Abstract
The normal T6 heat treatment process for cast A356 alloy generally requires about 15 h. This long-period procedure increases greatly the manufacturing cost and decreases the productivity in practical production. In this study, a new short-time heat treatment process with only 30 min solution time at 540 °C was developed for the production of motorcycle wheel hubs in order to reduce heat treatment time. Comparisons on microstructure evaluation and mechanical properties, such as tensile strength and ductility, were made between this new fast process and the conventional T6 heat treatment. The results revealed that this new heat treatment process enabled the spheroidization of the eutectic silicon thoroughly, while minimizing the growth of eutectic silicon. The A356 alloy after this new short-time heat treatment shows nearly equal mechanical properties compared with the same alloy heat treated in a normal T6 heat treatment. This investigation makes it possible to significantly improve the efficiency of heat treatment on A356 alloy and, at the same time, improve the mechanical properties of the alloy.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Youn S W, Kang C G. Characterization of age-hardening behavior of eutectic region in squeeze-cast A356-T5 alloy using nanoindenter and atomic force microscope. Materials Science & Engineering A, 2006, 425: 28–35.
Zhang L Y, Jiang Y H, Ma Z, et al. Effect of cooling rate on solidified microstructure and mechanical properties of aluminum A356 alloy. Journal of Materials Processing Technology, 2008, 207: 107–111.
Roy M J, Maijer D M, Dancoine L. Constitutive behavior of as-cast A356. Materials Science & Engineering A, 2012, 548: 195–205.
Boschetto A, Costanza G, Quadrini F, et al. Cooling rate inference in aluminum alloy squeeze casting. Materials Letters, 2007, 61: 2969–2972.
Qayyum M S. Production of a Permanent Mold Gravity Die Cast A356.0 Aluminum Alloy Motorbike Shock Absorber through Casting Simulation. Key Engineering Materials, 2015, 659: 676–680.
Makhlouf M M, Guthy H V. The aluminum-silicon eutectic reaction: mechanisms and crystallography. Journal of Light Metals, 2001, 1: 199–218.
Myhr O R, et al. Modeling of the microstructure and strength evolution in Al-Mg-Si alloys during multistage thermal processing. ActaMaterialia, 2004, 52: 4997–5008.
Zhu M, Jian Z, Yang G, et al. Effects of T6 heat treatment on the microstructure, tensile properties, and fracture behavior of the modified A356 alloys. Materials & Design, 2012, 36: 243–249.
Zhang D L, Zheng L H, St John D H. Effect of a short solution treatment time on microstructure and mechanical properties of modified Al-7wt%Si-0.3wt.%Mg alloy. Journal of Light Metals, 2002, 2: 27–36.
Menargues S, Martín E, Baile M T, et al. New short T6 heat treatments for aluminum silicon alloys obtained by semisolid forming. Materials Science & Engineering A, 2015, 621: 236–242.
Shivkumar S, Wang L, Keller C. Impact properties of A356-T6 alloys. Journal of Materials Engineering and Performance, 1994, 3: 83–90.
Yang C L, Li Y B, Dang B, et al. Effects of cooling rate on solution heat treatment of as-cast A356 alloy. Transactions of Nonferrous Metals Society of China, 2015, 25: 3189–3196.
Zhang Z, Tezuka H, and Kobayashi E. Effects of the Mn/Fe Ratio and Cooling Rate on the Modification of Fe Intermetallic Compounds in Cast A356 Based Alloy with Different Fe Contents. Materials Transactions, 2013, 54: 1484–1490.
Ogris E, Wahlen A, Lüchinger H, et al. On the silicon spheroidization in Al-Si alloys. Journal of Light Metals, 2002, 2: 263–269.
Andersen S J, Marioara C D, Vissers R, et al. The structural relation between precipitates in Al-Mg-Si alloys, the Al-matrix and diamond silicon, with emphasis on the trigonal phase U1-MgAl2Si2. Materials Science & Engineering A, 2007, 444: 157–169.
Taylor J A, Schaffer G B, St John D H. The role of iron in the formation of porosity in Al-Si-Cu-based casting alloys: Part II. A phase-diagram approach. Metallurgical and Materials Transactions A, 1999, 30: 1651–1655.
Polmear L J. Light alloys: metallurgy of the light metals. John Wiley & Sons Press, 1995.
Vissers R, Huis M A V, Jansen J, et al. The crystal structure of the β′ phase in Al-Mg-Si alloys. Acta Materialia, 2007, 55: 3815–3823.
Andersen S J, Zandbergen H W, Jansen J, et al. The crystal structure of the β″ phase in Al-Mg-Si alloys. Acta Materialia, 2007, 46: 3283–3298.
Author information
Authors and Affiliations
Corresponding author
Additional information
Rui Du Male, born in 1993, Ph. D candidate. His research interests mainly focus on the light-weight materials, and metal matrix composites.
Rights and permissions
About this article
Cite this article
Lu, Sp., Du, R., Liu, Jp. et al. A new fast heat treatment process for cast A356 alloy motorcycle wheel hubs. China Foundry 15, 11–16 (2018). https://doi.org/10.1007/s41230-018-7058-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41230-018-7058-x