Abstract
Based on the computational fluid dynamics (CFD) and the experiment technology, this paper presents a new type of the twin-screw pump for the water-supply and studies its hydraulic performance with the hydraulic performance test. The internal flow characteristics and the hydraulic performance of the twin-screw pump are numerically simulated. The CFD results show that at different heads, the screw pressure gradually increases from the inlet end face along the axial direction of the screw to the outlet end face. The pressure distribution in the screw groove is relatively uniform, the screw clearance and the meshing area pressure are different from the screw groove pressure distribution. Under the same working condition of the head, the pressure distributions in the screw below and above the design speed are the same as the pressure distribution at the design speed, and with the range of the pressure value quite close. As the rotating speed increases furthermore, the flow rate and the volume efficiency of the pump both increase. At different rotating speeds, the velocity distributions along the axial direction of the screw are similar. A test rig is built, which consists of a closed-loop circuit, and the test results are found in good agreement with the CFD predictions. The experimental results show that the flow rate-head curves of the twin-screw pumps are similar at different rotating speeds. The research shows that the designed twin-screw pump enjoys a higher volumetric efficiency and a lower shaft power when the axial clearance is 0.08 mm-0.12 mm. When the clearance is 0.1 mm, the volumetric efficiency is the highest.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Li F. Screw pump [M]. Beijing, China: Machine Press, 2010(in Chinese).
Yan D., Tang Q., Kovacevic A. et al. Rotor profile design and numerical analysis of 2–3 type multiphase twin-screw pumps [J]. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2018, 232(2): 186–202.
Liu P., Morrison G., Patil A. Experimental and analytical investigation of a novel multistage twin-screw pump [J]. Journal of Energy Resources Technology, 2019, 141(12): 122101.
An Y., Song Y., Zhang D. et al. Three dimensional motion simulation and locus optimization design of progressive cavity pump rotor [J]. Journal of China University of Petroleum (Edition of Natural Science), 2012, 36(3): 155–158, 164(in Chinese).
Wang J., Wei S., Sha R. et al. Design methodology of a new smooth rotor profile of the screw vacuum pump [J]. Vacuum, 2019, 159: 456–463.
Li Z., Zhang R., Gao Y. et al. Profile analysis and simulation of twin-screw pump [J]. China Petroleum Machinery, 2008, 36(3): 41–44(in Chinese).
Chen J., Wang L., Chen D. Revise of double-screw pump profile [J]. Fluid Machinery, 2006, 34(6): 41–43.
Tang Q., Zhang Y. Screw optimization for performance enhancement of a twin-screw pump [J]. Proceedings of the Institution of Mechanical Engineers, 2014, 228(1): 73–84.
Yan D., Kovacevic A., Tang Q. Numerical modelling of twin-screw pumps based on computational fluid dynamics [J]. Proceedings of the Institution of Mechanical Engineers, 2017, 231(24): 4617–4634.
Ohbayashi T., Sawada T., Hamaguchi M. Study on the performance prediction of screw vacuum pump [J]. Applied Surface Science, 2001, 169: 768–771.
Zhang H. Y., Zhang W. Y., Zhu D. P. Study on design of twin- screw pump with high pressure water [J]. Ship Engineering, 2015, S1: 117–118(in Chinese).
Hu B., Cao F., Yang X. Theoretical and experimental study on conveying behavior of a twin-screw multiphase pump [J]. Proceedings of the Institution of Mechanical Engineers, 2016, 230(4): 304–315.
Liu P., Patil A., Morrison G. Multiphase flow performance prediction model for twin-screw pump [J]. Journal of Fluids Engineering, 2018, 140(3): 031103.
Zhang Y., Tang Q., Li Z. et al. Leakage mechanism of screw pump based on leakage model in fluid mechanics [J]. Transactions of the Chinese Society for Agricultural Machinery, 2014, 45(10): 326–332, 339(in Chinese).
Zhang Y. Investigation on the design and manufacuture processing technology of sealed twin-screw rotor [D]. Master Thesis, Chongqing, China: Chongqing University, 2010(in Chinese).
Zhang Y. Characteristic analysis of volumetric efficiency and precision forming research of rotors for screw pump [D]. Doctoral Thesis, Chongqing, China: Chongqing University, 2014(in Chinese).
Patil A. Performance evaluation and CFD simulation of multiphase twin-screw pumps [D]. Doctoral Thesis, College Station, TX, USA: Texas A&M University, 2013.
Yin X., Cao F., Pan S. Numerical investigation on screw rotor deformation and influence on volumetric efficiency of the twin-screw multiphase pump [J]. Applied Thermal Engineering, 2017, 111(25): 1111–1118.
Wang X. Design theory and simulation study of water hydraulic twin-screw pump with medium and high pressure [D]. Master Thesis, Chongqing, China: Chongqing University, 2014(in Chinese).
Chu T., Wang C., Wang X. et al. Numerical simulation study of screw pump internal flow field [J]. Fluid Machinery, 2014, 42(5): 21–24.
Wang C., Chen X., Qiu N. et al. Numerical and experimental study on the pressure fluctuation, vibration, and noise of multistage pump with radial diffuser [J]. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2018, 40(10): 481.
Wang C., Shi W., Wang X. et al. Optimal design of multistage centrifugal pump based on the combined energy loss model and computational fluid dynamics [J]. Applied Energy, 2017, 187: 10–26.
Acknowledgments
This work was supported by the Innovation Capability Planning Project-Colleges and Universities Cooperation Project (Grant No. YZ2017289), the Postgraduate Research and Practice Innovation Program of Jiangsu Province (Grant No. XKYCX19_089), the Six talent peaks project in Jiangsu Province (Grant No. 2015-JXQC-007), the Water conservancy science and technology project of Jiangsu Province (Grant No. 2019014), the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD) and the Jiangsu Province 333 high level talents training project and Jiangsu Planned Projects for Postdoctoral Research Funds (Grant No. 1701189B).
Author information
Authors and Affiliations
Corresponding author
Additional information
Project supported by the National Natural Science Foundation of China (Grant No. 51779214).
Biography: Di Zhang (1994-), Male, Ph. D. Candidate
Rights and permissions
About this article
Cite this article
Zhang, D., Cheng, L., Li, Yy. et al. The hydraulic performance of twin-screw pump. J Hydrodyn 32, 605–615 (2020). https://doi.org/10.1007/s42241-020-0938-9
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s42241-020-0938-9