Abstract
Effect of high frequency peening treatment with a small radius tip pin, which is less than 3mm radius tip pin, still remains unclear, although the effect of ultrasonic impact treatment on fatigue strength has been investigated. The objective of this study is to investigate the effect of ultrasonic peening with a 1.5mm radius tip pin on fatigue strength of out-of-plane gusset welded joints. Plate bending fatigue tests of those joints carried out. The results show that the peening can improve fatigue strength, when mean stress does not change or already changes before the peening is carried out. It also shows that the effect of the ultrasonic impact peening become less with increasing mean stress after the ultrasonic peening was carried out, and when the ultrasonic peening is not sufficient for the weld toe.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Anami, K., Miki, C., Tani, H., and Yamamoto, H. (2000). “Improving fatigue strength of welded joints by hammer peening and TIG-dressing.” Journal of Structure Mechanics and Earthquake Engineering, JSCE, No. 647, pp. 57s–68s.
JSSC (1993). Fatigue Design Recommendation for Steel Structures. Japanese Society of Steel Construction (in Japanese).
Kakiichi, T., Yamada, K., Ishikawa, T., Tanaka, R., Shimanuki, H., and Nose, T. (2009) “Plate bending fatigue test of out-of-plane gusset joints treated by ultrasonic peening.” Proc. JSCE 64th Annual Assembly, JSCE, I-148, pp. 295–296 (in Japanese).
Kinoshita, K., and Imamura A. (2010). “Investivation of fatigue strength evaluation of out-of-plane gusseted welded joints treated by ultrasonic peening.” Proc. Constructional Steel, 18, pp. 127–132 (in Japanese).
Kinoshita, K., Imamura A., Watanabe Y., and Handa, M. (2014a). “Fatigue strength improvement of out-of-plane gusset joints under plate bending by ultrasonic peening.” Proc. Seventh International Conference on Bridge Maintenance, Safety and Management and Life-Cycle Optimization (IABMAS2014), pp. 1382–1385.
Kinoshita, K., Imamura A., Watanabe Y., and Handa, M. (2014b). “Fatigue strength of out-of-plane gusset treated by ultrasonic needle peening with a small radius tip pin.” Steel Construction Engineering, 21(83), pp. 11–18 (in Japanese).
Mori, T., Shimanuki, H., and Tanaka, M. (2012). “Effect off UIT on fatigue strength of web-gusset welded joints considering service condition of steel structures.” Welding in the World, 56 (9–10), pp.141–149.
Roy, S. and Fisher, J. W. (2005) “Enhancing fatigue strength by ultrasonic impact treatment.” International Journal of Steel Structures, 5(3), pp. 241–252.
Tominaga, T., Matsuoka, K., and Satoh, Y. (2007). “Fatigue improvement method for weld repaired crane runway girder by ultrasonic impact treatment.” Steel Construction Engineering, JSSC, 14(55), pp. 47–58 (in Japanese).
Yamada, K., Ojio, T., Torii, A., Bail, B., Sasaki, Y., and Yamada, S. (2008). “Influence of shot blasting on fatigue strength of out-of-plane gusseted specimens under bending.” Journal of Structural Engineering, JSCE, 54A, pp. 522–529 (in Japanese).
Author information
Authors and Affiliations
Corresponding author
Additional information
Discussion open until May 1, 2015. This manuscript for this paper was submitted for review and possible publication on March 4, 2014; approved on December 1, 2014.
Rights and permissions
About this article
Cite this article
Kinoshita, K., Imamura, A., Watanabe, Y. et al. Effects of ultrasonic peening on fatigue strength of out-of-plane gusset joints. Int J Steel Struct 14, 769–776 (2014). https://doi.org/10.1007/s13296-014-1208-9
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13296-014-1208-9