Abstract
The fibre-optic microwave photonic link has become one of the basic building blocks for microwave photonics. Increasing the optical power at the receiver is the best way to improve all link performance metrics including gain, noise figure and dynamic range. Even though lasers can produce and photodetectors can receive optical powers on the order of a Watt or more, the power-handling capability of optical fibres is orders-of-magnitude lower. In this paper, we propose and demonstrate the use of few-mode fibres to bridge this power-handling gap, exploiting their unique features of small acousto-optic effective area, large effective areas of optical modes, as well as orthogonality and walk-off among spatial modes. Using specially designed few-mode fibres, we demonstrate order-of-magnitude improvements in link performances for single-channel and multiplexed transmission. This work represents the first step in few-mode microwave photonics. The spatial degrees of freedom can also offer other functionalities such as large, tunable delays based on modal dispersion and wavelength-independent lossless signal combining, which are indispensable in microwave photonics.
Similar content being viewed by others
Introduction
Optical fibre has long been recognized as a superior medium for transmission of radio-frequency (RF) and microwave signals due to its low loss, large bandwidth, light weight and immunity to electromagnetic interference1, 2, 3, 4. The ability to simultaneously achieve high gain, low noise figure and large spurious-free dynamic range (SFDR) determines the roles fibre-optic microwave photonic links can play in many microwave photonics applications. Much research effort has been devoted to achieving this goal, including high-power lasers5, 6, linear, efficient and low-loss modulators7, 8, 9, and photodetectors with high quantum efficiency and power-handling capability10, 11. These efforts have enabled high-performance fibre-optic microwave photonic links12, 13, 14. Yet, so far the composite performance of a fibre-optic microwave photonic link realized using a low-loss optical fibre cannot compete with that using a high-loss microwave cable and a high-performance electronic amplifier.
It is well recognized that increasing the optical power before photodetection is the most effective way to simultaneously achieve high gain, low noise figure and large dynamic range15, 16, 17, 18. A 1-dB increase in the received optical power leads to a 2-dB increase in the detected microwave power, a 2-dB increase in thermal noise-dominated signal-to-noise ratio (SNR), and a 4/3-dB increase in SFDR15, 16, 17, 18. For reference, to achieve lossless transmission (0 dB microwave power gain) over a 20 km intensity-modulation direct-detection (IM-DD) fibre-optic microwave photonic link, the required input optical power is 63 mW or 18 dBm using a Mach–Zehnder modulator with a half-wave voltage of 4 V and an ideal photodiode15. This power-handling ability is well within the capabilities of the state-of-the-art optoelectronic components. Single-mode semiconductor lasers can produce optical power well over 40 dBm (Ref. 6). A travelling-wave photodiode with a maximum input power of over 25 dBm has also been demonstrated11. In comparison, the power-handling capability of optical fibres is orders-of-magnitude lower because of two dominant nonlinear effects in optical fibres, namely, stimulated Brillouin scattering (SBS)19, 20 and Kerr nonlinearity21, 22, 23. SBS results in strong backscattering that limits optical power available at the receiver, and degrades the SNR by introducing relative intensity noise due to multi-path interference24, 25, 26. The SBS threshold for a 20-km-long single-mode fibre (SMF) is only ~10 dBm (Ref. 27). Kerr nonlinearity results in self-phase modulation (SPM)21, cross-phase modulation28 and four-wave mixing (FWM)22 that leads to intermodulation distortions for single-channel transmission and nonlinear crosstalk for wavelength-division multiplexed (WDM) transmission23. For a 20-km standard SMF, a 1.0 radian SPM is induced for an input power of only 50 mW. Applications that require fibre-optic microwave photonic links of such lengths can be classified into two categories18: microwave signal distribution (antenna remoting and phased array29) and microwave signal processing1. In antenna remoting for radio astronomy, the link lengths can be greater than 20 km (Ref. 30). Other applications that require simultaneous transmission of multiple microwave signals using WDM include phased-array antennas31, 32 and microwave photonic transversal filters33, 34. For phased-array antennas, for example, the required SMF length for a 1-ns relative delay between antenna elements carried on WDM channels with spacing of 100 GHz is about 37 km.
Therefore, the bottleneck in improving the performance of fibre-optic microwave photonic links is the optical fibre itself. Yet there has been no concerted effort in improving the power-handling capability of optical fibres for such applications thus far. Optically preamplified links can use lower input powers and thus alleviate fibre nonlinearity but suffer SNR penalties (see detailed comparison in section 1 of Supplementary Information). Electrically amplifying input microwave signals does improve link gain, but it significantly deteriorates the SFDR due to nonlinear distortion in modulators15. Therefore, it is imperative to break the nonlinearity bottleneck of SMFs. We propose the use of few-mode fibres (FMF) to alleviate this bottleneck for long-haul (on the order of several kilometers) microwave photonic links35, 36. We specifically designed and fabricated FMFs for single-channel and WDM transmission of microwave signals. First, using a 20-km FMF with a small acousto-optic effective area and a large effective area of a high-order optical mode to overcome single-channel nonlinear limitations37, we increased the SBS threshold by 8.7 dB and the SFDR by 9.6 dB for single-channel analogue transmission as compared to that of a SMF of the same effective length. Second, by introducing FMFs into fibre-optic microwave photonic links, spatial orthogonality and phase walk-off among spatial modes can be exploited to suppress inter-channel nonlinear effects for WDM analogue transmission38. Using another 20-km FMF, we achieved a 30-dB reduction in nonlinear crosstalk, equivalent to a 20-dB increase in SFDR using mode-diversity WDM transmission. These demonstrations, together with recent advances in few-mode devices, can potentially usher in a new field of research, namely, few-mode microwave photonics.
Materials and methods
Single-channel microwave signal transmission in FMFs
FMFs can increase the nonlinear tolerance and thus optical power delivered to the photodetector for single-channel analogue transmission. Figure 1 shows the experimental setup for single-channel microwave transmission. A light wave emitted by a laser diode was modulated by two tones (1.893 and 2 GHz) using a Mach–Zehnder modulator (MZM), facilitating the standard two-tone test15, 17, 39 for microwave photonic links that typically carry high carrier-to-noise ratio signals40, 41. The MZM was low biased to suppress the optical carrier42. The modulated light wave was amplified, filtered and launched into a 20-km long specially designed FMF fibre via an optical circulator, which was used to measure the back-scattered light. A mode-selective photonic lantern (MSPL)43 was inserted between the circulator and the FMF to convert the input LP01 fundamental mode into a specific spatial mode supported by the FMF. Figure 1b shows the structure of the MSPL that was fabricated by adiabatically tapering six input fibres of different sizes inserted into a Fluorine-doped capillary. The cross-sectional view of the MSPL output facet is shown in Figure 1c, and the output intensity profile corresponding to each input port at near field and far field are shown in Figure 1d. The mismatch between the MSPL output and the modes supported by the FMF leads to mode crosstalk. For single-channel applications, we need at least one stable mode with a large effective area in the FMF of length (crosstalk) orders-of-magnitude larger (smaller) than for those for high-power laser applications44. The refractive-index profile of the specially designed FMF for this application is shown in Figure 1e. With this structure, the LP02 mode is the most stable mode in the FMF (see section 2 of Supplementary Information for explanation). As can be seen in Figure 1f, the impulse response (see section 3 of Supplementary Information) of the LP02 mode is almost void of crosstalk from other modes. The low-crosstalk nature of the LP02 mode is also verified by the almost ideal intensity profile at the output of the FMF, as shown in the inset. The core radius of the FMF is about 11.5 μm yielding an effective area of 270 μm2, which is about 3.8 times (5.8 dB) larger than that of the SMF. The attenuation coefficient for the LP02 mode is 0.27 dB km−1 at 1550 nm. The received signal is detected by a free-space photodetector and evaluated by an electrical spectrum analyzer.
WDM microwave signal transmission FMFs
In WDM microwave transmission, the orthogonality and walk-off of different spatial modes in FMF can be utilized to suppress WDM crosstalk mediated by fibre nonlinearity, which entails a different fibre design compared to the single-channel case as shown below. Figure 2a shows the experimental setup. Two optical carriers with 100-GHz channel spacing were coupled into the FMF through the MSPL. Without loss of generality, we set the long-wavelength channel as the target channel, which was modulated by two tones and was always launched into the LP01 mode of the FMF. The co-polarized interfering channel at the shorter wavelength was modulated by a single tone and could be launched into any one of the 4 LP modes: LP01, LP11, LP21 and LP02. Since the microwave signal is carried on one mode only in our approach, the transfer function of the link is similar to that of SMF links, free of multi-modal dispersion45. The inset illustrates how FWM involving the optical carrier in the target channel and the optical carrier and one sideband of the interfering channel generates an in-band crosstalk for the target channel. Since this nonlinear crosstalk is in-band, it cannot be removed by filtering in the optical or electrical domains. To suppress such a nonlinear crosstalk, we propose and demonstrate transmitting the two WDM channels over two different modes, exploiting spatial orthogonality and increased phase mismatch among the interacting waves in addition to a larger effective area. It is possible to satisfy the phase-matching condition for FWM between different modes with frequency detuning on the order of several THz in FMFs46, 47. In that case, spatial orthogonality between modes will still limit the FWM efficiency. For this application, there needs to be at least two stable modes that can be transported in the FMF. This is accomplished by designing and fabricating a fibre with a large effective index difference between the fibre modes48, 49. Figure 2b and 2c shows the cross-sectional image and measured refractive-index profile respectively. The estimated core radius is 8 μm resulting an effective area of 120 μm2, about 1.6 times of that of the standard SMF. The attenuation coefficients range from the smallest at 0.227 dB km−1 for the LP01 mode to the largest at 0.262 dB km−1 for the LP02 mode at 1550 nm. Six mode patterns, with high purity after transmitting through the FMF, are displayed in Figure 2d. The impurities in the output mode pattern mainly come from discrete crosstalk of the MSPL. Distributed crosstalk in the FMF itself is rather low, as can be seen in the impulse response in Figure 2e. Discrete mode crosstalk of the MSPL is estimated to be less than −9 dB. As a linear crosstalk, discrete crosstalk can be filtered out in the optical domain as each mode is transmitted on a different wavelength. We employed two cascaded filters to suppress this linear interference before photodetection for the target signal carried on the LP01 mode. The input SMF of the filter was spliced directly to the FMF to receive the target signal. The residual optical power from the interfering channel was 34 dB down from the optical power in the target channel, leading to a background microwave signal crosstalk of less than −60 dB.
Results and discussion
Single-channel microwave signal transmission in FMFs
Figure 3 shows the performances of the FMF microwave photonic link, in comparison with a SMF microwave photonic link. For a fair comparison of nonlinear performances, the lengths of the FMF and SMF are set to 20 and 16.6 km, respectively, so that they have an identical effective nonlinear length. In Figure 3a, the back-scattered and transmitted optical powers are plotted against normalized optical launch power under microwave modulation. This normalization equalizes the loss of these two links (see section 4 of Supplementary Information for justifications and detailed procedures) so that the two links produce the same power at the fundamental frequency for the same normalized optical launch power without fibre nonlinearity. The SBS threshold for the FMF is ~25 dBm, about 8.7 dB larger than that of SMF. The resulting transmitted optical power at the SBS threshold is also 8.7 dB higher for the FMF. Even though the transmitted optical power increases beyond the SBS threshold, the transmitted signal contains multi-path interference due to SBS, leading to severe degradations in the SNR50, 51. So, the maximum useful transmitted optical power is at the SBS threshold. The reason why the transmitted power still increases beyond the SBS threshold is because the power in the optical carrier is transferred to the sidebands through the Kerr effect, including SPM and FWM. Although the power of the optical carrier stops increasing due to SBS, the power of sidebands will grow if they are below the SBS threshold. As a result, the total transmitted optical power continues to increase but at a slower rate than below the SBS threshold. This is different from the CW case50, 51, where the transmitted power stops increasing beyond SBS threshold. Based on the effective areas of these two fibres, the SBS threshold for the FMF should be only 5.8 dB higher. An important factor for the additional increase in the SBS threshold is that the guided acoustic waves52, 53 have a smaller overlap with the high-order modes than with the fundamental mode (see section 5 of Supplementary Information), an advantage that can only be materialized in FMF fibres. In other words, high-order modes have smaller acousto-optic effective areas54, 55 than the fundamental mode. Back reflection from the interface between the photonic lantern and the FMF may also lead to a slight overestimation of the SBS threshold.
The 8.7-dB increase in maximum transmitted optical power at the SBS threshold for the FMF leads to a 17.0-dB increase in detected microwave power or, equivalently, a 17.0-dB increase in the link gain as shown in Figure 3b. Even if we assume the launch power for the SMF could be increased to the SBS threshold for the FMF, the FMF link gain is still 6 dB higher than the SMF link. Increases in the gain can support longer transmission distances or larger splitting ratios.
The third-order intermodulation distortion (IMD3) also grows with the normalized optical launch power, as shown in Figure 3c. Different from the fundamental power, there is no deceleration of the IMD3 power beyond the SBS threshold. This is because the Kerr nonlinearity induces power transfer to IMD3. The optical spectral components that result in IMD3 include not only the optical carrier but also the modulation sidebands and FWM sidebands. As explained in section 6 of the Supplementary Information, the dominant contribution to the fundamental power comes from the optical carrier. As the optical carrier is depleted by the SBS, the fundamental power grows sub-linearly with the square of the launch power (slope of 1.3 on a log–log scale, smaller than the slope of 2 in the linear regime). In contrast, the dominant contribution to IMD3 comes from the modulation sidebands, which increase in power due to parametric amplification even beyond the SBS threshold. As a result, the IMD3 power still grows as a function of launch power at a slope of 2.5 on a log–log scale beyond the SBS threshold. It should be noted that, even though the effective area of the FMF is large and therefore the Kerr nonlinear coefficient is smaller, IMD3 in the FMF link is stronger at high launch powers, because the power in the optical carrier is stronger due to weaker SBS as compared to that in SMF.
As expected, the rate of increase in SFDR as a function of the normalized optical launch power, as shown in Figure 3d, will slow down once fibre nonlinearities set in. On one hand, the received microwave power at the fundamental frequencies will be suppressed due to SBS. Generally, a 1-dB reduction in fundamental power leads to 1-dB reduction in SFDR. On the other hand, FWM increases the IMD3. Generally, a 1-dB increase in IMD3 results in a 1/3-dB reduction in SFDR. Since the FMF has a higher SBS threshold than the SMF, the resulting SFDR of the FMF link is 4.8 dB higher than that of the SMF link at the SBS threshold of the FMF. The contributions of the microwave power at the fundamental frequency and IMD3 are 6 and −1.2 dB, respectively. However, analogue links should not operate above the SBS threshold as discussed before. So when compared at their respective SBS thresholds, the SFDR of the FMF link is 9.6 dB higher than that of the SMF link, where the contributions of the fundamental and IMD3 powers are 17.9 and −8.3 dB, respectively.
WDM microwave signal transmission in FMFs
Figure 4 compares the nonlinear crosstalk in WDM transmission with and without mode diversity versus received optical power. The difference for degenerated modes in the same mode group is small (see section 7 of Supplementary Information). As expected, a 1-dB increase in received optical power leads to a 3-dB rise in the nonlinear crosstalk, as shown in Figure 4a, in comparison with the 2-dB rise in IMD3. This is because the nonlinear crosstalk comes from the interaction of optical carrier of the target channel, and optical carrier and sidebands of the interfering channel, while IMD3 comes from the beating between the sidebands corresponding to the two tones, which is much weaker than the optical carrier. At moderate received optical powers, the nonlinear crosstalk easily surpasses the noise floor set by the photodetection process (−115 dB kHz−1 in our experiment). In this case, the noise floor that is normally used to define SFDR should be replaced by the nonlinear crosstalk (see section 8 of Supplementary Information). The reduction in SFDR due to nonlinear crosstalk can reach a few tens of dB as shown in Figure 4b. The values of 63.7, 56.9, 53.8 and 44.6 dB correspond SFDRs for each mode at the onset of FWM crosstalk (similarly defined to the SBS threshold). The most serious case is when both channels are in the LP01 mode. Using mode diversity, suppression of nonlinear crosstalk up to 30-dB, equivalent to a 20-dB increase in SFDR, was obtained. This level of nonlinear crosstalk suppression, although already very significant, was in fact much smaller than theoretically possible because the spatial orthogonality condition was not completely maintained due to linear crosstalk of the MSPL into the LP01 mode. As shown in Figure 3e, the LP21 mode has the least amount of mode crosstalk that results in the lowest nonlinear crosstalk.
Discussion
Further improvements in few-mode fibre-optic microwave photonic links rely on reducing the loss and crosstalk of the FMF link. Fortunately, it is expected that both the loss and crosstalk can be improved significantly from the links used in these experiments. In terms of losses, a few-mode fibre with loss as low as 0.16 dB km−1 has been demonstrated recently56. Fundamentally, the loss of FMFs should be comparable to that of traditional SMFs. Distributed mode crosstalk produced by the FMF itself can be reduced to negligible levels by increasing refractive-index difference and proper profile design49. Likewise, discrete mode crosstalk introduced by the mode multiplex can also be improved by optimizing the photonic lantern57 or employing other multiplexing techniques such as the directional coupler58 and the multi-plane light conversion59.
The optimum number of modes for the FMF is indeed a critical parameter for WDM applications. In theory, if modes are truly orthogonal and free from crosstalk among each other, then the more modes we have, the more WDM channels can be accommodated in FMF transmission to avoid crosstalk. But in practice, linear crosstalk and fibre loss increases with the number of modes in the FMF and the mode multiplexers and demultiplexers. The optimum number of modes depends on technological progress in controlling crosstalk and loss. The employment of FMF can also mitigate other nonlinear distortions, in particular, second-order IMD for the transmission of multi-octave microwave signals.
It is also important to know at what length scale microwave photonic links should use FMFs instead of SMFs, especially in view of the potentially higher losses for FMF links. First, contrary to intuition, excess losses due to mode exciting devices such as the photonic lantern do not affect the link performance. This is because these losses can be easily compensated by increasing the optical power of the transmitting laser. Second, at short lengths, the maximum output power of the link will be predominantly determined by the nonlinear tolerance (the effective area) and not the loss of the fibre. So, FMFs will offer larger gains and dynamic ranges than SMFs (although for some applications, SMFs may be adequate). Third, at long distances, both fibre attenuation and effective area will affect the link performance since they determine how much power can be injected into the link and how much power actually arrives at the receiver. At long distances, FMF links will outperform SMF links if
where the SBS threshold for the FMF or SMF, or , is a function of fibre attenuation coefficient α, effective area Aeff and fibre length L27. The left-hand and right-hand side of Equation (1) denotes the maximum output power without impairments from SBS for the FMF and SMF links, respectively. Using parameters of FMFs in this work, Equation (1) is satisfied for length up to 75 (45) km for the single-channel (WDM) transmission, respectively. Since the nonlinear length is shorter than 45 km, the best choice for long-distance links is to use FMFs at the beginning of the link where the optical power is the highest and then switch to low-loss SMFs past the nonlinear length of the FMF. Taking into account the three points above, we conclude that FMFs will lead to microwave photonic links with better performances regardless of the link length.
The spatial degrees of freedom have not been exploited for microwave photonics applications so far. We envision that few-mode microwave photonics can also offer other indispensable functionalities. For example, using few-mode components, we can generate large tunable delays based on modal dispersion45 and realize wavelength-independent lossless signal combining as the performance of the MSPL can be made wavelength independent60. This work, therefore, represents the first step in the new field of few-mode microwave photonics.
Conclusions
In this paper, we demonstrate order-of-magnitude improvement in dynamic range for both single-channel and WDM transmission of microwave signals. Without the single-mode constraint, FMFs can provide much larger effective areas than commercial single-mode, large effective-area fibres. Few-mode fibres also afford the opportunity to reduce the overlap between the guided acoustic and optical modes. Both of these factors increase the SBS threshold of FMFs. Significant increase in the SBS threshold and the nonlinear coefficient allow much larger optical powers to be launched and transported in the FMF. This work represents the first demonstration of using FMF to address the power-handling limitations of optical fibres for fibre-optic microwave photonic links. Furthermore, the introduction of the spatial degree of freedom into microwave signal transmission opens opportunities that cannot be afforded in single-mode fibres. Here we demonstrated suppression of nonlinear crosstalk by exploiting the orthogonality and walk-off of spatial modes.
References
Capmany J, Novak D . Microwave photonics combines two worlds. Nat Photonics 2007; 1: 319–330.
Cox CH, Ackerman EI, Betts GE, Prince JL . Limits on the performance of RF-over-fiber links and their impact on device design. IEEE Trans Microwave Theory Tech 2006; 54: 906–920.
Seeds AJ, Williams KJ . Microwave photonics. J Lightw Technol 2006; 24: 4628–4641.
Yao JP . Microwave photonics. J Lightw Technol 2009; 27: 314–335.
Ackerman EI, Betts GE, Burns WK, Campbell JC, Cox CH et al. Signal-to-noise Performance of Two Analog Photonic Links Using Different Noise Reduction Techniques. 2007 IEEE/MTT-S International Microwave Symposium; 3–8 June 2007; Honolulu, HI, USA, pp. 51–54. IEEE: Honolulu, HI, USA, 2007.
Fiebig C, Blume G, Kaspari C, Feise D, Fricke J et al. 12 W high-brightness single-frequency DBR tapered diode laser. Electron Lett 2008; 44: 1253–1255.
Ackerman EI . Broad-band linearization of a Mach-Zehnder electrooptic modulator. IEEE Trans Microw Theory Tech 1999; 47: 2271–2279.
Howerton MM, Moeller RP, Greenblatt AS, Krahenbuhl R . Fully packaged, broad-band LiNbO3 modulator with low drive voltage. IEEE Photonics Technol Lett 2000; 12: 792–794.
Li GL, Yu PKL . Optical intensity modulators for digital and analog applications. J Lightw Technol 2003; 21: 2010–2030.
Ishibashi T, Kodama S, Shimizu N, Furuta T . High-speed response of uni-traveling-carrier photodiodes. Jpn J Appl Phys 1997; 36: 6263–6268.
Xie XJ, Zhou QG, Li KJ, Shen Y, Li QL et al. Improved power conversion efficiency in high-performance photodiodes by flip-chip bonding on diamond. Optica 2014; 1: 429–435.
Urick VJ, Rogge MS, Bucholtz F, Williams KJ . Wideband (0.045–6.25 GHz) 40 km analogue fibre-optic link with ultra-high (>40 dB) all-photonic gain. Electron Lett 2006; 42: 552–553.
Chen ZY, Yan LS, Pan W, Luo B, Zou XH et al. SFDR enhancement in analog photonic links by simultaneous compensation for dispersion and nonlinearity. Opt Express 2013; 21: 20999–21009.
McKinney JD, Godinez M, Urick VJ, Thaniyavarn S, Charczenko W et al. Sub-10-dB noise figure in a multiple-GHz analog optical link. IEEE Photonics Technol Lett 2007; 19: 465–467.
Cox CH III . Analog Optical Links: Theory and Practice. Cambridge: Cambridge University Press; 2004.
Rumelhard C, Algani C, Billabert AL . Microwaves Photonic Links: Components and Circuits. Hoboken, NJ: John Wiley & Sons; 2013.
Urick VJ, Williams KJ, McKinney JD . Fundamentals of Microwave Photonics. Chichester: John Wiley & Sons; 2015.
Urick VJ, Bucholtz F, McKinney J, Devgan PS, Campillo AL et al. Long-haul analog photonics. J Lightw Technol 2011; 29: 1182–1205.
Ippen EP, Stolen RH . Stimulated Brillouin scattering in optical fibers. Appl Phys Lett 1972; 21: 539–541.
Smith RG . Optical power handling capacity of low loss optical fibers as determined by stimulated Raman and Brillouin scattering. Appl Opt 1972; 11: 2489–2494.
Stolen RH, Lin C . Self-phase-modulation in silica optical fibers. Phys Rev A 1978; 17: 1448–1453.
Hill KO, Johnson DC, Kawasaki BS, MacDonald RI . cw three-wave mixing in single-mode optical fibers. J Appl Phys 1978; 49: 5098–5106.
Chraplyvy AR . Limitations on lightwave communications imposed by optical-fiber nonlinearities. J Lightw Technol 1990; 8: 1548–1557.
Horowitz M, Chraplyvy AR, Tkach RW, Zyskind JL . Broad-band transmitted intensity noise induced by Stokes and anti-Stokes Brillouin scattering in single-mode fibers. IEEE Photonics Technol Lett 1997; 9: 124–126.
David A, Horowitz M . Low-frequency transmitted intensity noise induced by stimulated Brillouin scattering in optical fibers. Opt Express 2011; 19: 11792–11803.
Le Bras H, Moignard M, Charbonnier B . Brillouin Scattering in Radio Over Fiber Transmission. Optical Fiber Communication Conference and Exposition and The National Fiber Optic Engineers Conference, pp. JWA86. Optical Society of America: Anaheim, CA, 2007.
Kobyakov A, Sauer M, Chowdhury D . Stimulated Brillouin scattering in optical fibers. Adv Opt Photonics 2010; 2: 1–59.
Islam MN, Simpson JR, Shang HT, Mollenauer LF, Stolen RH . Cross-phase modulation in optical fibers. Opt Lett 1987; 12: 625–627.
Payne J, Shillue B, Vaccari A . Photonic Techniques for Use on the Atacama Large Millimeter Array. International Topical Meeting on Microwave Photonics. Melbourne, Victoria: IEEE; 1999, pp. 105–108.
Wootten A, Thompson AR . The Atacama large millimeter/submillimeter array. Proc IEEE 2009; 97: 1463–1471.
Ng W, Walston AA, Tangonan GL, Lee JJ, Newberg IL et al. The first demonstration of an optically steered microwave phased array antenna using true-time-delay. J Lightw Technol 1991; 9: 1124–1131.
Goutzoulis AP, Zomp JM . Development and field demonstration of an eight-element receive wavelength-multiplexed true-time-delay steering system. Appl Opt 1997; 36: 7315–7326.
Capmany J, Ortega B, Pastor D . A tutorial on microwave photonic filters. J Lightw Technol 2006; 24: 201–229.
Liao JX, Xue XX, Wen H, Li SY, Zheng XP et al. A spurious frequencies suppression method for optical frequency comb based microwave photonic filter. Laser Photonics Rev 2013; 7: L34–L38.
Urick VJ, Knapp PF, Swingen L, Rogge MS, Campillo AL et al. Design and Characterization of Long-Haul Single-Channel Intensity-Modulated Analog Fiber-Optic Links. Washington, DC: Naval Research Lab; 2005.
Urick VJ, Hastings A, Dexter JL, Williams KJ, Sunderman C et al. Field Test on the Feasibility of Remoting HF Antenna with Fiber Optics. Washington, DC: Naval Research Lab; 2008.
Wen H, Zheng HJ, Mo Q, Velázquez-Benitez AM, Xia C et al. Analog Fiber-Optic Links Using High-Order Fiber Modes. 2015 European Conference on Optical Communication (ECOC); 27 September–1 October 2015; Valencia, pp. 1-3. IEEE: Valencia, 2015.
Wen H, Mo Q, Sillard P, Amezcua Correa R, Li GF . Analog Transmission Over Few-Mode Fibers. Optical Fiber Communication Conference, pp. Th4A.3. Optical Society of America: Anaheim, CA, USA, 2016.
Urick VJ . Long-Haul Analog Links Tutorial. 2010 Conference on Optical Fiber Communication (OFC), Collocated National Fiber Optic Engineers Conference; 21–25 March 2010; San Diego, CA, USA. IEEE: San Diego, CA, USA, 2010.
Montebugnoli S, Boschi M, Perini F, Faccin P, Brunori G et al. Large antenna array remoting using radio-over-fiber techniques for radio astronomical application. Microw Opt Technol Lett 2005; 46: 48–54.
Sauer M, Kobyakov A, George J . Radio over fiber for picocellular network architectures. J Lightw Technol 2007; 25: 3301–3320.
Farwell ML, Chang WSC, Huber DR . Increased linear dynamic range by low biasing the Mach-Zehnder modulator. IEEE Photonics Technol Lett 1993; 5: 779–782.
Leon-Saval SG, Fontaine NK, Salazar-Gil JR, Ercan B, Ryf R et al. Mode-selective photonic lanterns for space-division multiplexing. Opt Express 2014; 22: 1036–1044.
Ramachandran S, Nicholson JW, Ghalmi S, Yan MF, Wisk P et al. Light propagation with ultralarge modal areas in optical fibers. Opt Lett 2006; 31: 1797–1799.
Gasulla I, Capmany J . Microwave photonics applications of multicore fibers. IEEE Photonics J 2012; 4: 877–888.
Essiambre RJ, Mestre MA, Ryf R, Gnauck AH, Tkach RW et al. Experimental investigation of inter-modal four-wave mixing in few-mode fibers. IEEE Photonics Technol Lett 2013; 25: 539–542.
Xiao YZ, Essiambre RJ, Desgroseilliers M, Tulino AM, Ryf R et al. Theory of intermodal four-wave mixing with random linear mode coupling in few-mode fibers. Opt Express 2014; 22: 32039–32059.
Sillard P, Astruc M, Boivin D, Maerten H, Provost L . Few-Mode Fiber for Uncoupled Mode-Division Multiplexing Transmissions. 37th European Conference and Exposition on Optical Communications; 18–22 September 2011; Geneva, pp. Tu.5.LeCervin.7. Optical Society of America: Geneva, 2011.
Maruyama R, Kuwaki N, Matsuo S, Ohashi M . Experimental Investigation of Relation Between Mode-Coupling and Fiber Characteristics in Few-Mode Fibers. Optical Fiber Communication Conference, pp. M2C.1. Optical Society of America: Los Angeles, CA, USA, 2015.
Fishman DA, Nagel JA . Degradations due to stimulated Brillouin scattering in multigigabit intensity-modulated fiber-optic systems. J Lightw Technol 1993; 11: 1721–1728.
Ruffin AB . Stimulated Brillouin Scattering: an Overview of Measurements, System Impairments, and Applications. Technical Digest: Symposium on Optical Fiber Measurements; 28–30 September 2004; Boulder, CO, USA, pp. 23-28. IEEE: Boulder, CO, USA, 2004.
Shelby RM, Levenson MD, Bayer PW . Guided acoustic-wave Brillouin scattering. Phys Rev B 1985; 31: 5244–5252.
Waldron RA . Some problems in the theory of guided microsonic waves. IEEE Trans Microw Theory Tech 1969; 17: 893–904.
Ruffin AB, Li MJ, Chen X, Kobyakov A, Annunziata F . Brillouin gain analysis for fibers with different refractive indices. Opt Lett 2005; 30: 3123–3125.
Kobyakov A, Kumar S, Chowdhury DQ, Ruffin AB, Sauer M et al. Design concept for optical fibers with enhanced SBS threshold. Opt Express 2005; 13: 5338–5346.
Hayashi T, Tamura Y, Hasegawa T, Taru T . 125-μm-Cladding Coupled Multi-Core Fiber with Ultra-Low Loss of 0.158 dB/km and Record-Low Spatial Mode Dispersion of 6.1 ps/km1/2. Optical Fiber Communication Conference Postdeadline Papers, pp.Th5A.1. Optical Society of America: Anaheim, CA, 2016.
Huang B, Fontaine NK, Ryf R, Guan BB, Leon-Saval SG et al. All-fiber mode-group-selective photonic lantern using graded-index multimode fibers. Opt Express 2015; 23: 224–234.
Huang B, Xia C, Matz G, Bai N, Li GF . Structured Directional Coupler Pair for Multiplexing of Degenerate Modes. Optical Fiber Communication Conference/National Fiber Optic Engineers Conference 2013, pp. JW2A.25. Optical Society of America: Anaheim, CA, 2013.
Labroille G, Denolle B, Jian P, Genevaux P, Treps N et al. Efficient and mode selective spatial mode multiplexer based on multi-plane light conversion. Opt Express 2014; 22: 15599–15607.
Xia C, Chand N, Velázquez-Benitez AM, Liu X, Lopez JEA et al. Demonstration of World’s First Few-Mode GPON. 2014 The European Conference on Optical Communication (ECOC); 21–25 September 2014; Cannes, pp. 1-3. IEEE: Cannes, 2014.
Acknowledgements
This work is supported in part by the National Basic Research Program of China (973) Project #2014CB340104/3, NSFC Projects 61335005, 61377076, 61575142, 61431009 and 61671227, the United States Army Research Office grant W911NF-13-1-0283 and Shandong Provincial Natural Science Foundation (ZR2011FM015).
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
Competing interests
The authors declare no conflict of interest.
Additional information
Note: Supplementary Information for this article can be found on the Light: Science & Applications’ website.
Supplementary information
Rights and permissions
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc-sa/4.0/
About this article
Cite this article
Wen, H., Zheng, H., Mo, Q. et al. Few-mode fibre-optic microwave photonic links. Light Sci Appl 6, e17021 (2017). https://doi.org/10.1038/lsa.2017.21
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1038/lsa.2017.21
- Springer Nature Limited
Keywords
This article is cited by
-
Integrated lithium niobate microwave photonic processing engine
Nature (2024)
-
Low-loss microwave photonics links using hollow core fibres
Light: Science & Applications (2022)
-
Fast mode decomposition in few-mode fibers
Nature Communications (2020)