develop low-cost adsorbents derived from industrial and agricultural wastes directly, e.g., cucumber peel5, rapeseed biomass7, cotton stalk and peanut hull9, olive tree pruning waste10, pine tree cone11, and cashew nut shell12. Biomass wastes are promising raw materials since they are increasingly generated.
A disadvantage of using biomass wastes as adsorbents directly is their limited adsorption capacities. To increase the adsorption capacity, chemical treatment (using H2SO4, HNO3, and NaOH) to modify the structure and surface of adsorbents has been adopted13,14,15,16.
The cashew nut processing industry has been growing, particularly in tropical countries such as Brazil, India, and Vietnam17. Cashew nut shell residues are mostly used as solid fuel in factories after extraction of cashew nut shell oil for industrial use. To utilize cashew nut shells efficiently and economically, several studies have been conducted, e.g., the development of cashew nut shells to activated carbons for the adsorption of methylene blue18 and fluoride19. Some researchers investigated the use of raw cashew nut shells as biosorbents for the adsorption of dyes20,21, nickel22, copper23, cadmium24, chromium24, and lead12,24. However, studies on chemical modification of cashew nut shells to improve the adsorption capacity are limited. In this study, therefore, cashew nut shells have been chemically modified, characterized and tested for the adsorption of Pb(II) ions. The aim is to determine and compare the adsorption capacities of chemical (H2SO4, HNO3 or NaOH)-treated cashew nut shells with untreated ones for removal of Pb(II) ions in water. Adsorption kinetics and isotherm were also determined from H2SO4-treated cashew nut shells which gave the greatest adsorption capacity for Pb(II) ions.
Methods
Preparation of cashew nut shell adsorbents
Cashew nut shells (CNS) were collected from a cashew nut processing factory to simply prepare adsorbents of Pb(II) ions. The CNS biomass was initially washed and dried at 105 °C before grinding to a smaller size (<2.0 mm). The ground solid was extracted with hexane to remove cashew nut shell liquid and the remaining shells were dried at 105 °C for 24 h. Portions of the shells were treated with aqueous solutions of H2SO4, HNO3 or NaOH (1 M each) at 30 °C for 24 h and subsequently washed with distilled water several times until the pH of washing water became constant, equal to the original value (pH = 6.9). These chemical-treated adsorbents were then dried at 105 °C for 1 h and kept in a desiccator before use.
During the chemical treatment of CNS, the percentage of weight loss was observed and determined. The weight loss is owing to the damaged structure of CNS, dissolution of some compositions, and operational loss from washing, filtering, and drying stages.
Characterization of cashew nut shell adsorbents
Elemental analysis of untreated and chemical-treated CNS was performed with CHNS/O analyzer (Flash 2000, ThermoScientific, Italy). The C, H, N, and S contents were determined directly, whereas the oxygen content was calculated by the difference between unity and the sum of C, H, N, and S components. Brunauer-Emmett-Teller (BET) specific surface area, pore volume, and average pore diameter of untreated and chemical-treated CNS were determined based on N2 adsorption method at 77 K (ASAP2460, Micromeritics, USA). Before BET analysis, the samples were degassed at 80 °C for 5 h. The surface functional groups of untreated and chemical-treated CNS were determined using Fourier-transform infrared (FTIR) spectroscopy (TENSOR 27, Bruker) recorded in the region of 550–4000 cm−1 with a resolution of 2.0 cm−1. Scanning electron microscopy (SEM) equipped with energy dispersive X-ray analysis (EDX) was performed on Zeiss Merlin VP Compact operated at 2 kV. For each sample, images of the external and internal surfaces were taken at 1000x magnification.
Adsorption study
Batch adsorption was carried out in 500 mL flasks. Typically, an aqueous solution of Pb(NO3)2 was prepared at the initial Pb(II) concentration of 50 mg/L. 2 g of untreated or chemical-treated CNS was added into the flasks. The adsorption temperature was kept constant at 30 ± 1 °C. The adsorption process was initiated by stirring at 500 rpm and continued for 24 h. During the experiment, samples were taken and rapidly centrifuged in order to separate the supernatant liquid from the solid adsorbent. The liquid samples were analyzed with an atomic absorption spectrometer (AAnalyst 800, Perkin Elmer) to determine the remaining concentrations of Pb(II). The adsorption capacities (the amount of Pb(II) adsorbed per unit mass of CNS, qt) were calculated from the initial concentration (C0) and remaining concentration (Ct) of Pb(II) in the aqueous solutions as shown in Eq. (1) where V is the volume of solutions and m is the mass of CNS.
For adsorption kinetics and isotherm studies, the H2SO4-treated CNS which exhibited the highest adsorption capacity for Pb(II) was selected. The initial Pb(II) concentrations were varied between 10 and 50 mg/L. The experiments were conducted in a similar way as described above, and the data at the contact time up to 30 min was used to validate proposed kinetic models (pseudo-first order, pseudo-second order, Elovich, and intra-particle diffusion models). For the adsorption isotherm validation, the data at the equilibrium was used to fit with Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (D-R) isotherm models.
Results and Discussion
Characterization of CNS adsorbents
As shown in Table 1, treatments of CNS with acids (H2SO4, HNO3) and base (NaOH) solutions caused weight loss in the rage of 26.7–51.0%. The treatment with HNO3 gave the largest weight loss (51.0%) whereas the treatment with NaOH resulted in the smallest weight loss (26.7%). The weight loss after chemical treatment is due to the removal of remaining CNS oil and small particles attached to the surface of CNS. Moreover, the components of CNS fiber including its lignocellulosic contents (cellulose, hemicellulose, and lignin), could be hydrolyzed. Acids such as H2SO4 and HNO3 could dissolve hemicellulose components whereas bases such as NaOH promote the lignin destruction25,26. Raw cashew nut shells had crude fiber content of 23.05%, cellulose 11.50%, hemicellulose 7.35% and lignin 7.45%27. The oil composition in cashew nut shells was 8.30%28. Using hexane as an extracting solvent was not able to extract CNS oil completely. A previous study in the treatment of olive tree pruning with H2SO4, HNO3, and NaOH found similar weight loss in the range of 27.5–46.7%10.
Elemental analysis of untreated CNS and chemical-treated CNS gave the result as shown in Table 1. The C content of untreated CNS in this study was 45.93%, which is in agreement with the range (45.21–58.3%) reported in the previous literature23,29,30,31,32. The difference in the composition of CNS depends on the varieties and growing condition of cashew nut trees. It is important to note that oxidation could take place when CNS was treated with chemicals. As a result, the O/C ratios of all chemical-treated CNS were found to increase (with the decrease of C and increase of O contents) compared to untreated CNS. Chemical oxidation was reported to occur with HNO3 and H2SO4 treatments33.
BET specific surface area, pore volume, and average pore size of untreated CNS and chemical-treated CNS are summarized in Table 1. Chemical treatment significantly increased the specific surface area and pore volume of raw CNS. The acid treatment was found to improve the pore characteristics of CNS better than the base treatment. H2SO4-treated CNS exhibited the highest values of specific surface area (0.648 m2/g) and pore volume (12.19 ×10–4 cm3/g). NaOH-treated CNS gave the lowest values of specific surface area (0.163 m2/g) and pore volume (0.16 × 10–4 cm3/g). However, the specific surface areas of all chemically treated CNS are not high compared to those of commercial adsorbents.
FTIR spectra of untreated and chemical-treated CNS are shown in Fig. 1. The broad peaks at 3350–3330 cm−1 are assigned to -OH stretches of alcohols and phenols found in the lignocellulosic structure as well as absorbed water. HNO3- and NaOH-treated CNS had lower peak intensities of -OH groups than untreated and H2SO4-treated CNS. For untreated, H2SO4- and HNO3-treated CNS, the double peaks at ~2925 and ~2855 cm−1 could represent C-H stretching of CH2 and CH3 groups (asymmetric and symmetric stretches)10 and their bending vibration at ~1451 cm−1. These peaks were mostly noticed for H2SO4-treated CNS. The sharp peaks at ~1606 cm−1 could be assigned to C=C bonds34. The small peaks at 1711–1717 cm−1 in the spectra of untreated, H2SO4- and HNO3-treated CNS might be associated with C=O stretching of carboxylic acids, ketones, and aldehydes7,34.
In comparison to untreated CNS, sharper peaks were observed at 1028, 1155, and 1207 cm−1 for H2SO4-treated CNS (Fig. 1), suggesting an increase in functional groups with single oxygen bonds, e.g., ethers, esters, alcohols, phenols, and lactones. Peaks between 1000 and 1300 cm−1 indicated C-O stretching of these functional groups13. Similar to our result, the treatment of olive tree pruning waste with H2SO4 increased the peak intensity at 1000–1200 cm−110. For H2SO4-treated CNS, sharper peaks were also found at 1321, 1451, 1606, and 1711 cm−1, compared to untreated and HNO3-treated CNS. The most prominent peaks of H2SO4-treated CNS are expected to play an important role in the increased sorption capacity for lead ions compared to untreated and other chemically-treated CNS as discussed later. For NaOH-treated CNS, intensities of peaks decreased significantly. The reduced intensities are probably due to delignification. Alkaline treatment has been widely reported to remove lignin content significantly35. FTIR spectra of pure lignin exhibited the peaks at ∼3400 cm−1 (-OH group in aromatic and aliphatic structures), 2850–2920 cm−1 (C-H bonds of CH2 and CH3 of propyl side chains), 1650–1720 cm−1 (C=O group), 1510–1600 cm−1 (C=C group in aromatic structure) and 700–1450 cm−1 (C-C and C-H bonds in aromatic structure)36,37. For NaOH-treated CNS, the intensities of peaks at these wavenumbers decreased significantly, confirming the removal of lignin components. Moreover, the collapse of CNS structure with NaOH treatment indicated the dissolution of lignin, as evidenced by the SEM image in Fig. 2d (right). Lignin is a major constituent providing strength to plant cell walls. Similar to our result, increasing the concentration of NaOH in the treatment process was reported to reduce peaks intensities in FTIR spectra11.
The lower peaks intensities of NaOH-treated CNS caused fewer numbers of active functional groups necessary for the binding of lead ions. As can be seen from Table 1, specific surface areas of CNS are improved with all chemical treatments but still low. Therefore, it is expected that the interaction between lead ions and surface functional groups of the adsorbent is more important than physical factors (i.e., specific surface area) for the removal of lead ions from water.
The external and internal surface structures of untreated and chemical (H2SO4, HNO3, or NaOH)-treated CNS are shown in Fig. 2. Chemical treatment changes the surface texture of CNS. Untreated CNS has numerous irregular and small particles attached to both the external and internal surfaces. The treatment of CNS with all types of chemicals could wash out these particles from the surfaces, leaving smoother surfaces. The texture of CNS was damaged with HNO3 and H2SO4 treatments; as a result, significant shrinkage and more porous structure were noticed. These, in turn, generated a more specific surface area for the adsorption process. These results are in agreement with the result obtained from BET surface area analysis (Table 1). The treatment with NaOH also alters the texture of raw CNS but to a greater extent than the treatment with acids (Fig. 2). It is generally known that NaOH could break down the internal structure, particularly lignin of lignocellulosic materials. However, the number of voids in the structure of NaOH-treated CNS (Fig. 2d (left)) seems to be less than that of acid-treated CNS.
EDX spectra of untreated and chemical (H2SO4, HNO3, or NaOH)-treated CNS are presented in Fig. 3. Untreated CNS consisted of C, O, K, Mg, Cl, S and P elements. Treatment with H2SO4 significantly removed K, Mg, Cl, and P, leaving the surface with only C, O, and S. Similarly, treatment with a weaker acid (HNO3) removed K, Mg, Cl, and P. However, the presence of Fe and Ca was found owing to the intrinsic composition of CNS. The previous analysis of CNS ash showed the presence of silica, iron oxide, aluminium oxide, calcium oxide, and sodium oxide22,23. EDX spectra are linked to image maps generated by SEM, which is performed at a certain position on the surface of materials. When materials are heterogeneous, EDX analysis could give different results with various positions of SEM images. For NaOH treatment, the replacement of Cl and P with Na and Ca was noticed. Na might come from NaOH solution and intrinsic composition of CNS. Overall, elements were removed from the structure of CNS mostly by H2SO4, followed by HNO3 and NaOH treatments. Although the cationic elements (i.e., Na, K, Ca, and Mg) of the adsorbent were reported to increase lead adsorption38, it is not valid for this study. Other factors are influencing the adsorption of Pb(II) such as porosity, specific surface area and, most importantly, surface functional groups of the adsorbent.
Adsorption study: effect of chemical treatment
The adsorption capacities of untreated and chemical (H2SO4, HNO3, or NaOH)-treated CNS for Pb(II) are shown in Fig. 4. All the adsorption processes took place very quickly at the beginning (1 min of contact time) because many active sites are available for lead ions to adsorb. All chemical treatment could significantly improve the adsorption capacity of CNS. Adsorption equilibrium was attained after 24 h of contact time. The treatment of CNS with H2SO4 gave the highest adsorption capacity (8.30 mg/g), followed by those treated with HNO3 (6.39 mg/g) and NaOH (3.22 mg/g). The untreated CNS gave the equilibrium adsorption capacity only 2.08 mg/g.
The highest adsorption capacity of H2SO4-treated CNS could be related to the prominent C=O and C-O bonds found by FTIR analysis. The H2SO4 treatment was reported to alter the surface oxygen group species of activated carbon39. Moreover, the specific surface area and pore volume of H2SO4-treated CNS were the greatest among all chemically treated CNS (see Table 1).
HNO3-treated CNS gave higher lead adsorption capacity than NaOH-treated CNS. The higher adsorption capacity is probably due to the higher number of active functional groups as indicated by FTIR spectra. The specific surface area and pore volume of HNO3-treated CNS were also higher than NaOH-treated CNS (see Table 1). Therefore, it can be concluded that both chemical (i.e., surface functional groups) and physical (i.e., specific surface area and pore volume) factors are required for the adsorption capacity of lead ions on CNS.
NaOH-treated CNS gave higher lead adsorption capacity than untreated CNS although its FTIR spectrum exhibited lower intensity peaks. This result suggests that there are other factors than surface functional groups influencing the adsorption process. Physical factors (i.e., the removal of surface impurities and disintegration of fiber to generate more specific surface area) must be taken into account. Impurities attached to the surface or structure of CNS could inhibit the sorption of lead ions. As evidenced by EDX analysis (Fig. 3), H2SO4 treatment removes elements the best, followed by HNO3 and NaOH treatments. This is in agreement with the results of lead adsorption capacities (H2SO4 > HNO3 > NaOH). Hydrolysis reaction could take place with acid treatment more easily than base treatment, causing greater dissolution of organic substances and a severe disintegration of CNS fiber, as indicated by higher weight loss (Table 1). The H2SO4 treatment was previously found to improve the microporous surface area and volume of activated carbon39.
Effect of the initial concentration of Pb(II)
Since H2SO4-treated CNS gave the highest adsorption capacity for Pb(II), it was selected as an adsorbent for further study in the adsorption kinetics and isotherm. The adsorption capacities of H2SO4-treated CNS were found to increase when the initial concentrations of Pb(II) solutions were increased from 10 to 50 mg/L (Fig. 5). However, the increased adsorption capacities were not linearly proportional to the initial concentrations, particularly at the high concentrations (40 and 50 mg/L). This is due to the limited surface area or active sites of the adsorbent. At low concentrations, there are sufficient active sites to adsorb Pb(II). The increased amount of Pb(II) could be supported by many unoccupied active sites. However, when the amount of Pb(II) in the solution is in excess, all Pb(II) species could not be adsorbed on the limited active sites of the adsorbent.
Adsorption kinetics
Adsorption process involves mass transfer (both film and pore diffusions) and surface reaction (the attachment of adsorbate species on the active sites of adsorbent). Simple kinetic models, therefore, cannot be used to explain the process completely. In this study, pseudo-first order, pseudo-second order, Elovich, and intra-particle diffusion models were used to fit the experimental data to explain the adsorption process of Pb(II) on H2SO4-treated CNS.
Pseudo-first order model
The pseudo-first order model assumes that the adsorption capacity is directly proportional to the difference between the equilibrium concentration and concentration at any contact time40. In other words, the rate of occupation of adsorbent sites directly depends on the number of unoccupied sites11. The pseudo-first order equation was derived based on the assumption of physisorption control41. The linearized equation of pseudo-first order model is shown in Eq. (2).
qe (mg/g) is the adsorption capacity at the equilibrium whereas qt (mg/g) is the adsorption capacity at contact time t (min). k1 (min−1) is the first-order rate constant. The application of the pseudo-first order model to the experimental data is shown in Fig. 6(a) from which the values of qe and k1 were determined from the intercepts and slopes of the plots (Table 2). The calculated values of qe from pseudo-first order model were compared with those determined experimentally. The correlation coefficients (R2) were determined and found to be 0.9804–0.9963 for all initial concentrations of Pb(II). The R2 values indicate the validation of pseudo-first order model for explaining the adsorption of Pb(II) on H2SO4-treated CNS. The values of k1 were found to depend on the initial concentrations of Pb(II) at 10–20 mg/L; therefore, the adsorption is a surface reaction rate controlled process at low concentrations. However, the values of k1 decreased and were independent of the initial concentrations of Pb(II) at higher concentrations (30–50 mg/L). This suggests that mass transfer resistance becomes more important at higher concentrations.
Pseudo-second order model
On the basis of the chemical adsorption process, the pseudo-second order model was developed42. The pseudo-second order model describes the initial attachment of adsorbates to form a monolayer, with the possible formation of other layers by physisorption4. The linearized equation of pseudo-second order model is shown in Eq. (3) in which k2 (g/mg/min) is the rate constant of pseudo-second order. The initial adsorption rate, h (mg/g/min), is defined in Eq. (4).
The application of the pseudo-second order model to the experimental data is shown in Fig. 6(b) from which the values of qe, k2 and h were determined from the intercepts and slopes of the plots (Table 2). The R2 values (0.9003–0.9692) indicate that the pseudo-second order model provides a reasonable fit to the experimental data. However, in comparison to the pseudo-first order model, the R2 values were lower. In addition, a larger difference in qe values determined from the pseudo-second order model and experiment were noticed. Therefore, the adsorption of Pb(II) onto H2SO4-treated CNS obeys the Lagergren pseudo-first order kinetic model.
Elovich model
The Elovich model explaining the chemisorption process for the heterogeneous system was first applied to the gas-solid system43,44. The linearized equation of the Elovich model is shown in Eq. (5). In this model, α (mg/g/min) represents the initial adsorption rate constant whereas β (g/mg) represents the desorption constant concerning the surface coverage and the activation energy of the chemisorption process. The application of the Elovich model to the experimental data is shown in Fig. 6(c) from which the values of α and β were determined from the intercepts and slopes. The low R2 values (Table 2) imply the invalidity of the Elovich model for the adsorption of Pb(II) on H2SO4-treated CNS.
Intra-particle diffusion model
As shown in Eq. (6), the intra-particle diffusion model45 is typically used to explain the importance of the diffusion process of adsorbate molecules into the porous structure of adsorbent. kint (mg/g.min−0.5) is the intra-particle rate constant and C (mg/g) is related to the boundary layer thickness. Both values were determined from the slopes and intercepts of the plots between qt and t1/2 as shown in Fig. 6(d). As shown in Table 2, the high R2 values (>0.95) show a good fit, suggesting the suitability of this model and the importance of intra-particle diffusion. However, the intercepts of the plots do not pass through the origin (Fig. 6d) suggesting that intra-particle diffusion is not the sole rate-limiting step46 for the adsorption of Pb(II) on H2SO4-treated CNS. The intra-particle diffusion solely controls the overall adsorption process only when the intercept of the plot between qt and t1/2 is zero34. Moreover, when the intercept becomes higher, the boundary layer effect is more important6,47.
The R2 values and kinetic parameters, according to the models described above are summarized in Table 2. Overall, the R2 values of the pseudo-first order are higher than those of the pseudo-second order model. The calculated values of qe from the pseudo-first order model were closer to the experimental values than the pseudo-second order model. The pseudo-first order model was derived based on the assumption of physisorption control41. The R2 values of the Elovich model, which explains chemisorption process were found to be lower than those obtained from the pseudo-first and pseudo-second order models. These imply that the adsorption of Pb(II) onto the surface of H2SO4-treated CNS is rather physisorption than chemisorption process. Moreover, the R2 values of the intra-particle diffusion model were high (>0.98) at many initial concentrations of Pb(II), which suggests that intra-particle diffusion is as essential as surface adsorption (which is physisorption rather than chemisorption) and cannot be neglected.
Adsorption isotherms
The adsorption equilibrium data obtained from varying the initial concentrations of Pb(II) were analyzed according to Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherms.
Langmuir isotherm
The Langmuir isotherm describes the ideal situation in which the attachment of adsorbates onto a homogenous surface of the adsorbent is monolayer without interaction between the adsorbates48. The adsorption energy of each adsorbate is identical and independent of the adsorbent surface. The linearized form of the Langmuir isotherm is shown in Eq. (7) in which qmax (mg/g) and b (l/mg) represent the monolayer (maximum) adsorption capacity and energy of adsorption, respectively. Both values were determined from the slope and intercept of the plot between Ce and Ce/qe (Fig. 7a). A perfect fit of the Langmuir isotherm with the high value of R2 (0.9997) was obtained. The values of qmax and b were 8.734 mg/g and 1.115 L/mg as reported in Table 3. As indicated by the higher value of b, lead ions had stronger interaction with the surface of H2SO4-treated CNS than that of lobeira fruit (b = 0.02 L/mg)3.
An important parameter of the Langmuir isotherm is called separation factor (RL) determined from Eq. (8), in which C0 is the initial concentration of Pb(II). The value of RL could indicate the shape of isotherm and nature of the adsorption process: favorable isotherm (0 < RL < 1), irreversible isotherm (RL = 0), linear isotherm (RL = 1), and unfavorable isotherm (RL > 1). The closer the RL value is to 0, the more favorable is the adsorption process49. In Fig. 8, the values of RL were found to be between 0 and 0.1 at all the initial concentrations of Pb(II) indicating that the adsorption of Pb(II) on H2SO4-treated CNS is favorable. Moreover, when the initial concentration of Pb(II) was increased, the adsorption became more favorable and irreversible, as indicated by the lower values of RL.
According to the Langmuir isotherm, the adsorption behavior of Pb(II) on H2SO4-treated CNS is related to surface coverage (θ) of the adsorbent, as shown in Eq. (9) where K is equilibrium adsorption constant. The plot of the surface coverage with the initial concentrations of Pb(II) is shown in Fig. 8. When the initial concentration was increased, the surface of the H2SO4-treated CNS was more covered with the attached atoms of Pb(II). At the initial concentration of Pb(II) of 50 mg/L, the surface coverage was 0.46, which means that the surface still has vacant sites for Pb(II) to adsorb further. However, the adsorption rate tends to decrease at the initial concentration higher than 50 mg/L since the relationship between surface coverage and initial concentration begins to level off.
Freundlich isotherm
The Freundlich isotherm describes the attachment of adsorbate species onto a heterogeneous surface of the adsorbent being either monolayer or multilayer with an interaction between the adsorbate species50. The linearized form of the Freundlich model is presented in Eq. (10). The KF constant indicates the adsorption capacity, while n implies the adsorption effectiveness: favorable adsorption (1 < n < 10)51. Both constants were determined from the intercept and slope of the plot between log qe and log Ce (Fig. 7b). As shown in Table 3, the KF and n values were 4.094 (mg/g)(L/mg)1/n and 3.385, respectively. The value of n is higher than unity suggesting easy separation and favorable adsorption of Pb(II) on H2SO4-treated CNS. The R2 value using the Freundlich model was found to be lower than 0.95, suggesting that the adsorption surface of H2SO4-treated CNS deviated from the heterogeneous surface. Owing to the very high value of R2 using the Langmuir isotherm, it could be interpreted that the surface of H2SO4-treated CNS was rather homogeneous.
Temkin isotherm
The adsorbate-adsorbent interaction is taken into account when the Temkin isotherm is used to explain the adsorption process. Such interaction causes a linear decrease in the heat of adsorption of all molecules in the layer with the increasing coverage3. The Temkin model is different from the Freundlich model in which the reduction in the heat of adsorption is linear, not logarithmic, as reported in the Freundlich isotherm5,22. The linearized form of the Temkin isotherm is shown in Eq. (11) where B = RT/b is a constant related to the heat of adsorption, R is the gas constant (8.314 J/mol/K), and AT (L/mg) is a Temkin binding constant. The values of AT (20.087 L/mg) and b (1.681 kJ/mol) were determined from the intercept and slope of the plot between qe and ln Ce (Fig. 7c). When the bonding energy value is low, e.g., <8 kJ/mol, weak adsorbate-adsorbent interaction is formed and the adsorption mechanism mainly involves the physical adsorption3. Based on the value of b (1.681 kJ/mol), it can be concluded that the adsorption of Pb(II) on H2SO4-treated CNS is rather a physisorption. The result is in agreement with the value of n (n > 1), suggested by the Freundlich equation. Moreover, the heat of adsorption of Pb(II) on various adsorbents was previously found to be low, e.g., adsorption of Pb(II) onto banana peels52.
Dubinin-Radushkevich (D-R) isotherm
The Dubinin-Radushkevich isotherm is used to explain the adsorption process on a heterogeneous and porous surface with variable parameters34. The linearized form of the Dubinin-Radushkevich isotherm is shown in Eq. (12) where qs (mg/g) is theoretical saturation capacity, β (mol2/J2) is a constant related to adsorption energy, and ε is the Polanyi potential relating to the equilibrium concentration as shown in Eq. (13). The plot between ln qe and ε2 is shown in Fig. 7(d) from which qs (7.33 mg/g) and β (9×10–8 mol2/J2) were determined from the intercept and slope. The constant β is used to calculate the mean free energy (E) of adsorption of adsorbates based on Eq. (14). The value of E can indicate the type of adsorption process: physical adsorption (E < 8 kJ/mol) and chemical adsorption (E > 8 kJ/mol)9,51. The value of E in this study was found to be 2.36 kJ/mol, suggesting that the adsorption of Pb(II) on H2SO4-treated CNS is physisorption. This is in agreement with the result obtained from the application of the Temkin model to the experimental data.
As summarized in Table 3, the Langmuir isotherm gave the best fit to the experimental data compared to other isotherms. The highest R2 value (0.9997) was obtained. This implies that the adsorption of Pb(II) on the homogeneous surface of H2SO4-treated CNS is monolayer and favorable.
According to the Langmuir isotherm, the maximum adsorption capacity of Pb(II) on H2SO4-treated CNS was 8.734 mg/g. The comparison in the maximum adsorption capacity of this study with previous researches is summarized in Table 4. Since the adsorption conditions are not identical, direct comparison could not be made. However, the maximum adsorption capacity of H2SO4-treated CNS is comparable to that of various biosorbents reported in the earlier literature. Under similar conditions (adsorbent loading, Pb(II) concentration, and temperature), the qmax value of H2SO4-treated CNS was of the same order of magnitude as of biosorbents derived from agricultural wastes such as cedar leaf ash53, peanut shell54, pomelo peel55, soya bean seed56, and mushroom biomass57. At the same adsorbent loading (4 g/L), H2SO4-treated CNS gave higher value of qmax than the adsorbents derived from plum and apricot kernels1. When the kernels were further developed to biochars by thermochemical process, the values of qmax increased significantly. However, such process is complicated, consumes extra energy, and requires further investment. Another crucial factor affecting the value of qmax is adsorption temperature. Adsorption capacity typically decreases with increasing temperature. As shown in Table 4, Pb(II) adsorption by H2SO4-treated CNS was carried out at higher temperature than most adsorbents. At temperatures below 30 °C; therefore, higher values of qmax would be obtained for H2SO4-treated CNS. Based on the comparable adsorption capacity with various biosorbents, H2SO4-treated CNS has the potential to be practically used for the treatment of Pb(II) in contaminated water.
Conclusions
Chemical treatment of CNS significantly improves its adsorption capacity for Pb(II) in water. Chemical treatment not only alters the functional groups but also eliminates impurities attached to the surface or structure of CNS. Moreover, the porous structure of the raw CNS is significantly improved. As a result, specific surface area and pore volume are increased.
Different chemicals give adsorbents with varying adsorption capacities for Pb(II). H2SO4-treated CNS exhibited the highest adsorption capacity, followed by HNO3-treated CNS and NaOH-treated CNS. Acids treatment was found to generate better adsorbents than base treatment in terms of surface functional groups and specific surface area.
Pseudo-first order and intra-particle diffusion models explained the adsorption kinetics of Pb(II) on H2SO4-treated CNS very well. This suggests the importance of intra-particle diffusion step as well as the surface adsorption. The adsorption isotherm was best described with the Langmuir model. Since H2SO4-treated CNS could be prepared easily and its maximum adsorption capacity was comparable to various biosorbents reported in the previous literature, it is, therefore, a promising low-cost adsorbent for removal of Pb(II) from contaminated water.
References
Pap, S. et al. Synthesis of highly-efficient functionalized biochars from fruit industry waste biomass for the removal of chromium and lead. J. Mol. Liq. 268, 315–325 (2018).
Farooq, U., Kozinski, J. A., Khan, M. A. & Athar, M. Biosorption of heavy metal ions using wheat based biosorbents – a review of the recent literature. Bioresour. Technol. 101, 5043–5053 (2010).
Araújo, C. S. T. et al. Elucidation of mechanism involved in adsorption of Pb(II) onto lobeira fruit (Solanum lycocarpum) using Langmuir, Freundlich and Temkin isotherms. Microchem. J. 137, 348–354 (2018).
Schwantes, D. et al. Chemical modifications on pinus bark for adsorption of toxic metals. J. Environ. Chem. Eng. 6, 1271–1278 (2018).
Basu, M., Guha, A. K. & Ray, L. Adsorption of lead on cucumber peel. J. Clean. Prod. 151, 603–615 (2017).
Nadeem, R., Ansari, T. M., Akhtar, K. & Khalid, A. M. Pb(II) sorption by pyrolysed Pongamia pinnata pods carbon (PPPC). Chem. Eng. J. 152, 54–63 (2009).
Morosanu, I., Teodosiu, C., Paduraru, C., Ibanescu, D. & Tofan, L. Biosorption of lead ions from aqueous effluents by rapeseed biomass. New Biotechnol. 39, 110–124 (2017).
Nguyen, T. A. H. et al. Applicability of agricultural waste and by-products for adsorptive removal of heavy metals from wastewater. Bioresour. Technol. 148, 574–585 (2013).
Ding, M., Hu, X., Zimmerman, A. R. & Gao, B. Sorption and cosorption of lead (II) and methylene blue on chemically modified biomass. Bioresour. Technol. 167, 569–573 (2014).
Calero, M., Pérez, A., Blázquez, G., Ronda, A. & Martín-Lara, M. A. Characterization of chemically modified biosorbents from olive tree pruning for the biosorption of lead. Ecol. Eng. 58, 344–354 (2013).
Ofomaja, A. E. & Naidoo, E. B. Biosorption of lead(II) onto pine cone powder: studies on biosorption performance and process design to minimize biosorbent mass. Carbohyd. Polym. 82, 1031–1042 (2010).
Siripatana, C., Khuenpetch, A., Phromrak, R., Saengngoen, W. & Nuithitikul, K. Kinetic study of adsorption of lead (II) ions onto cashew nut shells. J. Eng. Appl. Sci. 12, 1819–1824 (2017).
Abdolali, A. et al. Characterization of a multi-metal binding biosorbent: chemical modification and desorption studies. Bioresour. Technol. 193, 477–487 (2015).
Ayyappan, R., Sophia, A. C., Swaminathan, K. & Sandhya, S. Removal of Pb(II) from aqueous solution using carbon derived from agricultural wastes. Process Biochem. 40, 1293–1299 (2005).
Mashkoor, F. & Nasar, A. Preparation, characterization and adsorption studies of the chemically modified Luffa aegyptica peel as a potential adsorbent for the removal of malachite green from aqueous solution. J. Mol. Liq. 274, 315–327 (2019).
Islam, M. T. et al. Removal of methylene blue and tetracycline from water using peanut shell derived adsorbent prepared by sulfuric acid reflux. J. Environ. Chem. Eng. 7, 102816 (2019).
Oliveira, E. M. S. et al. Performance of (in)active anodic materials for the electrooxidation of phenolic wastewaters from cashew-nut processing industry. Chemosphere 201, 740–748 (2018).
Spagnoli, A. A., Giannakoudakis, D. A. & Bashkova, S. Adsorption of methylene blue on cashew nut shell based carbons activated with zinc chloride: the role of surface and structural parameters. J. Mol. Liq. 229, 465–471 (2017).
Alagumuthu, G. & Rajan, M. Equilibrium and kinetics of adsorption of fluoride onto zirconium impregnated cashew nut shell carbon. Chem. Eng. J. 158, 451–457 (2010).
Senthil Kumar, P. et al. Adsorption of dye from aqueous solution by cashew nut shell: Studies on equilibrium isotherm, kinetics and thermodynamics of interactions. Desalination 261, 52–60 (2010).
Subramaniam, R. & Ponnusamy, S. K. Novel adsorbent from agricultural waste (cashew nut shell) for methylene blue dye removal: optimization by response surface methodology. Water Resour. Ind. 11, 64–70 (2015).
Senthil Kumar, P. et al. Adsorption behavior of nickel(II) onto cashew nut shell: equilibrium, thermodynamics, kinetics, mechanism and process design. Chem. Eng. J. 167, 122–131 (2011).
Senthil Kumar, P., Ramalingam, S., Sathyaselvabala, V., Kirupha, S. D. & Sivanesan, S. Removal of copper(II) ions from aqueous solution by adsorption using cashew nut shell. Desalination 266, 63–71 (2011).
Coelho, G. F. et al. Removal of metal ions Cd (II), Pb (II), and Cr (III) from water by the cashew nut shell Anacardium occidentale L. Ecol. Eng. 73, 514–525 (2014).
Alvira, P., Tomás-Pejó, E., Ballesteros, M. & Negro, M. J. Pretreatment technologies for an efficient bioethanol production process based on enzymatic hydrolysis: a review. Bioresour. Technol. 101, 4851–4861 (2010).
Mosier, N. et al. Features of promising technologies for pretreatment of lignocellulosic biomass. Bioresour. Technol. 96, 673–686 (2005).
Ocheja, J. O., Lablabe, B. C., Oguche, H. G. E. & Usman, G. O. Vitamin composition and fibre fractions of cashew nut shell: implication for animal nutrition. Pakistan J. Nutr. 14, 252–254 (2015).
Singh, R. N., Jena, U., Patel, J. B. & Sharma, A. M. Feasibility study of cashew nut shells as an open core gasifier feedstock. Renew. Energy 31, 481–487 (2006).
Das, P. & Ganesh, A. Bio-oil from pyrolysis of cashew nut shell-a near fuel. Biomass Bioenergy 25, 113–117 (2003).
Gangil, S. Dominant thermogravimetric signatures of lignin in cashew shell as compared to cashew shell cake. Bioresour. Technol. 155, 15–20 (2014).
Tippayawong, N., Chaichana, C., Promwangkwa, A. & Rerkkriangkrai, P. Gasification of cashew nut shells for thermal application in local food processing factory. Energy Sustain. Dev. 15, 69–72 (2011).
Tsamba, A. J., Yang, W. & Blasiak, W. Pyrolysis characteristics and global kinetics of coconut and cashew nut shells. Fuel Process. Technol. 87, 523–530 (2006).
Fan, Q. et al. Effects of chemical oxidation on surface oxygen-containing functional groups and adsorption behavior of biochar. Chemosphere 207, 33–40 (2018).
Ben-Ali, S., Jaouali, I., Souissi-Najar, S. & Ouederni, A. Characterization and adsorption capacity of raw pomegranate peel biosorbent for copper removal. J. Clean. Prod. 142, 3809–3821 (2017).
Singh, J., Suhag, M. & Dhaka, A. Augmented digestion of lignocellulose by steam explosion, acid and alkaline pretreatment methods: A review. Carbohydr. Polym. 117, 624–631 (2015).
Coral Medina, J. D. et al. Lignin preparation from oil palm empty fruit bunches by sequential acid/alkaline treatment – A biorefinery approach. Bioresour. Technol. 194, 172–178 (2015).
Jiang, W. et al. Quantitative analyses of lignin hydrothermolysates from subcritical water and water-ethanol systems. Ind. Eng. Chem. Res. 53, 10328–10334 (2014).
Wongrod, S. et al. Lead sorption by biochar produced from digestates: consequences of chemical modification and washing. J. Environ. Manage. 219, 277–284 (2018).
Pak, S.-H., Jeon, M.-J. & Jeon, Y.-W. Study of sulfuric acid treatment of activated carbon used to enhance mixed VOC removal. Int. Biodeterior. Biodegradation 113, 195–200 (2016).
Lagergren, S. About the theory of so-called adsorption of soluble substances. Kungl. Svenska Vetenskapsakad. Handl. 24, 1–39 (1898).
Liao, S.-W., Lin, C.-I. & Wang, L.-H. Kinetic study on lead (II) ion removal by adsorption onto peanut hull ash. J. Taiwan Inst. Chem. Engrs 42, 166–172 (2011).
Ho, Y. S. & McKay, G. Pseudo-second order model for sorption processes. Process Biochem. 34, 451–465 (1999).
Low, M. Kinetics of chemisorption of gases on solids. Chem. Rev. 60, 267–312 (1960).
Ramachandran, P., Vairamuthu, R. & Ponnusamy, S. Adsorption isotherms, kinetics, thermodynamics and desorption studies of reactive orange16 on activated carbon derived from Ananas comosus (L.) carbom. ARPN J. Eng. Appl. Sci. 6, 15–25 (2011).
Moris, W. J. & Weber, J. C. Kinetics of adsorption on carbon from solutions. J. Saint. Eng. Div. ASCE 89, 31–59 (1963).
Wan Ngah, W. S. & Fatinathan, S. Adsorption characterization of Pb(II) and Cu(II) ions onto chitosan-tripolyphosphate beads: kinetic, equilibrium and thermodynamic studies. J. Environ. Manage. 91, 958–969 (2010).
Kannan, N. & Sundaram, M. M. Kinetics and mechanism of removal of methylene blue by adsorption on various carbons—a comparative study. Dyes Pigments 51, 25–40 (2001).
Langmuir, I. The constitution and fundamental properties of solids and liquids. J. Am. Chem. Soc. 28, 2629 (1916).
Nitzsche, R., Gröngröft, A. & Kraume, M. Separation of lignin from beech wood hydrolysate using polymeric resins and zeolites – determination and application of adsorption isotherms. Sep. Purif. Technol. 209, 491–502 (2019).
Freundlich, H. Over the adsorption in solution. J. Phys. Chem. 57, 1100–1107 (1906).
Meneghel, A. P. et al. Biosorption of cadmium from water using Moringa (Moringa oleifera Lam.) seeds. Water Air Soil. Pollut. 224, 1383 (2013).
Anwar, J. et al. Removal of Pb(II) and Cd(II) from water by adsorption on peels of banana. Bioresour. Technol. 101, 1752–1755 (2010).
Hafshejani, L. D. et al. Removal of zinc and lead from aqueous solution by nanostructured cedar leaf ash as biosorbent. J. Mol. Liq. 211, 448–456 (2015).
OuYang, X. K., Yang, L. P. & Wen, Z. S. Adsorption of Pb(II) from solution using peanut shell as biosorbent in the presence of amino acid and sodium chloride. BioRes. 9, 2446–2458 (2014).
Yu, X. L. & He, Y. Optimal ranges of variables for an effective adsorption of lead(II) by the agricultural waste pomelo (Citrus grandis) peels using Doehlert designs. Sci. Rep. 8, 729 (2018).
Gaur, N., Kukreja, A., Yadav, M. & Tiwari, A. Adsorptive removal of lead and arsenic from aqueous solution using soya bean as a novel biosorbent: equilibrium isotherm and thermal stability studies. Appl. Water Sci. 8, 98 (2018).
Kariuki, Z., Kiptoo, J. & Onyancha, D. Biosorption studies of lead and copper using rogers mushroom biomass ‘Lepiota hystrix’. S. Afr. J. Chem. Eng. 23, 62–70 (2017).
Author information
Authors and Affiliations
Contributions
K.N. designed research, analyzed data, made discussion and wrote the manuscript including tables and figures, R.P. and W.S. conducted experiment.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Nuithitikul, K., Phromrak, R. & Saengngoen, W. Utilization of chemically treated cashew-nut shell as potential adsorbent for removal of Pb(II) ions from aqueous solution. Sci Rep 10, 3343 (2020). https://doi.org/10.1038/s41598-020-60161-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-020-60161-9
- Springer Nature Limited
This article is cited by
-
Study on the Impact of Bio Waste Cashew Nut Shell Powder in the Polyvinyl Alcohol Bio Films
Waste and Biomass Valorization (2024)
-
Innovative approach to dye adsorption: a comparative study of iron impregnated waste human hair-based activated carbon
International Journal of Environmental Science and Technology (2024)
-
Efficient adsorption of Pb(II) ions using novel adsorbent polyacrylamide/coffee ground composite: isotherm, kinetic and thermodynamic studies
Polymer Bulletin (2024)
-
Utilization of cashew nutshell biomass as eco-friendly sound-emitting pyrotechnic formulation to reduce sulfur usage in fireworks
Biomass Conversion and Biorefinery (2024)
-
Green technology approach for heavy metal adsorption by agricultural and food industry solid wastes as bio-adsorbents: a review
Journal of Food Science and Technology (2023)