Abstract
In gas flooding, one of the major problems in implementing foam as a gas mobility control method is the stability of foam. Foam booster when blended with surfactant could improve the foam stability. However, the influence of foam booster on the conventional foam stability and foamability at elevated temperature and presence of inorganic electrolytes is not yet explicit due to limited studies in this area. The objective of the present work was to evaluate the influence of a foam booster on aqueous solution stability, foamability and foam stability when blended with surfactant at different ratios at an elevated temperature in the presence of brine composed of monovalent and divalent ions. Three different surfactants AOS C14–16 (alpha-olefin sulfonate), SDS (sodium dodecyl sulfate) and a locally manufactured surfactant ‘Surf X’ were chosen as base surfactants. An amphoteric surfactant lauryl betaine was chosen as a foam booster in this study. The aqueous solution stability was visually evaluated, whereas the bulk foam experiments were conducted in a commercial foam analyzer apparatus. It was found that not all solutions were stable when lauryl betaine was blended. Lauryl betaine did not improve the foam generation time. The foam stability was improved; however, not all solutions were able to generate stable foam. ‘Surf X’ was able to generate more stable foam as compared to AOS and when blended with lauryl betaine it also required less amount of lauryl betaine to generate stable foam.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Foam is a dispersion of gas in a liquid phase such that the liquid is in continuous phase having some of the gas trapped inside the thin liquid films known as lamellae (Hiraski 1989). The surfactant molecules are present at the gas liquid interface, and thereby stabilize the foam films (Katgert 2008; Yekeen et al. 2017a). In gas flooding, the challenge associated with injected gas is poor volumetric sweep efficiency, because of low viscosity and density of gas compared to oil (Memon et al. 2016). Foam has higher apparent viscosity and can control the mobility of the gas by substantially hinder the gas flow in porous media, which forces gas to sweep pores that it would not have reached without foam (Farajzadeh et al. 2012). In short foam divert gas toward zones having lower permeability, it limits viscous fingering and also reduces overriding of gas in high permeability zones of reservoir (Yekeen et al. 2018; Chevallier et al. 2019). There are two main methods by which foam can be generated in porous media, surfactant alternating gas (SAG) and co-injection of surfactant and gas (Jensen and Friedmann 1987; Farajzadeh et al. 2012).
As an enhanced oil recovery (EOR) method, a major concern with the application of foam is the stability of foam (Yekeen et al. 2018). The selection and concentration of proper foaming agents are one of the main parameters that determines the success of foam flooding (Rafati et al. 2012). Compared to an individual component, studies have shown that when foam booster is used as an additive they may improve the foam properties (Van Der Bent 2014; Cui, 2014; Osei-Bonsu et al. 2015; Sakai and Kaneko 2004). Betaines are known for their foam enhancing properties (Sakai and Kaneko 2004; Farajzadeh et al. 2012).
Previous studies have shown that zwitterionic betaine surfactants have the ability to improve stability of the foam films in the absence and presence of oil (Basheva et al. 2000; Cui 2014). Gao et al. 2017 in their research shown that the addition of betaine improves the foam stability. It was observed that more stable foam was generated when lauryl betaine was added to the NI (Neodol 67-7PO sulfate and IOS15–18) 4:1 blend (Li et al. 2012). Lauryl betaine is an amphoteric surfactant that is thermally stable relative to cocamidopropyl-betaine (Cui 2014). It was also observed in some other studies that blending lauryl betaine does improve the foam properties (Conn et al. 2014; Singh and Mohanty 2016). The blend tested by Singh and Mohanty (2016) consisted of (1:1) AOS and LB with brine having salinity 1.2 wt% without the presence of divalent ions,. whereas Conn et al. (2014) study was limited to 1:1 of main surfactant (AOS) and lauryl betaine as foam booster with a total concentration of 1 wt%, in the presence of NaCl brine.
The presence of divalent ions can cause the surfactant to precipitate in the formation because of the intolerance of many surfactants to the divalent ions. So it is important to test surfactant solutions for foam studies in the presence of divalent ions. However, when mixed with different surfactants, the influence of lauryl betaine on aqueous solution stability, foamability and foam stability in the presence of divalent ions at high temperature has not been extensively investigated in previous studies.
This experimental evaluation studied the influence of lauryl betaine on aqueous solution stability, foamability and foam stability when blended with surfactant at different ratios in the presence of brine containing divalent ions at 60 °C. In this work AOS C14–16, SDS and a locally manufactured surfactant ‘Surf X’ chosen as base surfactant was systematically blended with lauryl betaine (foam booster) at different ratios in a brine containing NaCl and CaCl2. Except the foam stability test which was conducted at only 60 °C, all other tests were conducted at 25 °C and 60 °C. The aqueous solution stability was visually evaluated, whereas the foamability and foam stability experiments were conducted in a commercial Foamscan apparatus. In bulk foam tests, half-life (foam stability) and foamability were investigated. In this study, a comparative understanding of the influence of lauryl betaine (which we here after called LB) on aqueous solution stability, foamability, foam stability when blended with base surfactant was studied to generate a stable foam solution that can be further tested in porous media.
Materials and methods
Materials
AOS C14-16 (Alpha-olefin sulfonate) was obtained from STEPAN Chemical Co. ‘Surf X’ a locally developed surfactant, SDS (sodium dodecyl sulfate) from Sigma Co. and Fentacare BS12/Lauryl Betaine (additive), received from Solvay Chemicals Co. The brine was prepared with deionized water and with the concentration of 3.0 wt% of NaCl from Merck Co., 0.20 wt% CaCl2 from R&M Chemicals. The total brine salinity was 3.2 wt%. Pure N2 gas was used in this study as the sparging gas. The injection rate was 50 ml/min for all the solutions. All the solution contained total concentration of 0.5 wt% active surfactant. The concentration used in this study was well above the critical micelle concentration. The CMC value of AOS at 3.0 wt% NaCl brine was 0.003 wt% (Laskaris 2015).
The details of the surfactant solutions tested in this study are given in Table 1. Label A 100, S 100 and X 100 denotes to AOS, SDS and ‘Surf X’, respectively, without the LB blend, whereas A 91, S 91, X 91 shows 9:1, A 73, S 73, X 73 shows 7:3 and A 64, X 64, S 64 shows 6:4 blends of AOS, SDS and ‘Surf X’ with LB, respectively.
Experimental procedure
This research is divided into two main phases. In the first phase, the aqueous stability testing of the surfactant solution was conducted. In aqueous stability testing, there were two types of test. First one is the precipitation testing (in this test the solutions were checked for any type of precipitation) and second is the thermal stability testing (in this test, phase separation was checked). First the individual surfactants were tested. In the second part, the foam booster (LB) was added at different ratios as mentioned in Table 1. The surfactant solutions were stored at different temperatures (25 °C and 60 °C) for 2 weeks, which were than visually inspected. A surfactant solution is considered stable, if the solution is homogeneous, contain single phase and clear. If the surfactant solution that is used for injection is not in single phase and clear will have significant phase trapping, formation plugging, and loss of surfactant solution to adsorption in the formation will occur. As shown in Fig. 1 if the solution was clear or slightly blurry, it was considered aqueously stable. If a solution was cloudy or if a solution has precipitates, then it was considered unstable and was not used for further testing.
In the second phase, the bulk foam experiments were carried out using Foamscan apparatus (Teclis instruments) ®. Figure 2 shows the schematic diagram of the foam analyzer apparatus used in this research. Bulk foam test was conducted at ambient and 60 °C. First, a 50 ml of the solution sample was injected into the glass tube after that the pure N2 (nitrogen) gas at 50 ml/min was injected as sparging gas to create the foam. The foamability of the solutions was tested by generating up to 100 ml of foam, and then, the time for the foam to reach the 100 ml foam volume was recorded. The bulk foam stability was measured by (half-life) the time needed for the foam to decay into half of its original volume after the sparging of the gas was stopped.
Results and discussion
Aqueous and thermal solution stability testing
A qualified surfactant formulation for foam EOR should be soluble and stable from injection to reservoir conditions (Cui 2014). It is important to test aqueous and thermal solution stability because if a solution is not stable (single phase) and precipitates inside formation then it will block the pores and damage the formation. Results of the aqueous solution stability tests can be seen in Table 2. All the base surfactant solutions in the presence of brine were tested at temperatures 25 °C and 60 °C. Tested base surfactant solutions were found clear, and no phase separation and precipitation were observed. The base surfactant was then further used to blend with the LB for further testing. In the second phase, the foam booster (LB) was blended with the base surfactant at ratios 9:1, 7:3 and 6:4 as mentioned in Table 1. After blending the LB and base surfactants, aqueous and thermal stability were tested.
The solutions A 91, A 73, X 91, X 73 were found stable, and no phase separation or precipitation was observed at both temperatures 25 °C and 60 °C. The A 73 showed a little blurry solution at 25 °C temperature; however, when it was tested at 60 °C, it was found clear. The solution A 64, X 64, S 73 and S 64 were cloudy and has precipitation at 25 °C. When these solutions were further tested at 60 °C. Precipitations and cloudy solutions were still observed; however, the solution S 73 at 60 °C was hazy, but the precipitation was still present in the solution. It was observed in this study that as the ratio of LB increased in the surfactant solutions, it had a negative influence on the stability of the surfactant solution. Not all the surfactant solutions were found stable as the ratio of LB increased in the surfactant solution. Complex interaction among the divalent ions and surfactant molecules could have the possibility of reduction in micelle formation that would lead to presence of large number of free monomers which in turn bind with divalent ions. This binding of divalent ions could be the possible reason for precipitation. The A 64, X 64, S 100, S 91, S73 and S 64 surfactant solutions was not further used for testing in this study.
Bulk foam test
Foamability
The ease of foam generation is known as foamability. It is a dynamic property of foam generating power of a liquid and the factors that help to attain immediate stabilization of the foam (Wilson 1996; Sakai and Kaneko 2004). The influence of LB on foamability is shown in Fig. 3a at 25 °C and Fig. 3b at 60 °C when blended with AOS and ‘Surf X’ surfactant, respectively. As shown in Fig. 3a, b, the foamability time of the individual surfactant solutions as compared to the mixed surfactant solutions was better.
As shown in Fig. 3a, when AOS was blended with LB at 9:1, the foamability time at 25 °C was increased by 39.08%. At 7:3, the time was increased by 27.58%. When ‘Surf X’ was blended with LB at 9:1, the time was 27.47% more than individual ‘Surf X’. At 7:3, the foamability time was increased by 30.76% as compared to the time for base ‘Surf X’ surfactant.
Figure 3b represents the foamability of surfactant solutions at 60 °C. When AOS was blended with LB at 9:1, the foamability time was increased by 26.47%. At 7:3, the time was increased by 20.58%. When ‘Surf X’ was blended with LB at 9:1, the time was only 5.79% more. At 7:3, the foamability time was 27.53% more as compared to the time for ‘Surf X’ without the blend of LB.
Temperature had a positive effect on the foamability of all the surfactant solutions tested in this study. The foamability time of surfactant solutions at elevated temperature was much better as compared to the foamability time at lower temperature. The improvement in foamability at 60 °C compared to 25 °C could be attributed to the increase in the internal kinetic energy of the gas due to increase in temperature and the decrease in liquid viscosity of the surfactant solution. At both temperatures 25 °C and 60 °C, the surfactant solutions A 100 and X 100 without the blend of LB had better foamability time. The foamability performance of the surfactant solutions tested in this study at 25 °C are ranked in the order of: A 100 > X 100 > A 73 > X 91 > X 73 > A 91, whereas at 60 °C temperature the order is as follows: A 100 > X 100 > X 91 > A 73 > A 91 > X 73.
In this work, LB was not able to have a positive impact on the foamability of surfactant solutions used. LB has more negative impact on foamability when blended with AOS as compared to the ‘Surf X’ surfactant. (Sakai and Kaneko 2004; Van Der Bent 2014) in their study also found the similar trend that the addition of amphoteric surfactant did not improve the foamability. Figure 4 shows A 100 foam generated inside a glass tube.
Foam stability
Foam stability can be defined as the time a foam film exists without rupturing (Sakai and Kaneko 2004). It is generally indicated by foam half-life (time needed for foam to decay half of its original foam) (Yekeen et al. 2017b) Fig. 5 shows the half-life of the bulk foam experiments, both with and without the blend of LB at 60 °C, with longer half-life indicating a more stable foam. AOS and LB blend of 9:1 generated 149.68% more stable foam as compared to individual AOS surfactant solutions. When AOS was blended with LB at ratio of 7:3, it increased half-life by 254.91%. When ‘Surf X’ was blended with LB at 9:1, it showed an improvement in stability by just 8.92%; however, when the blend ratio was increased and the ‘Surf X’ and LB was blended at 7:3, there was a decrease in stability of about 39.89%.
In comparison of individual surfactant solution, X 100 has higher foam stability as compared to A 100 surfactant solution generated foam. The half-life of the surfactant solutions was improved when LB was blended with the AOS and ‘Surf X’ surfactants. The influence on the stability was more profound with AOS surfactant as compared to the ‘Surf X’ surfactant. Among all the surfactant blended with the LB, ‘Surf X’ needed less amount of LB as compared to the AOS. Increasing the ratio of LB with ‘Surf X’ was not able to greatly improve foam stability at all the ratios tested. The A 73 surfactant solution generated the most stable foam among all the surfactant solution tested. Based on Fig. 5, the foam stability according to half-life is ranked as the following A 73 > X 91 > X 100 > A 91 > X 73 > A 100. The increase in foam stability with the blend of an amphoteric surfactant has also been reported by other researchers (Osei-Bonsu et al. 2015; Memon et al. 2016). As compared to individual component systems, the blend of different type of surfactants synergistically exhibit better foaming properties (Bian et al. 2012; Memon et al. 2016).
This result of the increase in the foam stability by LB can be due to the Marangoni effect, which is caused by electrostatic attraction between anionic surfactant and the cationic nitrogen (Domingo 1996; Sakai and Kaneko 2004). Gao et al. (2017) showed in their study using the simulation for foam stability that the presence of amphoteric surfactant relaxes the repulsion between the headgroups of anionic surfactants. This mechanism improved the foam stability and could also be responsible for the improved foam stability in the presence of LB as observed in this research. Moreover, it is anticipated that addition of LB to the solution could increase the liquid viscosity, consequently decreasing the liquid drainage from the foam plateau borders which causes high resistance to film thinning, thus influences the stability of foam (Osei-Bonsu et al. 2015).
Conclusion
In this work, when blended with different solutions, the influence of lauryl betaine on the aqueous solution stability, foamability and bulk foam stability in the presence of divalent ions and at an elevated temperature were studied. Parameters such as the aqueous solution stability (phase separation and precipitation), foamability and foam stability were systematically investigated. It was found that blending lauryl betaine with surfactant affects the solution stability; not all the solution was found stable as the ratio of LB increased in the surfactant solution in the presence of divalent ions. There was a negative impact on foamability when lauryl betaine was blended with the surfactant. A 100 and X 100 surfactant solutions had the best foamability time at both the tested temperatures. The foam stability of the solutions was improved; however, not all solutions were able to generate stable foam. ‘Surf X’ individually was able to generate more stable foam as compared to AOS and when blended with lauryl betaine. It also required less amount of lauryl betaine to generate more stable foam. The A 73 surfactant solution generated the most stable foam followed by X 91 surfactant solution. The presence of lauryl betaine (10%) in ‘Surf X’ increased the foam stability by approximately 9%, whereas the presence of lauryl betaine (30%) in AOS surfactant solution increased the foam stability by approximately 255%. The surfactant solution used in this study that generated stable foam will be further tested in porous media.
References
Basheva ES, Ganchev D, Denkov ND et al (2000) Role of betaine as foam booster in the presence of silicone oil drops. Langmuir 16:1000–1013. https://doi.org/10.1021/la990777+
Bian Y, Penny GS, Sheppard NC et al (2012) Surfactant formulation evaluation for carbon dioxide foam flooding in heterogeneous sandstone reservoir. SPE Improv Oil Recover Symp. https://doi.org/10.2118/154018-ms
Chevallier E, Demazy N, Cuenca A, Chabert M (2019) Correlation between foam flow structure in porous media and surfactant formulation properties. Transp Porous Media. https://doi.org/10.1007/s11242-018-01226-2
Conn CA, Ma K, Hirasaki GJ, Biswal SL (2014) Visualizing oil displacement with foam in a microfluidic device with permeability contrast. Lab Chip 14:3968–3977. https://doi.org/10.1039/c4lc00620h
Cui L (2014) Application of foam for mobility control in enhanced oil recovery (EOR) process. PhD dissertation, Rice University
Domingo X (1996) Betaines. In: Lomax EG (ed) Amphoteric surfactants, 2nd edn. Marcel Dekker, New York, p 75
Farajzadeh R, Andrianov A, Krastev R et al (2012) Foam-oil interaction in porous media: implications for foam assisted enhanced oil recovery. Adv Colloid Interface Sci 183–184:1–13. https://doi.org/10.1016/j.cis.2012.07.002
Gao F, Liu G, Yuan S (2017) The effect of betaine on the foam stability: molecular simulation. Appl Surf Sci 407:156–161. https://doi.org/10.1016/j.apsusc.2017.02.087
Hiraski GJ (1989) The steam-foam process. Soc Pet Eng. https://doi.org/10.2118/19505-pa
Jensen JA, Friedmann F (1987) Physical and chemical effects of an oil phase on the propagation of foam in porous media. SPE California Regional Meeting. Society of Petroleum Engineers, Ventura, California. https://doi.org/10.2118/16375-MS
Jones SA, van der Bent V, Farajzadeh R, Rossen WR, Vincent-Bonnieu S (2016) Surfactant screening for foam EOR: Correlation between bulk and core-flood experiments. Colloids Surf Physicochem Eng Asp 500:166–176. https://doi.org/10.1016/j.colsurfa.2016.03.072
Katgert G (2008) Flow of foams. Doctoral Dissertation, Universiteit Leiden
Laskaris G (2015) Effect of surfactant concentration, water treatment chemicals, fatty acids and alcohols on foam behavior in porous media and in bulk. Masters dissertation, TU Delft University, Netherland
Li RF, Hirasaki G, Miller CA, Masalmeh SK (2012) Wettability alteration and foam mobility control in a layered, 2d heterogeneous sandpack. SPE Int Symp Oilf Chem. https://doi.org/10.2118/141462-pa
Memon MK, Shuker MT, Elraies KA (2016) Study of blended surfactants to generate stable foam in presence of crude oil for gas mobility control. J Pet Explor Prod Technol 7:77–85. https://doi.org/10.1007/s13202-016-0243-9
Osei-Bonsu K, Shokri N, Grassia P (2015) Foam stability in the presence and absence of hydrocarbons: from bubble- to bulk-scale. Colloids Surf A Physicochem Eng Asp 481:514–526. https://doi.org/10.1016/j.colsurfa.2015.06.023
Rafati R, Hamidi H, Idris AK, Manan MA (2012) Application of sustainable foaming agents to control the mobility of carbon dioxide in enhanced oil recovery. Egypt J Pet 21:155–163. https://doi.org/10.1016/j.ejpe.2012.11.010
Sakai T, Kaneko Y (2004) The effect of some foam boosters on the foamability and foam stability of anionic systems. J Surfactants Deterg 7:291–295. https://doi.org/10.1007/s11743-004-0314-x
Singh R, Mohanty KK (2016) Foams with wettability-altering capabilities for oil-wet carbonates: a synergistic approach. SPE J 21:1126–1139. https://doi.org/10.2118/175027-PA
Van Der Bent VJ (2014) Comparative study of foam stability in bulk and porous media. Masters thesis, Delft University of Technology
Wilson AJ (1996) Experimental techniques for the characterization of foams. In: Prud’homme RK, Khan SA (eds) Foams: theory, measurements, and application. Marchel Dekker, Inc, New York, pp 243–272
Yekeen N, Idris AK, Manan MA, Samin AM (2017a) Experimental study of the influence of silica nanoparticles on the bulk stability of SDS-foam in the presence of oil. J Dispers Sci Technol 38:416–424. https://doi.org/10.1080/01932691.2016.1172969
Yekeen N, Manan MA, Idris AK, Samin AM (2017b) Influence of surfactant and electrolyte concentrations on surfactant Adsorption and foaming characteristics. J Pet Sci Eng 149:612–622. https://doi.org/10.1016/j.petrol.2016.11.018
Yekeen N, Manan MA, Idris AK et al (2018) A comprehensive review of experimental studies of nanoparticles-stabilized foam for enhanced oil recovery. J Pet Sci Eng 164:43–74. https://doi.org/10.1016/j.petrol.2018.01.035
Acknowledgement
Authors would like to thank Stepan Co. and Solvay Chemicals Co. for providing chemicals used in this research. Authors would also like to thank Institute of Hydrocarbon Recovery, Centre of Research of Enhanced Oil Recovery (COREOR), Universiti Teknologi PETRONAS and to the Ministry of Higher Education (MOHE), (0153AB-L59) for supporting this research through fundamental research Grant scheme.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Syed, A.H., Idris, A.K., Mohshim, D.F. et al. Influence of lauryl betaine on aqueous solution stability, foamability and foam stability. J Petrol Explor Prod Technol 9, 2659–2665 (2019). https://doi.org/10.1007/s13202-019-0652-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13202-019-0652-7