Abstract
Here we present a detailed theoretical analysis of the interaction between electrons and optical phonons of interface and confined modes in a wurtzite AlN/GaN/AlN quantum well heterostructure based on the uniaxial dielectric continuum model. The formalism describing the interface and confined mode optical phonon dispersion relation, electron–phonon scattering rates, and average group velocity of emitted optical phonons are developed and numerically calculated. The dispersion relation of the interface phonons shows a convergence to the resonant phonon frequencies 577.8 and 832.3 cm−1 with a steep slope around the zone center indicating a large group velocity. At the onset of interface phonon emission, the average group velocity is small due to the large contribution of interface and confined mode phonons with close-to-zero group velocity, but eventually increases up to larger values than the bulk GaN acoustic phonon velocity along the wurtzite crystal c-axis (8 nm/ps). By adjusting the GaN thickness in the double heterostructure, the average group velocity can be engineered to become larger than the velocity of acoustic phonons at a specific electron energy. This suggests that the high group velocity interface mode optical phonons can be exploited to remove heat more effectively and reduce junction temperatures in GaN-based heterostructures.
Similar content being viewed by others
Introduction
GaN-based semiconductors are of great interest in the electronics and optoelectronics communities because they possess large electronic bandgaps (3.4 eV) suitable for fabricating semiconductor lasers with wavelengths in blue and ultraviolet1 as well as electronic devices designed to tolerate high electric fields (3.3 MV/cm) and elevated operating temperatures (700 °C)2. In particular, AlGaN/GaN high electron mobility transistors (HEMTs) are among the most promising devices for high-power applications3. The spontaneous and piezoelectric polarization fields of this heterostructure allow the GaN layer to form a high-density electron channel through which electrons can flow with high saturation velocity (2.5 × 107 cm/s); this is partly due to the optical phonons with high energy (ħωLO = 92 meV) in GaN4. The electron velocity saturation occurs with the onset of emission of these optical phonons and therefore their energy roughly determines the electron saturation velocity according to v0 ≈ [ħωLO/m]1/2, where m is the effective electron mass. Taking a closer look into the material, the large mismatch between the cation and anion masses causes a large splitting between the energies of the optical and acoustic phonon branches which raises the energy of optical phonons5. The drawback associated with these high energy optical phonons is their short interaction time with electrons compared to the long decay time into acoustic phonons. As in common semiconductors, heat in GaN is carried mainly by the long wavelength acoustic phonons6. To remove the excessive heat that is generated in the electron channel by the collision of hot electrons and the lattice (at the rate of ~10 THz)7, the non-equilibrium optical phonons (whose propagation velocity is close to zero) must decay into acoustic phonons. The process is known as the Ridley process8 and the decay time is reported to be ~5 ps which is much longer than the electron interaction time of ~9 fs9. This mismatch between the optical phonon generation rate and the relaxation rate into acoustic phonons results in a large accumulation of optical phonons in a localized region at the channel and eventually causes the electronic properties to degrade10,11.
In this work, we propose a novel phonon engineering technique that portends applications related to reducing the maximum temperature of the localized hotspot in GaN-based devices. To enhance the heat dissipation efficiency, a double heterostructure consisting of AlN/GaN/AlN is introduced to exploit properties of the interface mode optical phonons. Unlike bulk optical phonons, the mixing between available phonon frequencies of AlN and GaN induces an optical phonon mode that possesses a high propagation velocity at the heterointerface. The existence of these optical phonon modes has been corroborated by Raman studies on AlN/GaN superlattices12,13. The introduction of these interface mode phonons provides an extra channel through which heat can be removed. Here, we employ the uniaxial dielectric continuum model to theoretically examine the properties of interface and confined mode optical phonons and their interaction with hot electrons.
Optical Phonon Mode Dispersion In Wurtzite Crystals
In the double heterostructure of interest in this work, which is a GaN quantum well sandwiched by two AlN layers (AlN/GaN/AlN), there exists four distinct classes of optical phonon modes: the interface, confined, half-space, and propagating modes14. Among these four optical phonon modes, the electrons that are confined in the GaN quantum well mostly interact with the interface and confined phonons; the effect of the half-space and propagating modes on the electrons is negligible in this system15. Here, therefore, we only consider the electron scattering with interface and confined mode optical phonons.
In a heterostructure configuration, the available optical phonon modes and the phonon frequencies for each mode are determined by the relation between the dielectric constant functions. The frequency-dependent dielectric functions parallel εz and perpendicular εt to the z-axis are given as16:
where ω is the phonon frequency, ωLz, ωz, ωLt, and ωt are the characteristic frequencies of A1(LO: longitudinal-optical), A1(TO: transverse-optical), E1(LO), and E1(TO) optical phonon modes, respectively. For the AlN/GaN/AlN quantum well, two sets of material parameters are required such that we obtain four dielectric functions, namely ε1z, ε1t, ε2z, and ε2t, where the subscripts 1 and 2 indicate the GaN and AlN, respectively. With ω = 0, the Lyddane-Sachs-Teller relation is recovered and the static dielectric constants are obtained. Throughout this paper, we take the z-axis along the c-axis of the wurtzite crystal [0001] and perpendicular to the heterointerfaces.
The phonon frequencies and dielectric constants for bulk GaN and AlN used in the calculations are listed in Table 117,18. Using these frequency-dependent dielectric functions of bulk GaN and AlN, the phonon frequencies and available phonon modes of the AlN/GaN/AlN quantum well are deduced by the dielectric continuum model. Notice that the phonon frequencies are listed in units of cm−1. In the following calculations, whenever appropriate, they are converted into units of s−1. We assume that the two high-frequency dielectric constants are identical, i.e., \({\varepsilon }_{{\rm{z}}}^{\infty }={\varepsilon }_{{\rm{t}}}^{\infty }={\varepsilon }^{\infty }\)19.
The conditions imposed on the available interface mode optical phonon frequency are
For confined modes, the conditions are
To clearly illustrate the available range of phonon frequencies for each mode, the four dielectric constants as a function of phonon frequency are shown in Fig. 1. The characteristic frequencies of the dielectric functions which define the phonon frequency ranges are indicated by vertical dashed lines. According to the conditions in Eq. (3), the interface phonons are allowed in two phonon frequency intervals, (ω1t, ω2z) and (ω1Lt, ω2Lz). Since the former (latter) interval corresponds to the TO (LO) phonon frequencies of GaN and AlN, we label the phonon modes that lie in this frequency range as TO (LO) interface phonons. These intervals are indicated in the figure as red and blue shaded regions, respectively. Similarly, according to the conditions in Eq. (4), the confined phonons are allowed in two phonon frequency intervals, (ω1z, ω1t) and (ω1Lz, ω1Lt). The characteristic phonon frequencies associated with these intervals are from the TO and LO phonon frequencies of GaN, and hence we label them as TO confined and LO confined phonons. The TO and LO confined phonon frequency ranges are shown in the figure as green and magenta shaded regions, respectively.
Interface modes
The dispersion relations for the symmetric \({q}_{{\rm{S}}}^{{\rm{IF}}}\) and asymmetric \({q}_{{\rm{A}}}^{{\rm{IF}}}\) interface phonon modes are described by20
where \(\alpha =\frac{1}{2}\sqrt{|{\varepsilon }_{{\rm{1t}}}(\omega )/{\varepsilon }_{{\rm{1z}}}(\omega )|}\), \({\xi }_{1}=\sqrt{|{\varepsilon }_{{\rm{1z}}}(\omega ){\varepsilon }_{{\rm{1t}}}(\omega )|}\), \({\xi }_{2}=\sqrt{|{\varepsilon }_{{\rm{2z}}}(\omega ){\varepsilon }_{{\rm{2t}}}(\omega )|}\), and d is the quantum well thickness. The GaN quantum well thickness d is set to a default value of 5 nm in the following calculations unless otherwise specified. The phonon wave vectors \({q}_{{\rm{S}}}^{{\rm{IF}}}\) and \({q}_{{\rm{A}}}^{{\rm{IF}}}\) must be real and positive which implies that symmetric and asymmetric modes are distinguished based on the polarity of ξ1 – ξ2.
The resonant interface phonon frequency is obtained from ξ1 = ξ2. The ωTO,res and ωLO,res are the TO and LO resonant interface frequencies where ξ1 and ξ2 are equal in the TO and LO phonon frequency range, respectively. These frequencies are calculated as ωTO,res = 577.8 cm−1 and ωLO,res = 832.3 cm−1. From the definition of the symmetric and asymmetric phonon wave vectors, the symmetric mode is only defined in the frequency range where ξ1 > ξ2 and the asymmetric mode is only defined in the range where ξ1 < ξ2. Combined with the constraints of the dielectric constants, the symmetric TO interface modes can only be defined in the phonon frequency range (ω1t, ωTO,res) and the symmetric LO modes in the range (ωLO,res, ω2Lz). Similarly, the asymmetric TO interface phonons are only defined in (ωTO,res, ω2z) and the asymmetric LO modes in (ω1Lt, ωLO,res).
Confined modes
The dispersion relations for the symmetric \({q}_{{\rm{S}}}^{C}\) and asymmetric \({q}_{{\rm{A}}}^{C}\) confined phonon modes are described by20
where μ = sign[ε1z(ω)ε2z(ω)] and n is the quantum number for symmetric and asymmetric confined modes.
The interface and confined mode phonon dispersion relations [Eqs (5)–(8)] are shown in Fig. 2. The subscripts A and S indicate asymmetric and symmetric modes, and superscripts IF and C indicate interface and confined modes, respectively. The low frequency modes that are associated with the TO phonon frequencies of GaN and AlN are plotted in (a) and the high frequency modes that are associated with the LO phonon frequencies are plotted in (b). The symmetric modes are shown in dashed lines and asymmetric modes are shown in solid lines for both interface and confined phonons. The characteristic phonon frequencies, which separate the interface modes from the confined modes, and resonant interface phonon frequencies are indicated with horizontal lines. In terms of phonon energy, the LO interface phonon modes \((91.9 < \hslash {\omega }_{{\rm{LO}}}^{{\rm{IF}}} < 110.3\,{\rm{eV}})\) are higher in energy compared to the TO phonon modes (\(69.3 < \hslash {\omega }_{{\rm{TO}}}^{{\rm{IF}}} < 75.8\,{\rm{eV}}\)). The TO and LO resonant interface phonon energies are 71.7 and 103.2 meV, respectively. Compared to interface phonon modes, more than a pair of symmetric and asymmetric confined modes exist in each phonon frequency interval. Here, we only plot two of each symmetric and asymmetric confined modes that mostly contribute to the electron–phonon scattering process. However, in principle, there are an infinite amount of modes available. It should be noted that for the confined modes, the dispersion curves asymptotically approach a characteristic phonon frequency of GaN (i.e., ω1z for TO confined modes and ω1Lt for LO confined modes), whereas for the interface modes the curves approach the resonant frequency with increasing wave vector. This interface phonon dispersion relation gives rise to a phonon emission threshold energy in the electron–phonon scattering process that does not correspond to an energy of the characteristic phonons of either AlN or GaN.
Another important feature in the dispersion relation is that these interface phonon modes have a nonzero slope at the zone center. This indicates that the group velocity vg = dω/dq is nonzero and that optical phonons generated at the interface will not stay where they were generated (as bulk optical phonons do) but will propagate along the interface. Notice that the x-axis is set to the dimensionless product of phonon wave vector q and the quantum well thickness d. Therefore, the group velocity will increase with increasing quantum well thickness due to the stronger dispersion.
Electron–Phonon Scattering Rate
To investigate the electron scattering rate with confined and interface mode phonons, we adapt the expression from ref.15:
with
where m = m*m0, the dimensionless effective mass21 is m* = 0.22, m0 is the electron rest mass, e0 is the elementary charge, and \(N(\omega )=\frac{1}{{e}^{\hslash \omega /{k}_{{\rm{B}}}T}-1}\) is the phonon occupation number. The upper (lower) signs are taken when considering electron absorption (emission) scattering process. The summation over the quantum number n [identical to the ones in Eqs (7) and (8)] is included to consider scattering with all possible symmetric and asymmetric confined mode phonons. For each n, the proper dispersion relation between q and ω should be imposed through Eqs (7) or (8). In our numerical calculation of the scattering rates, we find that a practical number for the upper limit is n = 5; contributions to the electron–phonon scattering rate from confined modes with n larger than 5 are negligible. Also, the symmetric and asymmetric confined modes must be considered separately as the dispersion relations are different from each other. For the case of interface modes, the summation is omitted because only one interface mode exists in a given range of phonon frequency [ω1, ω2].
In the original formula15, where the integral is assessed over the angle θ between the phonon wave vector q and the optical axis c, the lower and upper limits of the integral are set to θ = 0 and 2π. In order to separately calculate the matrix elements of the Fermi golden rule for each phonon mode of uniaxial wurtzite crystals, the formula with the integral over θ is transformed into Eq. (9) where the integral is over ω. Considering the energy and momentum conservation of the electron–phonon scattering process, the limits of the integral over ω may also be transformed according to the relations:
However, noticing that q is also a complex function of ω with different dispersion relations for different phonon modes [Eqs (5)–(8)] and that the integral must be calculated for different electron energies \({E}_{{\bf{k}}}={\hslash }^{2}{{\bf{k}}}^{2}/2m\), it is impractical to solve the nonlinear equation. Alternatively, we include a conditional variable σ to take care of the relation Eq. (12). Since the implications of the argument inside the square root of the denominator of Eq. (9) [χ(k, q, ω)/m] is identical to Eq. (12), we can evaluate the expression χ(k, q, ω) and keep the square root as a real value by imposing Eq. (11). This way, we can simply set the integral limits to the phonon frequencies where the phonon mode of interest is defined. For example, the upper and lower limits are set to ω1 = ω1Lt and ω2 = ω2Lz, respectively, for the case of LO interface phonons.
For the function D(q, ω), depending on the phonon mode of interest it may be expressed as
or
with
where ζ±(α) = (1/2α)(∂ε1t/∂ω) ± 2α(∂ε1z/∂ω), ζ±(β) = (1/2β)(∂ε2t/∂ω) ± 2β(∂ε2z/∂ω), \(\beta =\frac{1}{2}\sqrt{|{\varepsilon }_{2t}(\omega )/{\varepsilon }_{2z}(\omega )|}\), and k1 and k2 are the magnitudes of the electron wave vector inside and outside of the typical finite quantum well. Only the electronic ground state of the quantum well is considered and a conduction band offset of 2.3 eV between AlN and GaN is assumed22.
Group Velocity Of Emitted Optical Phonons
In Eq. (9), the phase (vp = ω/q) and group velocity (vg = dω/dq) of the phonon modes (or its reciprocal) are frequently used in the equation. Given the complex form of the phonon wave vector q, instead of expressing these velocities in a closed form equation, we calculate the velocities numerically. The group velocity is not only a component of the integral but also a crucial factor that describes the behavior of the phonons, and furthermore, the thermal characteristics of the system. Figure 3 shows the group velocity of the interface and confined phonon modes as a function of phonon frequency. As expected by the dispersion relation shown in Fig. 2, the interface mode phonons possess a considerably larger group velocity compared to the confined mode phonons. The largest confined mode group velocity is less than 7 km/s at ω ~ 552 cm−1 (TO mode), whereas the largest interface mode group velocity reaches up to 138 km/s (or 138 nm/ps) at ω = ω1Lt (LO mode). It is easily deduced that if the full spectrum of interface phonon modes can be utilized, the phonons can carry a portion of the generated heat away along the heterointerface. This would be an additional heat transport mechanism, on top of the always existing acoustic phonon heat transport, that can help the system dissipate heat more efficiently.
To better understand the electron interaction with these interface and confined mode phonons, we evaluate Eq. (9) and calculate the scattering rates between the electrons and optical phonons. Figure 4 shows the (a) interface and (b) confined mode phonon scattering rates as a function of electron energy Ek. For both (a) interface and (b) confined modes, the black solid line shows the total scattering rate which combines all contributions from each process indicated as dashed and dotted color lines. The general behavior of the scattering rate curves for both modes are similar. The LO emission scattering rates [(a) red and (b) orange dashed lines] start to dominate once the electron energy exceeds the threshold energy. The TO absorption processes are negligible compared to the others (not plotted in the figures). Due to mode mixing in wurtzites, the TO emission scattering rate is comparable to the LO absorption scattering rate. This causes the total scattering rate to show a two-step-like shape. The total scattering rate of both modes show roughly similar values that converge to ~1013 s−1 with Ek = 0.3 eV in the current system where the GaN thickness is set to d = 5 nm. As shown in Fig. 3, since we know that the interface mode phonons typically show larger group velocity, a comparable scattering rate between the interface and confined mode phonons indicates that the average phonon velocity of the phonons emitted due to these processes may be large enough to help dissipate the heat.
Focusing on the interface mode LO emission scattering rate [red dashed curve in (a)], we observe that the emission threshold energy is 103.2 meV. This energy corresponds to the energy of the LO resonant phonon frequency (ωLO,res = 832.3 cm−1) shown as the horizontal dotted line in Fig. 2(b). The LO phonon emission process through electron–phonon scattering can only occur when the electron has, at least, more energy than the phonon to be emitted; of course, more specifically, the condition described by Eq. (12) must be satisfied. The emission threshold energy of 103.2 meV indicates that phonons with at least this amount of energy are most likely to be emitted. From Fig. 3, we see that the group velocity of phonons with the resonant frequencies ωLO,res and ωTO,res are zero. The TO emission threshold energy (71.7 meV) also corresponds to the energy of TO resonant phonon frequency (ωTO,res = 577.8 cm−1). These observations of Fig. 4 suggest that, however large the group velocity of interface phonons could be, simply increasing the interface phonon mode scattering rate with respect to the confined phonon mode scattering rate may not improve the heat dissipation efficiency of the system.
For the confined modes in Fig. 4(b), the TO and LO emission threshold energies are shown as 67.6 and 91.6 meV, respectively. The TO emission threshold is slightly larger than ħω1z = 65.8 meV. As shown in the dispersion curve in Fig. 2(a), the confined mode phonon frequencies asymptotically approach ω1z with increasing phonon wave vector q. As the electron energy Ek increases, the energy and momentum conservation condition Eq. (12) [or Eq. (10) >0] is first satisfied at a considerably large q. It is revealed from the scattering rate calculation that this q is obtained when the phonon frequency ω is close to ω1z = 531 cm−1, but slightly larger. Similarly, the LO emission threshold is slightly smaller than ħω1Lt = 91.9 meV and this is due to the dispersion, shown in Fig. 2(b), approaching ω1Lt with increasing q. Since Fig. 2 is shown with the dimensionless x-axis wave vector qd, it is apparent that the emission threshold energies will also be affected by the GaN thickness d.
Figure 5 shows the interface and confined mode phonon emission scattering rates of an AlN/GaN/AlN double heterostructure with GaN thickness of d = 1 nm. Compared to the previous d = 5 nm case shown in Fig. 4, indeed, the interface mode scattering rate (red solid line) becomes approximately 8 times larger than the confined mode scattering rate (blue dashed line) for electron energy larger than 0.12 eV. Also notice that the interface mode scattering curve shows more than two of the step-like features. This is due to the emission threshold energy split between the symmetric and asymmetric interface modes. With d = 5, the wave vector q is only large enough to satisfy the emission condition at phonon frequencies of ω = ωTO(LO),res. However, with smaller d, this is no longer the case and the condition is satisfied with phonon frequencies slightly away from the resonant frequencies. As the symmetric and asymmetric interface modes are defined in separate phonon frequencies, except at the limit of ω → ωTO(LO),res, the threshold energies are split and causes the scattering rate curve to show more step-like increases.
To further examine the interface phonons that are emitted in the LO emission scattering process, the integrand of Eq. (9) as a function of phonon frequency for different electron energies Ek = 0.12, 0.3, and 0.5 eV is presented in Fig. 6. The plotted curves represent the number of phonons produced with each phonon frequency. The x-axis in this figure is shown in the units of cm−1, but should be interpreted as s−1 such that the integral of the curves over the phonon frequency results in the scattering rates represented in s−1.
The vertical dotted line in Fig. 6 indicates the LO resonant frequency ωLO,res = 832.3 cm−1. Phonons with frequency larger (smaller) than this resonant frequency are symmetric (asymmetric) modes. First, at Ek = 0.12 eV, which is slightly above the LO phonon emission threshold energy ELO,res = 103.2 meV, the phonons that are emitted show a small span of frequencies with the ones very close to ωLO,res = 832.3 cm−1 being the majority. As the electron energy increases, the scattering process starts to produce more phonons with frequencies farther away from the resonant frequency. With Ek = 0.5 eV, a large amount of phonons with ωLO,res ~ 832.3 cm−1 are still generated but the majority of the phonons possess frequencies that are approximately 30 cm−1 away from the resonant frequency. Returning to Fig. 3, we see that the group velocity of these LO interface phonon modes is around 30 km/s which is considerably large compared to the maximum group velocity of confined phonons (7 km/s) but still quite small compared to the maximum group velocity of the available interface phonons (138 km/s). In order to utilize the interface phonons with larger group velocity, the electron energy must be increased. However, with GaN thickness set to d = 5 nm, to utilize the entire span of available interface phonons and generate phonons with the maximum group velocity, calculation results show that the electron energy has to increase up to physically unrealistic values as high as Ek = 100 eV. An alternative way to produce interface mode phonons with high group velocity may be increasing the GaN thickness d as was suggested from the dispersion relation shown in Fig. 2. The group velocity (in Fig. 3) scales linearly with d; for example, if the thickness increases two-fold to d = 10 nm, the group velocity at each phonon frequency also increases to twice of the value calculated at d = 5 nm.
The relation between the GaN thickness d, phonon dispersion relation, interface phonon mode group velocity, and electron energy Ek must all be taken into account to understand if the nonzero interface mode phonons can be exploited to effectively dissipate heat of the system. To this end, we calculate and present in Fig. 7 the average group velocity of the emitted interface and confined mode phonons with different GaN thicknesses d = 1, 2, 5 and 10 nm as a function of electron energy Ek. Although a GaN thickness of 10 nm may be difficult to grow with the existing technology due to the strain associated with the lattice mismatch in AlN/GaN/AlN structures, we include it in our analysis to show the trend23. The procedure of obtaining the average group velocity is as follows: First, to the integrand of Eq. (9) (shown in Fig. 6), we multiply the phonon frequency dependent group velocity and evaluate the integral to obtain the sum of group velocities of all emitted phonons. After adding up all contributions from each interface and confined, TO and LO, symmetric and asymmetric phonon modes, we divide it with the total scattering rate to obtain the average group velocity. The average group velocity vg,avg may be expressed as:
where τe is the emission scattering rate obtained from Eq. (9), and vg is the group velocity of the corresponding phonon mode. As a reference, the longitudinal acoustic (LA) mode phonon’s sound velocity in GaN along the optical c-axis [0001] is shown as the horizontal dashed line24. Among all GaN thicknesses considered, we see a general trend of increasing average group velocity of emitted phonons as the electron energy increases. This is due to the increase of number of interface phonons with higher group velocities (i.e., phonons with frequency away from resonant frequencies) that are involved in the electron–phonon scattering process. Although in Fig. 6, we only show the case for d = 5 nm, similar trend was observed for all GaN thicknesses: with higher electron energy, more phonons with higher group velocity are emitted.
For the d = 5 nm case, at energies smaller than 103.2 meV, a step-like change in average group velocity is shown. This is due to the contribution of different phonon modes with different group velocities. As the electron energy increases, at each emission threshold energy ETO = 67.6 meV, ETO,res = 71.7 meV, ELO = 91.6 meV, and ELO,res = 103.2 meV (see Fig. 4), different modes of phonons start to emit, and their contributions appear in the curve as step-like shapes. At energies larger than ELO,res, most of the phonons that are emitted are confined and interface LO phonons, and the average group velocity is determined by the competition between these two factors. The step-like changes for the curves of different GaN thicknesses are omitted in the figure. For the d = 1 nm case, at low electron energies right above ELO,res = 103.2 meV, the average group velocity is the largest compared to the velocities with different thicknesses but has already almost saturated to its largest value which is around 6 nm/ps. As the thickness increases, the group velocity starts at a smaller value but increases more steadily and saturates at a larger value (the increase rate of velocity for the d = 10 nm case does not even start to saturate at Ek = 1.0 eV suggesting that it has potential to reach a higher value). From the curves, therefore, depending on the range of available electron energies and their distribution in energy, an appropriate GaN thickness can be selected such that the interface phonons can contribute to the heat dissipation process. Putting the electron energies and distribution aside, we see that the average group velocity can easily be engineered to a value comparable to the acoustic phonon’s sound velocity. Considering that the acoustic phonons are the major contributor of thermal conduction in semiconductor materials, the results suggest that the generated optical phonons of these systems may also contribute largely to the thermal conduction.
Conclusion
In conclusion, we have theoretically studied the interface and confined mode optical phonons of a wurtzite AlN/GaN/AlN double heterostructure and their interaction with electrons based on the uniaxial dielectric continuum model. The phonon dispersion relation of these phonon modes and the electron–phonon scattering rates are calculated numerically to derive the average group velocity of the emitted phonons to explore the possibility of exploiting the interface mode phonons as an additional heat dissipation channel. Our estimations show that the average group velocity of phonons that are emitted through electron–phonon scattering processes with electron energy slightly larger than the threshold energy (Ek ≈ ELO,res) is very small (for the d = 5 nm case, 0.9 nm/ps) compared to the LA phonon propagation velocity of bulk GaN (vsound = 8 nm/ps). This is due to the dispersion relation of interface mode phonons which shows curves that converge to the resonant phonon frequency at large phonon wave vector q. With larger electron energies, the average optical group velocity can exceed the acoustic phonon velocity starting from Ek = 0.35 eV. Given the energy distribution of electrons, we report that the quantum well thickness can be engineered to exploit the interface mode phonons, which can propagate a distance of few tens of nanometers before decaying into heat-carrying acoustic phonons.
References
Schmidt, M. C. et al. Demonstration of Nonpolar m -Plane InGaN/GaN Laser Diodes. Jpn. J. Appl. Phys. 46, L190–L191 (2007).
Mishra, U. K., Parikh, P. & Wu, Y. F. AlGaN/GaN HEMTs - An overview of device operation and applications. Proc. IEEE 90, 1022–1031 (2002).
Mishra, U. K., Likun, S., Kazior, T. E. & Wu, Y.-F. GaN-Based RF Power Devices and Amplifiers. Proc. IEEE 96, 287–305 (2008).
Ferry, D. K. Semiconductors. (Macmillian, 1991).
Lindsay, L., Broido, D. A. & Reinecke, T. L. Thermal Conductivity and Large Isotope Effect in GaN from First Principles. Phys. Rev. Lett. 109, 095901 (2012).
Balandin, A. A., Pokatilov, E. P. & Nika, D. L. Phonon Engineering in Hetero- and Nanostructures. J. Nanoelectron. Optoelectron. 2, 140–170 (2007).
Park, K., Stroscio, M. A. & Bayram, C. Investigation of electron mobility and saturation velocity limits in gallium nitride using uniaxial dielectric continuum model. J. Appl. Phys. 121, 245109 (2017).
Ridley, B. K. The LO phonon lifetime in GaN. J. Phys. Condens. Matter 8, L511–L513 (1996).
Barman, S. & Srivastava, G. P. Long-wavelength nonequilibrium optical phonon dynamics in cubic and hexagonal semiconductors. Phys. Rev. B 69, 235208 (2004).
Khurgin, J., Ding, Y. J. & Jena, D. Hot phonon effect on electron velocity saturation in GaN: A second look. Appl. Phys. Lett. 91, 1–4 (2007).
Matulionis, A. et al. Novel fluctuation-based approach to optimization of frequency performance and degradation of nitride heterostructure field effect transistors. Phys. Status Solidi Appl. Mater. Sci. 208, 30–36 (2011).
Sarkar, K. et al. Raman analysis of phonon modes in a short period AlN/GaN superlattice. Superlattices Microstruct. 115, 116–122 (2018).
Gleize, J. et al. Angular dispersion of polar phonons in a hexagonal GaN-AlN superlattice. Mater. Sci. Eng. B Solid-State Mater. Adv. Technol. 82, 27–29 (2001).
Lee, B. C., Kim, K. W., Stroscio, M. A. & Dutta, M. Optical-phonon confinement and scattering in wurtzite heterostructures. Phys. Rev. B 58, 4860 (1998).
Komirenko, S. M., Kim, K. W., Stroscio, M. A. & Dutta, M. Energy-dependent electron scattering via interaction with optical phonons in wurtzite crystals and quantum wells. Phys. Rev. B 61, 2034–2040 (2000).
Stroscio, M. A. & Dutta, M. Phonons in Nanostructures. Phonons in Nanostructures, https://doi.org/10.1017/CBO9780511534898 (Cambridge University Press, 2001).
Davydov, V. Y. et al. Phonon dispersion and Raman scattering in hexagonal GaN and AlN. Phys. Rev. B 58, 12899–12907 (1998).
Harima, H. Properties of GaN and related compounds studied by means of Raman scattering. J. Phys. Condens. Matter 14, R967–R993 (2002).
Loudon, R. The Raman effect in crystals. Adv. Phys. 13, 423–482 (1964).
Komirenko, S. M., Kim, K. W., Stroscio, M. A. & Dutta, M. Dispersion of polar optical phonons in wurtzite quantum wells. Phys. Rev. B 59, 5013–5020 (1999).
Perlin, P. et al. Determination of the effective mass of GaN from infrared reflectivity and Hall effect. Appl. Phys. Lett. 68, 1114–1116 (1996).
Baur, J., Maier, K., Kunzer, M., Kaufmann, U. & Schneider, J. Determination of the GaN/AlN band offset via the (−/0) acceptor level of iron. Appl. Phys. Lett. 65, 2211–2213 (1994).
Sohi, P., Martin, D. & Grandjean, N. Critical thickness of GaN on AlN: impact of growth temperature and dislocation density. Semicond. Sci. Technol. 32, 075010 (2017).
Bougrov, V., Levinshtein, M., Rumyantsev, S. & Zubrilov, A. Properties of Advanced Semiconductor Materials: GaN, AlN, InN, BN, SiC, SiGe. (John Wiley & Sons, 2001).
Acknowledgements
Part of this work, partially supported by the Air Force Office of Scientific Research (AFOSR) through Young Investigator Program Grant FA9550-16-1-0224, was carried out in the Micro and Nanotechnology Laboratory, University of Illinois at Urbana-Champaign, IL, USA and part of this work, partially supported by Air Force Office of Scientific Research (AFOSR) Grant FA9550-16-1-0227, was carried out at the University of Illinois at Chicago, IL, USA.
Author information
Authors and Affiliations
Contributions
M.A.S. and C.B. conceived and designed the research and supervised the whole project. K.P. carried out the calculations, performed analysis, and wrote the manuscript. A.M. and M.D. derived and verified the formalism. All authors participated in discussions of the results and commented on the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Park, K., Mohamed, A., Dutta, M. et al. Electron Scattering via Interface Optical Phonons with High Group Velocity in Wurtzite GaN-based Quantum Well Heterostructure. Sci Rep 8, 15947 (2018). https://doi.org/10.1038/s41598-018-34441-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-34441-4
- Springer Nature Limited